• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.74-79
• /
• 2002

The EM(Engineering Model) VCO(Voltage Controlled Oscillator) is nonlinear designed for LO(Local Oscillator) of Ka-band satellite transponder. The microstripline coupled with dielectric resonator is implemented as a high impedance inverter to improve the phase noise, and the quality factor of resonant circuit can be transferred to active device with the enhanced loaded quality factor. The developed VCO has the oscillating tuning range of 9.7965~9.8032 GHz for the control voltage range of 0~12 V. This VCO requires the DC power of 8 V and 17 mA. The phase noise characteristics are -96.51 dBc/Hz @10 KHz and -116.5 dBc/Hz @100 KHz, respectively. And, the output power of 7.33 dBm is measured.

• Journal of electromagnetic engineering and science
• /
• v.12 no.2
• /
• pp.176-184
• /
• 2012

In this paper, the effects of a metal plane on the performance of a meandered slot RFID antenna are evaluated in a real environment, and 3 metal plane cases are considered (the most likely scenarios in which metal conductive materials are placed near the tag antenna). The metal plane effects can be categorized as matching degradation and antenna gain variation. First, matching degradation due to the antenna's induced mutual impedance is experimentally investigated. In addition, the gain variation is investigated to figure out the change in the radiation characteristics. With the derived antenna parameters, the read range is calculated with the Friis transmission equation and measured to analyze the effects of a metal plane on RFID system performance. The calculated and measured read range varies from 9.3 m to 19.1 m as the distance between the RFID antenna and the metal plane changes.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.561-568
• /
• 2003

There arc two ways in the output voltage control method in PWM inverters. One Is double loop voltage control composed of inner current control loop and outer voltage control loop.'rho other is single loop voltage control method composed of voltage control loop only. It's characteristics shows lower performance in case of high output impedance than double loop voltage control. However, in case of low output impedance, it shows good control performance in all load ranges than double loop voltage control. In this paper, the rule and the gain of single loop voltage control have been developed analytically and these were verified through computer simulation and experiment.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.496-500
• /
• 2001

There are two ways in the output voltage control method in PWM inverter. One is the double loop voltage control composed of inner current control loop and outer voltage control loop. Because it shows fast response and low steady state error, utilized in many application. The Other is single loop voltage control method composed of voltage control loop only. It's characteristics shows lower performance in case of high output impedance than double loop voltage control. But in low output impedance, it shows good control performance in all load range than double loop control. In this paper, single loop voltage control rule and gain was developed analytically, and these were verified through computer simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1408-1409
• /
• 2006

In this paper, poly methyl methacrylate thin films were deposited on a ITO glass substrate using a plasma polymerization technique. In order to investigate the influence of the plasma coupling method and plasma conditions on the plasma polymerized poly methyl methacrylate (ppMMA) thin film properties, inductively coupled (ICP) and capacitively coupled plasma (CCP) were used to generate the plasma and the plasma parameters were varied. Molecular structures of the ppMMAs were investigated using a Fourier Transform Infrared (FT-IR) spectroscopy. Dielectric constants of the ppMMA thin films were investigated using a impedance analyzer (HP4192A, LF Impedance Analyzer). Current-Voltage (I-V) characteristics of the ppMMA thin films were investigated using a source measurement unit (SMU: Keithley 2400). Relationship between the plasma coupling technique/process parameter and ppMMA thin films properties were investigated.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1347-1348
• /
• 2007

In this paper, ITO gate electrode surface was modified using $O_2$ plasma and organic gate insulating layers were deposited on the ITO surface using plasma polymerization technique. In order to investigate the influence of the plasma coupling method and plasma conditions on the plasma polymerized methyl methacrylate (ppMMA) thin film properties, inductively coupled (ICP) and capacitively coupled plasma (CCP) were used to generate the plasma and the plasma parameters were varied. The ppMMAs were investigated using atomic force microscopy (AFM) and a Fourier Transform Infrared (FT-IR) spectroscopy. Dielectric constants of the ppMMA thin films were investigated using a impedance analyzer (HP4192A, LF Impedance Analyzer). Current-Voltage (I-V) characteristics of the organic thin film transistors (OTFTs) were investigated using a source measurement unit (SMU: Keithley 2612). Proposed method can be applied to dry-process to fabricate OTFTs during overall fabricating steps.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.559-562
• /
• 2004

The $high-T_c$ Superconducting(HTS) antenna which consists of "H" type resonator has the benefits for the miniaturization of antenna in comparison with the microstrip antenna of the similar dimension. To fabricate the "H" type antenna HTS $YBa_2Cu_3O_{7-x}$(YBCO) thin films were deposited on MgO substrates using rf-magnetron sputtering. Standard etching processes were performed for the patterning of the "H" type antenna. For comparison between normal conducting antennas and superconducting antennas, the gold antennas with the same dimension were also fabricated. An aperture coupling was used for impedance matching between $50\Omega$ feed line and HTS radiating patch. The diverse experimental results were reported in terms of the resonant frequency, the return loss and the characteristics impedance. The "H" type superconducting antenna showed the performance of 1.36 in SWR, 24 % in efficiency, and 14.6 dB in the return loss superior to the normal conducting counterpart.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.193-196
• /
• 2005

유기발광소자의 발광층의 두께에 따른 임피던스의 변화를 살펴보았다. 임피던스는 두께에 따라 저항의 변화에 따른 의존성을 보이며, 그에 따른 임피던스와 Cole-Cole 반원의 변화, 두께에 따른 $1/\tau$ 의 변화를 살펴보았다. 발광층의 두께는 각각 100, 200, 300 nm의 두께로 열증착하여 실험하였고, 소자의 구조는 $ITO/Alq_3/Al$의 구조로 측정 하였다. 유기발광소자의 발광층인 $Alq_3$의 두께가 증가함에 따라 임피던스의 크기가 증가하고, 위상각의 크기는 100nm의 경우 0V에서 용량성을 보이다가 6~10V까지 부성저항특성을 나타낸 후 약 22V에서 저항성을 나타내고, 200과 300 nm의 경우 12V까지 용량성을 나타내다 이후 22V 근방에서 $0^{\circ}$에 가까워지며 저항성을 나타내는 것을 알 수 있었다. 또한 두께에 따른 Cole-Cole 반원을 살펴보면 두께가 증가할수록 반원의 크기가 증가하는 것을 알 수 있으며, 이를 통해 간단한 등가회로를 예측할 수 있었다. 그리고 벌크내의 용량성$(C_p)$을 측정하여 두께의 증가에 따라 $C_p$ 값이 감소하는 것을 알 수 있었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.918-921
• /
• 2005

According to the mechanical-electrical coupling characteristics and the electrical Impedance property of resistor-inductor-capacitor(RLC) series resonant circuit, the mechanical impedance analysis of a bimorph piezoceramic patch shunted with a series RLC resonant circuit is conducted. The displacement transfer function of a cantilever beam bonded with a piezoelectric shunt damping module is deduced in the case of single mode vibration of the beam. By the use of vibration damping theory of tuned mass damper system, the parameter optimization of piezoelectric shunt damping system is performed. The optimal resonant state of the shunting circuit can be obtained when the resister and conductor are optimally adjusted. Test results show that the vibration control effect as well improved with optimized piezoelectric shunt system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.10
• /
• pp.923-930
• /
• 2010

Finite element models of dynamic systems can be updated in two stages. In the first stage, mass and stiffness matrices are updated neglecting damping, and in the second stage, damping matrices are estimated with the mass and stiffness matrices fixed. Three methods to estimate damping matrices for this purpose are proposed in this paper. The methods include one for proportional damping systems and two for non-proportional damping systems. Method 1 utilizes orthogonality of normal modes and estimates damping matrices using the modal parameters extracted from the measured responses. Method 2 estimates damping matrices from impedance matrices which are the inverse of FRF matrices. Method 3 estimates damping using the equation which relates a damping matrix to the difference between the analytical and measured FRFs. The characteristics of the three methods are investigated by applying them to simulated discrete system data and experimental cantilever beam data.