• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.150-150
• /
• 2011

Electron-neutral collision frequency is one of the important parameters in the plasma physics. Recently, It is employed to monitor the plasma processing in industrial plasma engineering [1]. Using the wave-cutoff probe with network analyzer, the plasma impedance was measured in inductively coupled argon plasma and analyzed to determine the resonance frequency. The electron-neutral collision frequency is directly calculated from the resonance frequency. The calculated electron-neutral collision frequency is good agree with reference which is calculated by measured EEDF using single langmuir probe (SLP).

• Journal of Sensor Science and Technology
• /
• v.5 no.1
• /
• pp.9-14
• /
• 1996

The effect on the microwave properties was investigated for the barium titanate doped with impurity of $WO_{3}$ 0.230 mole% produced by conventional solid state reaction method. Microwave resistance, reactance and impedance of the barium titanate were measured with 2-port s-parameter method by using network analyzer, in the range of room temperature to $160^{\circ}C$ and of frequency 300 kHz to 300 MHz. And possibility of frequency sensor and temperature sensor was estimated with barium titanate doped with $WO_{3}$.

• Journal of Magnetics
• /
• v.13 no.4
• /
• pp.177-181
• /
• 2008

A very simple a.c. magnetic susceptometer for use in a helium closed cycle cryostat is reported in this paper. This simple setup has only a single bobbin-less copper coil, instead of the primary coil and two secondary coils typically used in mutual-inductance types. The single bobbin-less copper coil is directly mounted on the cryostat cold head. A sample is attached on the inside wall of the copper coil using a thermal contact material and its a.c. magnetic susceptibility is obtained from the measurement of the self-inductance of the sample coil using an LCR meter or an impedance analyzer. Experimental details are described and illustrative measurements on magnetic and superconducting materials as a function of temperature are included. The performances and limitations of this simple a.c. magnetic suceptometer are also discussed.

• Journal of electromagnetic engineering and science
• /
• v.4 no.1
• /
• pp.43-49
• /
• 2004

A low-frequency coaxial reflectometer(LCR) with a thin-wire inner conductor is designed and constructed to measure nondestructively the absorbing performance of electromagnetic absorbers in the frequency range of 10 MHz to 200 MHz. The LCR consists of a square coaxial transmission line and a network analyzer with a time-domain measurement capability. Inherent characteristics of a square coaxial line with a thin-wire inner conductor which deteriorate the impedance matching of the input port of the LCR are addressed. And the characteristics are improved by employing a multiwire inner conductor. Measured and calculated reflection losses of a flat ferrite tile absorber are presented.

• Transactions of Materials Processing
• /
• v.11 no.7
• /
• pp.569-574
• /
• 2002

Recently, thick PZT films are required for the cases of micro piezoelectric devices with high driving force, high breakdown voltage and high sensitivity, and so on. In this work, thick PZT films were fabricated by Sol-Gel multi-coating method. Microstructures, and electrical properties of films were investigated by XRD, FESEM, impedance analyzer, and P-E hysteresis. PZT films with 2.7$mu extrm{m}$ to 4.4${\mu}{\textrm}{m}$ thickness were fabricated. Dielectric constant, loss, remnant polarization and coercive field of them were 880~1650 at 1kHz, 2~3% at 1kHz, 26~32 $\mu$C/$ extrm{cm}^2$, and 33~60kV/cm, respectively. Also a transverse piezoelectric coefficient $(e_{31,f})$ measurement system was fabricated and tested for thick film samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.331-334
• /
• 1998

The solid solutions of the Pb(Sc$\_$0.5/Nb$\_$0.5/)$\_$0.57/Ti$\_$0.43/O$_3$ system were prepared. In the PSNT system, it had been known that two-phase region between the rhombohedral and tetragonal phases was observed between 0.425 of PT at room temperature. In this paper, Fe$_2$O$_3$-doped 0.57PSN-0.43PT composition was prepared by conventional method. The dielectric and strain properties were examined using an computerized measuring apparatus, and the resonance characteristics were measured using an impedance gain phase analyzer. We got the data of dielectric constant, dielectric loss, piezoelectric coefficient, piezoelectric voltage coefficient, frequency constant strain constant mechanical quality factor and electromechanical coupling factor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.85-92
• /
• 2002

In this study, we analyzed and experimented micro-strip line inductors and capacitors for a SAW duplexer, an important devise for mobile communication. For SAW duplexers, micro-strip line lumped elements must have small impedance values, below several tens of nH or several tens of pF, and a small area pattern. In this study, we performed theoretical analysis of flat line type, meander line type, and spiral line type inductors and interdigital capacitors on a LiTaO$_3$ Piezo-crystal. We proposed a measurement method to evaluate small values of lumped elements accurately with network analyzer. In experiments, we confirmed validity of the theoretical analysis method through fabrication and characterization of micro-strip line lumped elements. The analysis method in this paper can be applied to SAW duplexers well as other microwave devices.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.787-794
• /
• 1995

To improvement the magnetic and frequency properties of YIG(Yttrium-Iron Garnet) in microwave region, it is investigated that the effect of $Al^{3+}$ ions on magnetic and frequency characteristics of YIG, using samples of basic YIG composition( $Y_{3}$F $e_{5}$ $O_{l2}$) added with A1$_{2}$ $O_{3}$ from 0 to 2.5 [mol%]. The measurment is conducted mainly for the structural properties and magnetical properties. The structural properties is measured using SEM(Scanning Electro Microscope), EDX(Energy-dispersive X-ray spectrometer) and XRD(X-ray diffraction equipment). The magnetical properties is measured with B-H curve tracer and impedance analyzer. As a result, it is confin-ned that the effect of eddy current loss is minimized while maintaining high saturation flux density of YIG, when YIG is added with 0.5 [mol%] of A1$_{2}$ $O_{3}$.>.>.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.23 no.5
• /
• pp.694-702
• /
• 1999

By using commercial available electromagnetic interference (EMI) shielding fabrics, EMI shielding effectiveness(SE) and the physical properties were investigated. Thirteen specimens were chosen six fabrics were non-electrolytic plated with Cu, six plated with Cu+Ni and one plated with Ni, SE was measured by RF Impedance Analyzer HP4291A(Hewlett Co, Ltd)at the frequency of 100MHz-1.8GHz. The results showed that the commercial EMI shielding fabrics provided SE values over 30dB at the frequency of 100MHz-1.8GHz. Fabrics plated with Cu showed more effective shielding than those plated with Ni. The thickness of coating and fabric count were also influential factors on SE. Tensile properties were acceptable for lining fabrics but water vapor transport properties indicated that the better treatment condition were suggested to improve comfort properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.299-299
• /
• 2007

This paper presents an omni-directional piezoelectric actuator which utilizes only one actuator. The actuator has a simple structure of cone type consists of two piezoelectric ceramics of ring type and electrodes divided four segments and a stainless steel body. To find the optimal operating condition of the actuator, the frequency characteristics of the actuator are analyzed by ATILA, FEM and measured by Impedance Analyzer. We have also developed a stage using the omni-directional actuator and an actuator driver circuit to create four sinusoidal waves with a variable frequency and phase difference.