• Journal of electromagnetic engineering and science
• /
• v.5 no.2
• /
• pp.97-103
• /
• 2005

This paper describes the measured results of sonobuoy transmitting antenna system for anti-submarine warfare (ASW). Since radiation pattern and power density depend on impedance matching between transmitting RF part and antenna with termination resistance, design of matching circuit is very important for sonobuoy system performance. Matching circuit is designed by Smith chart using control of L and C. In standing wave ratio(SWR) measurement using Network Analyzer, SWR of antenna with matching circuit observed 1.5 below at the assigned VHF band. It shows very excellent performance comparison with conversional product that is used for the same object. The measured vertical and horizontal radiation patterns are also shown the satisfaction of military specifications. A drop out of sonobuoy system on the sea is happened when angle of elevation direction is over 10 degrees, and it is conformed that it takes less than I second return to original signal level. The required electric power density is $83\;mW/m^2$ in the military specification, and measured electric power density is observed over average $110\;mW/m^2$ at all frequency bands.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.4
• /
• pp.717-722
• /
• 2013

In this study, we investigated the design of a wire wedge bonding ultrasonic tool horn using finite element method (FEM) simulations. The proposed method is based on an initial design estimate obtained by FEM analysis. An ultrasonic excitation causes various vibrations of a transducer horn and capillary. A simulated ultrasonic transducer horn and resonator are then built and characterized experimentally using a laser interferometer and electrical impedance analyzer. The vibration characteristics and resonance frequencies close to the exciting frequency are identified using ANSYS. FEM analysis is developed to predict the resonance frequency of the ultrasonic horn and use it in the optimal design of an ultrasonic horn mode shape.

• Composites Research
• /
• v.14 no.6
• /
• pp.38-46
• /
• 2001

In this study, An optimization code that can design microwave absorbing composite laminates is developed, and 3-layered microwave absorbing composite laminates are developed by optimizing the thickness of each layer. The layers are 3 different composite laminates. Many variables including lay-up angles of electromagnetically orthotropic composite layer can be considered in this code. The developed laminate is composed of an impedance matching layer of glass/epoxy fabric laminate, a glass/epoxy fabric laminate layer containing aluminum filler and carbon/epoxy fabric laminate layer. Permittivities of the materials are obtained using a network analyzer and a coaxial air line.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.725-729
• /
• 2014

In this study, a transparent conductive oxide (TCO)-less dye-sensitized solar cells (DSSCs) was fabricated by using titanium (Ti) electrode to replace the Fluorine-doped tin oxide (FTO) for the reduction of manufacturing cost. Ti film was formed by electron beam evaporation method and the results showed the sheet resistance of Ti electrodes with a thikness of 500 nm similar to FTO. In case of power conversion efficiency (PCE), a DSSC with Ti electrodes showed a lower value than that with FTO by 0.38%. For the investigation of the difference, the DSSCs were measured and analyzed by using electrochemical impedance analyzer (EIS).

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.5
• /
• pp.250-253
• /
• 2015

A novel implantable CPW fed Apollian shaped antenna embedded into human tissue is proposed for ISM band biomedical applications. The proposed antenna is made compatible for implantation by embedding it in an alumina ceramic substrate(ε_r=9.8 and thickness= 0.65 mm). The proposed antenna covers the ISM band of 2.45 GHz. The radiation parameters such as return loss, xy-plane, xz-plane, and yz-plane etc., are measured and analyzed using the agilent vector network analyzer. The proposed antenna has substantial advantages, including low profile, miniaturization ability, lower return loss, better impedance matching, and high gain over conventional implanted antennas.

• Korean Journal of Materials Research
• /
• v.12 no.6
• /
• pp.442-446
• /
• 2002

Design of microwave absorbers using high frequency properties of fiber reinforced composites are investigated. Two kinds of composite materials (glass and carbon) are used and their complex permittivity and permeability are measured by transmission/reflection technique using network analyzer. Low dielectric constant and nearly zero dielectric loss are determined in glass fiber composite. However, carbon fiber composites show the high dielectric constant and large conduction loss which is increased with anisotropy of fiber arrangement. It is, therefore, proposed that the glass and carbon fiber composites can be used as the impedance transformer (surface layer) and microwave reflector, respectively. By inserting the foam core or honeycomb core (which can be treated as an air layer) between glass and carbon fiber composites, microwave absorption above 10 dB (90% absorbance) in 4-12 GHz can be obtained. The proposed fiber composites laminates with sandwitch structure have high potential as lightweight and high strength microwave absorbers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.297-302
• /
• 2009

We have successfully fabricated the alumina thick films using inkjet printing processes without a high temperature sintering process. Alumina suspension as dielectric ink was formulated by combining nano-sized alumina powders with an anionic polymer dispersant in formamide/water as co-solvent. The thickness of the printed alumina thick film was measured at around 5 um by field emission scanning electron microscope. The calculated packing density of 68.5 % from the printed alumina thick film was much higher than the same films fabricated by conventional casting or dip coating processes. Q factor of the dielectrics thick film infiltrated with cyanate ester resin was evaluated by impedance analyzer.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.233-236
• /
• 2002

This paper has been designed and fabricated C-type micro, high-performance solenoid RF chip inductors with the size of 1.58$\times$0.82r0.94m0. The high frequency characteristics of simulated results obtained by HFSS were compared to those of measured results obtained by RF Impedance/Material Analyzer (HP16193A). Although the simulated inductance values were two times larger than the measured values and there are discrepancies in SRFs between simulated and measured values, it was observed that tile Q-factor values for fabricated inductors could be predicted from the simulated values.

• Journal of the Korean Ceramic Society
• /
• v.42 no.10 s.281
• /
• pp.685-690
• /
• 2005

Pb(Zr,Ti)$O_{3}$Pb($Mn_{1/3}$$Nb_{2/3}$)$O_{3}$ powder was successfully synthesised by high-energy milling method, and the behavior of low­temperature sintering and piezoelectrical properties of Pb(Zr,Ti)$O_{3}$-Pb($Mn_{1/3}$$Nb_{2/3}$)$O_{3}$ ceramics were investigated as a function of mechanical alloying time. In order to confirm whether the Perovskite phase in this composition was formed by mechanical activation technique or not, we performed X-Ray Diffraction pattern analysis (XRD). The microstructure for the sintered samples were characterized using a Scanning Electronic Microscope (SEM). And the piezoelectrical properties ($k_{p}$ and $Q_{m}$) of the sintered samples was measured using HP 4194A impedance analyzer.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.6
• /
• pp.359-363
• /
• 2017

A slotted implantable patch antenna with microstrip feeding is proposed for industrial, scientific, and medical band applications. The result is verified by implanting the antenna in animal tissue. Further, by varying the ground width and introducing a defect into the ground structure, the antenna becomes applicable for worldwide interoperability for microwave access operations. A simulation is performed using Empire XCcel software. An Agilent vector network analyzer is used for analyzing the return loss performance. Simulated and measured results are compared. Antennas with and without defected ground structure both have key advantages including low profile, desirable return loss, good impedance matching and required bandwidth.