• 시멘트
• /
• 통권64호
• /
• pp.11-16
• /
• 1976

암석 파쇄시 최대의 효과를 얻기 위해서는 암석의 물리적, 화학적 특성 및 size 등을 고려하여 최적의 crusher를 선택해야 함을 감안하여 crusher의 일종인 impact crusher의 구조 및 파쇄원리, 파쇄효과, 경제성 검토결과 등을 수록, crusher의 선택 및 광산 운영에 참고케 하고자 한다.

• 드라이브 ㆍ 컨트롤
• /
• 제16권2호
• /
• pp.1-7
• /
• 2019

Jaw crusher is a device that breaks rock collected from mines or quarries to produce aggregates of the size desired by user. A representative method for measuring load is to measure them by attaching force sensors directly to the part where the load is generated. However, the direct method has many limitations such as high-impact loads generation in equipment or space constraints, sensor capacities and costs. Therefore, Transfer Path Analysis (TPA) was used to indirectly measure impact loads by attaching acceleration sensors. In this study, both direct and TPA methods were used to measure the impact load of Jaw crusher. This study finally quantifies the impact of the load generated by the Jaw crusher using direct method and TPA method, and comparing the impact load measured calculated the derive the error rate.

• 한국구조물진단유지관리공학회 논문집
• /
• 제9권3호
• /
• pp.93-100
• /
• 2005

본 연구는 con crusher와 impact crusher로 생산된 골재의 입형과 크기에 따른 포러스 콘크리트의 특성을 파악하는데 있으며, 이를 위한 실험인자로는 골재의 입형과 크기, 물시멘트비 그리고 페이스트 굵은골재비이다. 연구결과, 포러스 콘크리트는 impact crusher로 생산한 골재를 사용할 경우 경제성은 물론 물리적 특성이 향상되었다. 또한, 포러스 콘크리트의 투수계수와 압축강도는 공극율과 매우 높은 상관성을 보이며, 공극율의 함수로서 제시할 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 추계 학술논문 발표대회 논문집
• /
• pp.83-86
• /
• 2006

This study investigates engineering properties of concrete using recycled coarse aggregated manufactured by bar-crusher. Test showed that Bar-crusher(S) had more effective results at fresh state than cone-crusher(C) and impact-crusher(I). In case of specimens manufactured by S, increase of spindle velocity, incorporating ratio of recycled aggregate and maximum size of aggregate inclined fluidity. As for the hardened concrete, compressive strength of specimens by C or I exhibited lower value than that of S. In addition, specimens using recycled aggregate manufactured by 400rpm and 500rpm of spindle velocity showed less than 10% reduction rate of strength, which is not significant reducing value. It is found that 500rpm of the spindle velocity had the best strength performance, while 600rpm was the worst. Strength value of specimens decreased as incorporating ratio of recycled aggregate inclined, but the strength value of most specimens exhibited less than 10% of reducing rate, assuming favorable result, only at less than 25% incorporating ratio of recycled aggregate.

• 드라이브 ㆍ 컨트롤
• /
• 제19권4호
• /
• pp.77-84
• /
• 2022

The aims of this study was to estimate transfer force delivered to cone crusher housing and contribution of force transmission. The rock crushing condition caused vibrations in the cone crusher housing, which were experimentally measured, and frequency response functions (FRF) were also found through modal impact tests. Vibration data and frequency response functions were applied to the transfer path analysis (TPA) model. Next, transfer forces delivered to the cone crusher housing were quantified via the TPA method. Contribution of force transfer was also analyzed based on force estimation results. Finally, this study describes basic concepts and components of the TPA method and reviews its applicability to rotating machinery that experiences impact vibrations and forces.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.443-446
• /
• 2005

Recently, according to increase use of concrete which is the main material of construction, the natural aggregate of good quality is more and more decreased. Most of all, among the concrete materials, the development of alternation materials of sand is urgently needed. In this study, investigating the production equipment and the sample of crushed sand company and analyzing properties of sand, manufactured mortar by the KS to use crushed sand as the fine aggregate of concrete material. The experiment result is as follows. 1. The density, an absorptivity, and the amount of 0.08mm passage ratio of crushed sand, and the mortar used crushed sand satisfied KS. The mechanical results is similar to sea sand. 2. The crushed sand which used impact crusher instead of cone crusher for 3rd or 4th crusher was similar properties to sea sand, so it is judged that impact crusher has high effect of particle shape improvement of crushed sand.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.509-512
• /
• 2006

In this study, the quality properties of recycled coarse aggregate, manufactured by the barcrusher, were compared to that of aggregate, manufactured by conservative systems. Test showed that recycled coarse aggregate, manufactured by the bar-crusher, had higher density and shape index, and exhibited lower absorption and abrasion ratios, compared with a con-crusher and an impact-crusher. This is due to the peeling-off effect of mortar, attached on recycled aggregate and the improved round shape of that.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.841-844
• /
• 2002

The vertical impact crusher is the machine which could produce artifical sand similar to natural aggregates in the site of guarry and pits. FEM was used to analyse the stress and strength of the machine at high rotational speed. The test specimen was made from the same material as the shaft and tension tests were conducted. The shaft under extreme conditions was analysed to determine maximum stress level and its location from the results. The maximum level of stress and its location could be predicted.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2004년도 춘계학술대회
• /
• pp.211-220
• /
• 2004

The vertical impact crusher is the machine which could produce artifical sand similar to natural aggregates in the site of guarry and pits. FEM was used to analyse the stress and strength of the machine at high rotational speed. The test specimen was made from the same material as the shaft and tension tests were conducted. The Shaft under extreme conditions was analysed to determine maximum stress level and its location from the results. The maximum level of stress and its location could be predicted.

• 자원리싸이클링
• /
• 제27권3호
• /
• pp.86-92
• /
• 2018

건설폐기물 발생량은 매년 꾸준하게 상승하고 있으며 재활용촉진 법이 재정되어있지만 콘크리트-시멘트페이스트 간의 단체분리 저하로 인해 높은 흡수율과 낮은 밀도로 순환골재 품질 기준에 제시되어 있는 콘크리트용 순환골재로서 사용되기 어려운 실정이다. 따라서 본 연구에서는 순환골재의 품위 향상에 필수적인 몰타르 제거를 위하여 다단형 임팩트 크러셔를 사용하였다. 장비의 특성을 분석하는데 있어서 전산 모사 방법인 DEM (Discrete Element Method)를 이용하여 영상 분석을 이용한 내부 입자의 거동 특징과, 투입 입자-장비의 각 부분에 발생하는 에너지의 스펙트럼을 분석하였다. 내부벽, 가이더 및 임펠러의 힘의 크기를 발생하는 횟수에 따라 스펙트럼을 생성하여 효과적인 분석이 가능하였다. 효과적인 박리현상을 발생시키기 위하여, 저에너지 그룹의 충돌 횟수(L)와 파분쇄를 발생시키는 고에너지 그룹의 충돌 횟수(H)의 비율을 토대로 회전속도 900RPM의 조건이 적절함을 확인하였다.