• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.10
• /
• pp.1529-1535
• /
• 2012

This paper presents the application algorithm for speed control of Switched Reluctance Motor. The conventional PI controller has been widely used in industrial applications. But it is very difficult to find the optimal PI control gain. Fuzzy control does not need any model of plant. It is based on plant operator experience and heuristics. The proposed fuzzy logic modifier increases the control performance of conventional PI controller. Simulation and experimental results show that the proposed fuzzy control method was superior to the conventional PI controller in the respect of system performance. The experiments are performed to verify the capability of proposed control method on 6/4 salient type SRM.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.615-619
• /
• 2000

This paper presents an implementation of digital motion control system of Surface Permanent-Magnet Synchronous Motor(SPMSM) vector drives with a direct torque control(DTC) using the 16bit DSP TMS320F240 The DSP controller enable enhanced real time algorithm and cost-effective design of intelligent control for motors which can be yield enhanced operation fewer system components lower system cost increased efficiency and high performance The system presented are stator flux and torque observer of stator flux feedback model that inputs are current and voltage sensing of motor terminal and angle for a low speed operating area two hysteresis band controllers an optimal switching look-up table and IGBT voltage source inverter by using fully integrated control software. The developed control system are shown a good motion control response characteristic results and high performance features using 1.0Kw purposed servo drive SPMSM.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.3
• /
• pp.43-52
• /
• 2020

In this study, the Buckling restrained braces reinforced with engineering plastics that can compensate for the disadvantages in the manufacturing process of the existing buckling restrained brace. The proposed PC-BRB was fabricated to evaluate the reinforcement effect by carrying out a structural performance test and a full-scale two-layer frame test through cyclic loading test. As a result of PC-BRB's incremental and cyclic loading test, stable hysteresis behavior was achieved within the target displacement, and the compressive strength adjustment coefficient satisfied the recommendation. As a result of the real frame experiment, the strength of the reinforced specimen increased compared to the unreinforced specimen, and the ductility and energy dissipation increased.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.616-621
• /
• 1989

This paper describes newly developed high performance control system for vector controlled induction motor. In order to realize this system, the authors are adopted the current controlled PWM inverter with hysteresis controller. A priori knowledge of the motor parameters is need in order to implement indirect vector control on induction motor drive systems where the position of rotor flux is estimated. This paper presents some of the relevant mathematics necessary to study parameter sensitivity in induction motor servo system. Simulation results demonstrate the predicted performance.

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.79-84
• /
• 2000

This paper presents an implementation of digital position control system for an induction motor vector drives by a direct torque control(DTC) using the 16bit DSP TMS320 F240. The DSP controller enable enhanced real time algorithm and cost-effective design of intelligent controller for motors which can be yield enhanced operation, fewer system components, lower system cost, increased efficiency and high performance. The system presented are stator flux and torque observer using current model that inputs are current sensing of motor terminal and rotor angle for a low speed operating area, two hysteresis controller, optimal switching look-up table, and IGBT voltage source inverter by fully integrated control software. The developed control system are shown a good motion control response characteristic results and high performance features using 2.2Kw general purposed induction motor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.677-681
• /
• 2013

Apart from the deposition of alignment layer, alignment process needs to be involved for alignment of liquid crystal (LC) molecules. To simplify manufacturing process, several method were used such as rubbing, ion-beam irradiation, UV irradiation, and lithography. But, eventually it needs another treatment for LC alignment. Here, we suggested Si induced polyimide (PI) alignment layer at low temperature. Using this method, we are able to eliminate the alignment process and found that the alignment and electro-optic performance are much better than that of the rubbed PI LC cells. Compared to the rubbed PI cells, the response time was decreased by 70% and C-V characteristics have hysteresis-free.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.68.5-68
• /
• 2002

For the performance test of rechargeable electric tools, it is necessary to test under the same condition as the actual operation condition. They are necessary to control the load torque and to acquire the test data with a computer, and it should be convenient to fix the tool on the test equipment for rechargeable electric tools. It consists of torque loading parts, sensing parts and control software. Two hysteresis brakes, connected serially with flexible coupling, were applied to control the load for the test. The sensing part consists of a torque sensor, a rpm detector and a power analyzer. The torque and the rpm were measured in order to calculate the output of the rechargeable electric...

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.5
• /
• pp.22-29
• /
• 1981

An ion sensitive field effect transistor employing a special HCI heat treatment for the gate oxide layer along with tungsten metallization and multilayer encapsulation using fumed silica epoxy mixture was fabricated and its performance characteristics have been investigated. A theoretical model for the device operation is discussed, and it is shown that the experimental results are in good agreement with the theory. The fabricated device has excellent performance characteristics showing the fast response, long operation-life, small pH hysteresis, high sensitivity, etc. Especially, its stability has been greatly improved.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.296-298
• /
• 1997

The performance of thin film pressure sensors with polyimide and silicon oxide as a insulating layer between the stainless steel diaphragm and the Cu-Ni strain gauges is presented. The polyimide was spun on the stainless steel diaphragm and cured in an oven. The silicon oxide was deposited by rf sputtering. The thin film pressure sensor with silicon oxide as a insulating layer showed a better nonlinearity and a lower hysteresis.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.4
• /
• pp.538-545
• /
• 2008

This paper attempts to summarize torque control strategy for high performance SR drive. There are primarily two strategies for torque control. One method is direct torque control, which uses the simple control scheme and hysteresis controller to reduce the torque ripple. Another method is indirect torque control, which uses the complicated algorithms or simple distribution function to distribute each phase torque and obtain current command. The current controller is used to control phase torque by a given current command. In order to compare these two strategies of torque control, five torque control methods are introduced. The advantages and disadvantages of each method are presented. At last, they are verified by some simulations and experimental results.