• Journal of Soil and Groundwater Environment
• /
• v.8 no.4
• /
• pp.1-11
• /
• 2003

In order to measure aperture variation dependent on normal stress and to characterize on relationship between aperture variation and hydraulic conductivity this study measured apertures of rock fractures under a high resolution confocal laser scanning microscope (CLSM) with application of five stages of uniaxial normal stresses. From this method the response of aperture can be continuously characterized on one specimen by different loads of normal stress. The results of measurements showed a rough geometry of fracture bearing non-uniform aperture. They also revealed different values of aperture variations according to the load stages on each position along a fracture due to the fracture roughness. Laboratory permeability tests were also conducted to evaluate the changes of permeability coefficients related to the aperture variations by different loads. The results of permeability tests revealed that the hydraulic conductivity was not reduced at a fixed rate with increase of normal load. Moreover, the rates of aperture variations did not match to those of hydraulic conductivity. The hydraulic conductivity calculated in this study did not follow the cubic law, representing that the parallel plate model is not suitable to express the fracture geometry corresponding to the results of aperture measurements under the CLSM.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.2
• /
• pp.132-147
• /
• 1996

The optimal design of floating type fisheries facilities in the open sea is demanded considering with the severe hydrodynamic forces on floating body, mooring tension and holding force of anchor. For conserving the facilities in most effective state, design and selection of anchor system is one of the most important fundamental subject. To enhance the design procedure of anchor system the holding forces of anchor are investigated by the hydraulic model test and are compared with the typical conventional results for various anchors. Applicability of previous estimation methods of holding force are checked and holding mechanism of anchor is discussed. Using the results a new computational concept of holding force is suggested considering mainly the effects of passive soil pressure (resistance), steady soil pressure, and surface friction etc. The new estimation method is proved as a feasible one by comparing the results of hydraulic model experiments. Applicability of various anchors to the anchor system on open sea fisheries structures is comprehensively reviewed using the present model tests and previous study results in the viewpoint of economy, construction and stability etc. Using the results, fundamental anchoring system design procedures are suggested to apply huge marine ranching complex with increase of the holding capacity of anchor under the optimum cost.

• Structural Engineering and Mechanics
• /
• v.16 no.3
• /
• pp.241-257
• /
• 2003

The first seismically isolated structure in Taiwan was completed in early 1999. Seven new bridges of the Second National Freeway located at Bai-Ho area, a region which is considered to be of high seismic risk, have been designed and constructed with lead-rubber seismic isolation bearings. Since this is the first application of seismic isolation method to the practical construction in Taiwan, field tests were conducted for one of the seven bridges to evaluate the assumptions and uncertainties in the design and construction. The test program is composed of ambient vibration tests, forced vibration tests, and free vibration tests. For the free vibration tests, a special test setup composed of four 1000 kN hydraulic jacks and a quick-release mechanism was designed to perform the function of push-and-quick release. Valuable results have been obtained based on the correlation between measured and analytical data so that the analytical model can be calibrated. Based on the analytical correlation, it is concluded that the dynamic characteristics and free vibration behavior of the isolated bridge can be well captured when the nonlinear properties of the bearings are properly considered in the modeling.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.26-31
• /
• 2009

Three Lox pumps and one fuel pump are manufactured for turbopump real-propellent tests and water tests of the pumps are performed in order to estimate the performance characteristics of the pumps. According to the test results, the test region(flow ratio, cavitation number) of the pumps at the water tests cover the operating region at the real-propellent tests and also all the pumps satisfy the design requirement. The head of the Lox pumps shows a 2% difference among them due to the internal geometry, but the efficiency and overall cavitation performance are almost same. It is found that the fuel pump has a similar head and efficiency compared with the previous model of the same internal geometry, while it has a little inferior cavitation performance.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.3
• /
• pp.74-80
• /
• 1993

Runoff simulation tests to investigate the flow mechanics of nonsuomerged overland flow in a natural grass intervening land system were condueted and a modified kinematic wave overland runoff model developed by Choi et al. (1993) was verified. Nonhomogeneity and heterogeneity of the soil, slope, local topography, infiltration, grass density, and the density and activity of the soil microhes and wild animals were the major factors affecting the flow. Streamlines were disturbed by grass stems and small concentrated flows due to the disturbed streamlines and local topography were observed a lot. Relatively larger concentrated flows were observed where bundles of grass were dominant than where individual grasses were growing. Predicted hydrographs were agreed verv well with measured hydrographs. Since the modified model considers grass density in computing flow depth and hydraulic radius, it can be better than existing kinematic wave model if it were used to route nonpoint source pollutant attenuation processes in many grass intervening land systems.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.37 no.1
• /
• pp.37-48
• /
• 1995

The TIDE, nonlinear finite element model for the simulation of tidal analysis in a shal- low ooastal area was tested for its applicability at the Saemankeum day. Calibration of the TIDE model has been carried out using the six observed field data collected at five locations within the region for tidal velocity. Verification tests have been done using the six observed field data and four data o- tained from the hydraulic model test for the tidal velocity and elevation. Since the simula- tion results for the tidal elevation at Kunsan outer port by the TIDE model are well agreed with the results from the tidal table for one month, it is proved that the TIDE model may be used effectively to predict the tidal movement in the Saemankeum bay for a longer period.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.47-54
• /
• 2003

The rotating of rotatory unit with its structural unbalance mass and laundry is making the main vibration problem in a vertical axis washing machine. For reducing vibration problem total washing system hung on the case by its suspension system which is constitute of spring, damper and suspension bar and hydraulic balancer is attached at the upper rim of spin basket. In this paper, we make the dynamic model of washing system of its rigid body motions by 6 degree of freedoms. Hydraulic balancer is modeled by one degree of freedom like auto ball balancer. Elastic motions of washing system have found by method of analytic, experimental and FEM. And we consider first bending mode of each suspension bar and first circumferential mode of assy tub. So, the total washing system is modeled by 12 degree of freedoms. Equations of motion for total washing system have derived, and we perform the dynamic simulation tests.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.201-204
• /
• 2008

Vortex and swirl occurring in a pump suction intake sump normally reduce the performance and disturb the safe operation of the circulation water pump in thermal power plants. This paper presents a case study of one particular intake sump design via a CFD analysis and a hydraulic model testing. The physical experiments and numerical analysis were performed under two flow and three level variation conditions. The vortex patterns around the pump suction pipe have been predicted by a commercial CFD code with the k-${\varepsilon}$ model. The model tests were conducted on a 1/10 model for a practical intake sump. The location, number and general pattern of the free surface vortex and submerged vortex predicted by CFD simulation were found to be a good agreement with those observed in the model testing.

• Proceedings of the Korean Society of Coastal and Ocean Engineers Conference
• /
• 2009.10a
• /
• pp.180-183
• /
• 2009

월파조건에서 직립벽을 따른 연파특성에 대한 실험을 수행하고 그 결과를 비교하였다. 제체전면을 따른 파고분포를 살펴보면, 상대여유고에 따른 파고변화는 어느 정도 나타났다. 제체 직각 방향으로의 결과에서 상대파고의 감소는 연파의 폭범위내에서 나타나는 것을 확인할 수 있었다. 향후 보다 자세한 분석과 월파량과 연계한 분석을 수행할 예정이다.

• Journal of the Korean Geophysical Society
• /
• v.6 no.4
• /
• pp.221-230
• /
• 2003

Many hydraulic structures are damaged by under flood flow and storm waves year after year. Many cases of dike and breakwater failure are caused by the suck out of sand from behind the revetment. This type of failure will be in close relation to the dynamic behavior of sand bed around the revetment. In this paper, from this point of view we investigated the basic characteristics of such sand movement by small model tests and tried to explanation the hydro- and soil mechanical mechanism of this phenomenon theoretically.