• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.200-211
• /
• 2017

Conventional boost-full-bridge and boost-hybrid-bridge two-stage inverters are widely applied in order to adapt to the wide dc input voltage range of photovoltaic arrays. However, the efficiency of the conventional topology is not fully optimized because additional switching losses are generated in the voltage conversion so that the input voltage rises and then falls. Moreover, the electrolytic capacitors in a dc-link lead to a larger volume combined with increases in both weight and cost. This paper proposes a higher efficiency inverter with time-sharing synchronous modulation. The energy transmission paths, wheeling branches and switching losses for the high-frequency switches are optimized so that the overall efficiency is greatly improved. In this paper, a contrastive analysis of the component losses for the conventional and proposed inverter topologies is carried out in MATLAB. Finally, the high-efficiency under different switching frequencies and different input voltages is verified by a 3 kW prototype.

• ETRI Journal
• /
• v.39 no.1
• /
• pp.62-68
• /
• 2017

In this paper, we present the design and characterization analysis of a cascode GaN field-effect transistor (FET) for switching power conversion systems. To enable normally-off operation, a cascode GaN FET employs a low breakdown voltage (BV) enhancement-mode Si metal-oxide-semiconductor FET and a high-BV depletion-mode (D-mode) GaN FET. This paper demonstrates a normally-on D-mode GaN FET with high power density and high switching frequency, and presents a theoretical analysis of a hybrid cascode GaN FET design. A TO-254 packaged FET provides a drain current of 6.04 A at a drain voltage of 2 V, a BV of 520 V at a drain leakage current of $250{\mu}A$, and an on-resistance of $331m{\Omega}$. Finally, a boost converter is used to evaluate the performance of the cascode GaN FET in power conversion applications.

• Journal of Power Electronics
• /
• v.11 no.1
• /
• pp.1-9
• /
• 2011

This paper describes a two quadrant bidirectional soft switching converter for ultra capacitor interface circuits. The total efficiency of the energy storage system in terms of size and cost can be increased by a combination of batteries and ultra capacitors. The required system energy is provided by a battery, while an ultra capacitor is used at high load power pulses. The ultra capacitor voltage changes during charge and discharge modes, therefore an interface circuit is required between the ultra capacitor and the battery. This interface circuit must have good efficiency while providing bidirectional power conversion to capture energy from regenerative braking, downhill driving and the protecting ultra capacitor from immediate discharge. In this paper a fully soft switched two quadrant bidirectional soft switching converter for ultra capacitor interface circuits is introduced and the elements of the converter are reduced considerably. In this paper, zero voltage transient (ZVT) and zero current transient (ZCT) techniques are applied to increase efficiency. The proposed converter acts as a ZCT Buck to charge the ultra capacitor. On the other hand, it acts as a ZVT Boost to discharge the ultra capacitor. A laboratory prototype converter is designed and realized for hybrid vehicle applications. The experimental results presented confirm the theoretical and simulation results.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.10
• /
• pp.77-83
• /
• 2010

In this paper, the noise of HEV(hybrid electric vehicle)-relay module during the turn-on and turnoff switching is experimentally analyzed and an effective method is proposed to reduce the impact noise. First, enclosure methods of 100A relay part with urethane and silicon are tested to find out a better material to isolate the noise. This result shows that the urethane is a better for the noise isolation of relay, so the relays enclosed by urethane are installed in the relay module. Second, the noise of HEV-relay module is analyzed experimentally to identify the noise generation mechanism. From this result, it is found that the vibration transmitted to battery pack through bolt generates the structural borne noise with the frequency band of 200~2000 Hz, which is more serious when the switch is turned off. Finally, the direction of switching and the joint structure are modified in order to isolate the vibration transmitted to battery back. Both methods are very effective to reduce the switching noise.

• Journal of Satellite, Information and Communications
• /
• v.5 no.2
• /
• pp.97-103
• /
• 2010

In this paper, we present an efficient design scheme based on analysis of design requirements and considerations of baseband packet switch for S-band satellite/terrestrial hybrid multi-beam satellite communication systems. To establish design requirements and considerations, we analyze required functions of baseband packet switch, specifications of multi-beam satellite communications, communication services and performance requirements. And also we analyze and compare conventional layer-2 and layer-3 satellite baseband packet switching techniques, packet switching protocols and packet switch architectures, to apply from analyzed results. Finally, we propose a hardware design scheme of MPEG based layer-2 baseband packet switch using analyzed results.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.907-921
• /
• 2019

This paper presents two advanced hybrid pulse-width modulation (PWM) strategies for multilevel inverters (MLIs) that provide both common-mode voltage (CMV) elimination and current ripple reduction. The first PWM utilizes sequences that apply one switching state at the double ends of a half-carrier cycle. The second PWM combines the advantages of the former and an existing four-state PWM. Analyses of the harmonic characteristics of the two groups of switching sequences based on a general switching voltage model are carried out, and algorithms to optimize the current ripple are proposed. These methods are simple and can be implemented online for general n-level inverters. Using a three-level NPC inverter and a five-level CHB inverter, good performances in terms of the root mean square current ripple are obtained with the proposed PWM schemes as indicated through improved harmonic distortion factors when compared to existing schemes in almost the entire region of the modulation index. This also leads to a significant reduction in the current total harmonic distortion. Simulation and experimental results are provided to verify the effectiveness of the proposed PWM methods.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.815-818
• /
• 1998

The Insulated Gate Bipolar Transistor has the characteristics of MOSFET and BJT. The characteristics of proposed device exhibit high speed switching, the voltage controlled property, and the low ON resistance. This hybrid device has been used and developed continuously in the power electronic engineering field. We can simulate many IGBT circuits, such as the motor drive circuit, the switching circuits etc, with PSpice. However, some problems in PSpice is that the IGBT is old-fashioned and is very difficult to get it. In this paper, the IGBT in PSpice is considered as the basic structure. We changed the valuse of base width, gate-drain overlaping area, device area, and doping concentration, then calculated MOS transconductance, ambipolar recombination lifetime etc. Using this resultant parameter, we could predict the transient response characteristicsof IGBT, for examplex, voltage overshoot, the rising curve of voltage, and the falling curve of current.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.261-265
• /
• 2001

In this paper, a current-source type parallel indudor compensated load resonant high-frequency soft switching inverter using IGBTs for driving the newly-produced silent discharge type ozone generating tube and excimer lamp for UV generation which incorporate a single switched capacitor resonant snubber between the port in DC busline side is presented, together with its pulse modulated unique output power regulation characteristics.

• Journal of Industrial Technology
• /
• v.13
• /
• pp.89-96
• /
• 1993

In this paper, an OPS(Optical Protection Socket) unit is designed and prototyped for the application in the optical CPN(Customer Premises Network). The OPS unit, which plays an important role in the CPN for the enhanced network reliability, is consisted of $1{\times}2$ optical fiber splitter, combiner, and $1{\times}1$ optical switch to be a hybrid-typed unit. Various considerations, about power burget and optical information loss have given the most practical design for OPS. From the measurement of the realized OPS unit, it has proved such as the pertinent switching delay time with minimum data loss, the perceptive ability on the ONU degradation, the switching ability on the ONU malfunction.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.2
• /
• pp.324-330
• /
• 2013

The dispersion of acoustic noise during the turn-on and turn-off switching of HEV(hybrid electric vehicle) relay was experimentally analyzed to identify the reason for the dispersion of noise level. An effective method was proposed to reduce the dispersion of noise level. First, a method to wrap the side of moving core with a tape was adopted to reduce the transverse vibration. It enabled the moving core to make a consistent motion and reduce the dispersion of noise level from switching operation of relay. Second, the dispersion of noise level from vibration transmission of parts such as the outer frame and yoke caulking part of relay were tested to find out main sources. From this result, it was identified that the yoke caulking part made inconsistent transient vibration and noise dispersion.