• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.2
• /
• pp.63-70
• /
• 2003

In this paper, an MFC (Mass Flow Controller) which is widely used in many semiconductor manufacturing processes for controlling the mass flow rate of a gas is designed and implemented using the PIC 16F876 of Microchip, Inc. The MFC implemented in this thesis has the form of hybrid-type, i.e., the mixed-type of the analog-type MFC, which has many problems such as low accurary, and digital-type MFC, which use an expensive DSP (Digital Signal Processor) and an ADC (Analog to Digital Convertor) with high precision. The MFC is consists of the sensor unit, the control unit and the actuator unit, and it has used the automatic calibration algorithm and the reference table method for the improvement of the performance.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.106-110
• /
• 2012

Oblique angle deposition (OAD) is a physical vapor deposition where incident vapor flux arrives at non-normal angles. It has been known that tilting the substrate changes the properties of the film, which is thought to be a result of morphological change of the film. In this study, OAD has been applied to prepare single and multilayer TiN films by cathodic arc deposition. TiN films have been deposited on cold-rolled steel sheets and stainless steel sheet. The deposition angle as well as substrate temperature and substrate bias was changed to investigate their effects on the properties of TiN films. TiN films were analyzed by color difference meter, scanning electron microscopy, nanoindenter and x-ray diffraction. The color of TiN films was not much changed according to the deposition conditions. The slanted and zigzag structures were observed from the single and multilayer films. The relation between substrate tilting angle (${\alpha}$) and the growth column angle (${\beta}$) followed the equation of $tan{\alpha}=2tan{\beta}$. The indentation hardness of TiN films deposited by OAD was low compared with the ones prepared at normal angle. However, it has been found that $H^3/E^2$ ratio of 3-layer TiN films prepared at OAD condition was a little higher than the ones prepared at normal angle, which can confirm the robustness of prepared films.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.6
• /
• pp.590-596
• /
• 2020

In the island areas where system connection with the commercial power grid is difficult, it is quite important to find a method to efficiently manage energy produced with independent microgrids. In this paper, a prosumer management system for P2P power transaction was realized through the testing the power meter and the response rate of the collected data for the power produced in the small-scale microgrids in which hybrid models of solar power and wind power were implemented. The power network of the microgrid prosumer was composed of mesh structure and the P2P power transaction was tested through the power meter and DC power transmitter in the off-grid sites which were independently constructed in three places. The measurement values of the power meter showed significant results of voltage (average): 380V + 0.9V, current (average): + 0.01A, power: 1000W (-1W) with an error range within ±1%. Stabilization of the server was also confirmed with the response rate of 0.32 sec. for the main screen, 2.61 sec. for the cumulative power generation, and 0.11 sec for the power transaction through the transmission of 50 data in real time. Therefore, the proposed system was validated as a P2P power transaction system that can be used as an independent network without transmitted by Korea Electric Power Corporation (KEPCO).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.52 no.2
• /
• pp.159-172
• /
• 2019

This study investigated the effects of dietary monobasic potassium phosphate (MKP) on the growth of the far eastern catfish Silurus asotus and four leafy vegetables in a hybrid biofloc technology aquaponic system. To an experimental diet containing 45% protein and 7% lipid, 1, 2, 3 or 4% MKP was added and was designated as MKP1, MKP2, MKP3, and MKP4, respectively. The optimum MKP levels were determined for the growth of fish and four leafy vegetables over 10 weeks. After the 10-week feeding trial, weight gain, feed efficiency, specific growth rate and protein efficiency ratio were higher in the fish groups fed MKP2 and MKP3 than in the other groups (P<0.05). The growth of the four leafy vegetables was also higher in the fish groups fed MKP2 and MKP3. Water quality [dissolved oxygen, pH, water temperature, electrical conductivity, turbidity, total ammonia nitrogen (TAN), $NO_2-N$, $NO_3-N$ and $PO_4-P$] was measured six times a week using a portable water quality meter and reagent measurements. The TAN (4.58-20.40 mg/L), $NO_3-N$ (24.12-52.40 mg/L) and $PO_4-P$ (20.38-48.48 mg/L) levels increased with time, while the $NO_2-N$ level remained below 0.1 mg/L throughout the study.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.8 no.6
• /
• pp.8-16
• /
• 1971

This paper describes the transistorized linear counting ratemeter which can be uses to indicate on the meter or record the counting rates of the nuclear radiations produced from the atomic reactor or from the radio isotopes. Tte feature of this ratemeter is the use of the transistor chopper for good stabilization. At the input stage of the a. c. amplifier a composite emitter follower buffer stage has been used to give the high input impedance. A hybrid parameter equivalent circuit was modeled for the analysis of this buffer stage. The counting rates can be linearly measured from few CPS up to 100KCPS in 4 ranges. The resolution is less than 0.5$\mu$sec and the output drift at the room temperature with 7-hour continuous operation is in the order of $\pm$0.5$\mu$A.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.933-938
• /
• 2014

The combined method utilizing airborne LiDAR and GIS data is suggested to extract 3-dimensional hybrid city model including roads and buildings. Combining the two types of data is more efficient to estimate the elevations of various types of roads and buildings than using either LiDAR or GIS data only. This method is particularly useful to model the overlapped roads around the so called spaghetti junction. The preliminary model is constructed from the LiDAR data, which can give wrong information around the overlapped parts. And then, the erratic vertex points are detected by imposing maximum vertical grade allowable on the elevated roads. For the purpose of efficiency, the erratic vertex points are corrected through linear interpolation method. To avoid the erratic treatment of the LiDAR data on the facades of buildings 2 meter inner-buffer zone is proposed to efficiently estimate the height of a building. It is validated by the mean value (=5.1%) of differences between estimated elevations on 2 m inner buffer zone and randomly observed building elevations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.79-82
• /
• 2003

a-Se film is known as promising medical X-ray detector material but a-Se as dopanted Tellurium is not available in X-ray detectors. a-Se thick film was grown by vacuum thermal evaporator to $3{\mu}m$ thickness. The characteristics of thick films were analyzed by XRD, U-V Meter, and SEM measurements. Te composition is 0.1, 0.3, 0.5, 0.7g. This paper is fundmental data for phosphor layer's essential parameter that selenium have absorption wavelength along to various Te concentration rate.

• Journal of the Korean association of regional geographers
• /
• v.12 no.4
• /
• pp.496-507
• /
• 2006

A hybrid approach integrating both high-resolution and hyperspectral data sets was used to map vegetation cover of a coastal lowland area in the Hawaii Volcanoes National Park. Three common grass species (broomsedge, natal redtop, and pili) and other non-grass species, primarily shrubs, were focused in the study. A 3-step, hybrid approach, combining an unsupervised and a supervised classification schemes, was applied to the vegetation mapping. First, the IKONOS 1-m high-resolution data were classified to create a binary image (vegetated vs. non--vegetated) and converted to 20-meter resolution percent cover vegetation data to match AVIRIS data pixels. Second, the minimum noise fraction (MNF) transformation was used to extract a coherent dimensionality from the original AVIRIS data. Since the grasses and shubs were sparsely distributed and most image pixels were intermingled with lava surfaces, the reflectance component of lava was filtered out with a binary fractional cover analysis assuming that tile total reflectance of a pixel was a linear combination of the reflectance spectra of vegetation and the lava surface. Finally, a supervised approach was used to classify the plant species based on tile maximum likelihood algorithm.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.45-47
• /
• 2006

Lightweight design, safety, vibration, energy absorption capability can no longer achieve without adhesive bond joint. Base on those concepts and cost reduction, adhesive bond FEM model development has been done. The FEM analysis and experiments were conducted in this study. Crash condition is 143 Kg Hammer weight and unit meter Height. and then These test results were used to develop resonable FEM model. To estimate which FEM model is resonable, compare hybrid joint specimen experiment results with FEM analysis results. Conclusively this study achieves optimization bonding model related crash and adhesive bond jointed hat profile crash characters.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.9
• /
• pp.32-39
• /
• 2003

Pulse electrochemical machining process with high or low current density may produce a non-lustrous surface on workpiece surface. The usual polishing process to remove a black layer from the surface has been hand polish the part. But the milli-to-micro meter scale structure formed by the electrochemical machining process may be destroyed while polishing process. The application of ultra short voltage pulses based on the analysis of electrical double layer charging process allows high resolution electrochemical machining and polishing. This technique was based on the specific polarization resistance from the comparison of ideal and experimental potential variation during short voltage pulses.