• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.208-212
• /
• 1997

Shear-induced phase transformation behavior of chemically stabilized $\beta$-cristobalite was studied by the fiber push-out technique. To obtain the critical grain size for phase transformation, the hot-pressed polycrystalline $\beta$-cristobalite, which was used as the interphase between fiber and matrix, was annealed at $1300^{\circ}C$ for 10h. Two types of fibers, mullite and sapphire fiber, were used in this study. Debonding between mullite fiber and cristobalite interphase occurred at a critical load of 230 MPa. Static friction and fiber sliding were continuously followed by debonding. Shear-induced transformation induced cracks in the cristobalite interphase at the debonding stage. In the case of the sapphire fiber, the debonding occurred at a lower load of 180 MPa due to the residual stress in the interface caused by the difference in thermal expansion coefficients between the fiber and the cristobalite interphase. The load was insufficient for shear-induced phase transformation.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.224-228
• /
• 2000

Using a small amount of additives and amorphous Si₂N₂O powders, O-SiAlON ceramics have been hot-pressed and its microstructure and mechanical properties were investigated. Scandium oxide was demonstrated to be an effective densification additive for O-SiAlON. Amorphous Si₂N₂O was densified at relatively low temperatures and a microstructure with acicular grains was developed. Fine grains found in materials obtained from amorphous powders suggest that nucleation and crystallization of O-SiAlOH is relatively easy compared with the Si₃N₄-SiO₂reaction.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1996.05a
• /
• pp.177-184
• /
• 1996

We have developed a polysilicon semiconductor bridge (SCB) igniter which produces a plasma discharge that ignites explosive materials pressed against the bridge. Our experiments have demonstrated that the SCB produces a hot plasma that ignites explosives, when driven with a short, low energy peak. The SCB, a heavily-doped film, typically 100 $\mu\textrm{m}$long by 300 $\mu\textrm{m}$ wide 5 $\mu\textrm{m}$ thick, is 30 times smaller in volume than a conventional bridge. We described the SCB operation and processing, and the requirement of obtaining a plasma discharge in order to ignite the explosive material.

• Proceedings of the Safety Management and Science Conference
• /
• 2003.11a
• /
• pp.351-357
• /
• 2003

The optimum polymer gel electrolyte composition ratio was 23 : 66 : 11 wt% of P(VdF-co-HFP) : PVP =20 : 3), (PC: EC =44 : 22) and TEABF$_4$. And the optimal thickness of polymer gel electrolyte was 50 ${\mu}{\textrm}{m}$. The electrochemical characteristics result of unit cell were 31.41 Fig of specific capacitance, and 3.21$\times$10$^{-3}$ S/cm of ion conductivity. Ion conductivity of polymer gel electrolytes decreased according to added PVP through impedance analysis, and it was higher in 7 wt%, but electrochemical characteristics of unit cell were better in 3 wt% PVP. And for excellent ion conductivity of polymer gel electrolytes, the use of a thin layer electrolyte(20 $\mu\textrm{m}$) was an effective method, but with unit cell application, the best thickness was 50 $\mu\textrm{m}$. Unit cell showed higher capacitance and more stable electrochemical performance when hot pressed between polymer gel electrolyte and electrode. This results from enhancement of the physical contact between the electrode and the polymer gel electrolyte and good accessibility of the liquid electrolyte to the electrode surface.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1227-1228
• /
• 2006

The electrochemical properties of novel metal powders were investigated for the electrode materias of polymer electrolyte memebrane electrolysis. Two types of Pt black and $IrO_2$ powder electrodes were hot-pressed on the polymer electrolyte membrane to form membrane electrode assembly. The galvanodynamic polarization methode was used to characterize the electrochemical properties of both electrodes. From the experimental results, we concluded that the $IrO_2$ powder electrode exhibits better electrochemical performance than Pt black as cathode material for the electrolysis.

• The Korean Journal of Ceramics
• /
• v.1 no.4
• /
• pp.214-218
• /
• 1995

Partially stabilized zironia with magnesia (Mg-PSZ) is known as one of the toughest monolithic ceramics. However, the very large grain sizes obtained after sintering at a high solution-heat treatment temperature in the cubic region of the phase diagram limit the strength of this material rather modest. In this study fine-grained Mg-PSZ materials were fabricated by adding TiC particles as a dispersed phase. Samples were hot-pressed at $1750^{\circ}C$ and then annealed at $1420^{\circ}C$ for various times. Grain growth was retarded severely by the TiC particles resulting in grain sizes smaller by more than one order of magnitude than those of PSZ without TiC. The fine-grained microstructure lead to doubly-increased fracture strength while maintaining the same level of high fracture toughness as that of conventional Mg-PSZ without TiC particles.

• Journal of the Korean Ceramic Society
• /
• v.28 no.12
• /
• pp.1012-1018
• /
• 1991

SiC whisker-reinforced LAS matrix composites were developed by a mixed colloidal processing route. An optimization of processing conditions was made using the zeta potential data of silica, boehmite, and SiC whisker dispersions. Similarly, the SiC whisker-reinforced composites were also fabricated by the conventional sol-gel process using the hydrolysis-condensation reaction of relevant metal alkoxides. The composites fabricated by the mixed colloidal processing route were characterized by a uniform spatial distribution of SiC whisker throughout the matrix. The fracture toughness increased from 1.3 MPa.m1/2 for the LAS specimen to 5.0 Mpa.m1/2 for the hot-pressed composite (95$0^{\circ}C$ and 20 MPa for 20 min) containing 20 wt% SiC whisker. The increase in fracture toughness appears to result mainly from the crack deflection and the crack bridging by whiskers with some additional toughenings from the whisker pullout and the matrix prestressing mechanisms.

• Journal of the Korean Ceramic Society
• /
• v.28 no.5
• /
• pp.390-398
• /
• 1991

$\beta$-Sialon powder was prepared from Wando pyrophyllite by the carbothermic reduction and nitridation at 135$0^{\circ}C$ for 10 h nitrogen atmosphere. Amorphous silica prepared from Si(OC2H5)4 was added to Wando pyrophyllite powder in order to control the final Z value. Two different methods were applied for synthesis of $\beta$-sialon powders. In Process A, the amorphous silica prepared from Si(OC2H5)4 was admixed to Wando pyrophyllite powder. Process B was started from the mixture of Wando Y2O3 was added to the synthesized $\beta$-Sialon powders as a sintering aid, and the mixed powders were hot pressed at 175$0^{\circ}C$ for 120 min in nitrogen atmosphere under 30 MPa. Their mechanical properties were compared. The maximum values of M.O.R., hardness and KIC were 667 MPa, 16 GPa and 6.3 MN/m3/2, respectively, and they are the values obtained form $\beta$-Sialon ceramics prepared by process A of Z=0.5.

• Journal of the Korean Ceramic Society
• /
• v.30 no.11
• /
• pp.941-948
• /
• 1993

The powder mixture of Si3N4-AlN-Y2O3, Si3N4-AlN-CeO2 and Si3N4-AlN-Y2O3-CeO2 system was hot-pressed at 175$0^{\circ}C$ for 2h in N2 to prepare $\alpha$-Sialon ceramics. The mechanical property and oxidation behaviour of the prepared $\alpha$-Sialon ceramics were investigated. At 120$0^{\circ}C$, oxidation resistance was best for the Y2O3 added $\alpha$-Sialon ceramics and oxidation rate increased when the amount of CeO2 increased. But when the mixture of Y2O3 and CeO2 added $\alpha$-Sialon ceramics showed a good oxidation resistance. Fracture toughness of (Y2O3＋CeO2) added $\alpha$-Sialon ceramics was higher than Y2O3 added $\alpha$-Sialon ceramics.

• Journal of the Korean Ceramic Society
• /
• v.26 no.3
• /
• pp.402-408
• /
• 1989

$\beta$-Sialon powder was synthesized by the simultaneous reduction and nitridation of the mixed powder of Hadong kaolin and Kimcheon quartzite, using graphite as a reducing agent. The synthesized $\beta$-Sialon powder (Z=1) was hot-pressed at 175$0^{\circ}C$, for 90min under 30MPa in N2 atmosphere, after Yttria and YAG composition material were added as sintering agents. The effects of grain-boundary crystallization on high-temperature mechanical properties of $\beta$-Sialon ceramics were investigated. Strength degradation was observed at above 1,00$0^{\circ}C$ for the $\beta$-Sialon (Z=1)-8wt% Y2O3 composition, but it was not observed up to 1,20$0^{\circ}C$ for the $\beta$-Sialon-8wt% YAG composition which was annealed at 1,40$0^{\circ}C$ for 4 hours in N2 atmosphere. After the $\beta$-Sialon-8wt% YAG composition was annealed, the decrease of fracture toughness was observed.