• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.659-664
• /
• 1998

구조재료용 요업체로 널리 쓰이는 질화규소 요업체를 2단계 가스압 소결 방식에 의해 치밀화시켰을 때의 효과를 상압조절, 단순 가스압소결 또는 HIP 처리시와 비교하였다. 상압 소결시에는 $1800^{\circ}C$ 이상에서 분해가 일어나지만 질소 가스에 의한 가스압 소결시에는 소결 온도를 더 높일 수 있어서 ${\beta}-Si_3N_4$ 침상 조직의 발달을 이룰 수 있었다. 질소 가스압이 2MPa 정도이면 $1890^{\circ}C$까지도 상압소결시에 비해 분해가 현저히 억제될 수 있어서, 폐기공이 형성될 수 있는 단계까지는 분해만 억제시킬 수 있는 정도의 비교적 낮은 압력으로 치밀화시키고, 이어서 10MPa의 높은 압력을 가하는 소위 2단계 가스압 소결시 경도와 인성이 증진되는 것을 확인할 수 있었다.

• 한국주조공학회지
• /
• 제26권4호
• /
• pp.184-190
• /
• 2006

Presence of inclusions in Ti castings imparts detrimental effects on the mechanical performance of castings. However, actual inclusions do not occur very frequently and they are difficult to locate. As a result, acquirement of specimens for mechanical tests and thus in-depth research of the adverse influence of inclusions are challenging. To address this problem, artificial inclusion seeding methodology is developed to emulate actual inclusions in Ti investment castings. Firstly, to validate that this new methodology does not result in inherent mechanical property degradation, Ti specimens with machined, backfilled and HIPed holes are produced and compared to control (unaltered), cast Ti material. Fatigue test results indicate that this 'machine-and-HIP methodology without seeding' does not result in any fundamental mechanical property alteration, which would bias ensuing comparative results. Secondly, based on this result, validation of the artificially seeded inclusions being equivalent to 'as cast' inclusions is performed by comparing their fatigue behaviors. Test specimens created by the novel artificial inclusion seeding methodology are equivalent to Ti casting specimens containing actual cast-in inclusions, and an adverse effect of inclusions in investment castings is confirmed.

• 한국분말재료학회지
• /
• 제7권3호
• /
• pp.143-148
• /
• 2000

NiAl alloy powders were prepared by mechanical alloying method and bulk specimens were produced using hot isostatic pressing techniques. This study focused on the transformation behavior and properties of Ni-Al mechanically alloyed powders and bulk alloys. Transformation behavior was investigated by differential scanning calorimeter (DSC), XRD and TEM. Particle size distribution and microstructures of mechanically alloyed powders were studied by particle size analyzer and scanning electron microscope (SEM). After 10 hours milling, XRB peak broadening appeared at the alloyed powders with compositions of Ni-36at%Al to 40at%Al. The NiAl and $Ni_3Al$ intermetallic compounds were formed after water quenching of solution treated powders and bulk samples at $1200^{\circ}C$, but the martensite phase was observed after liquid nitrogen quenching of solution treated powders. However, the formation of $Ni_3Al$ intermetallic compounds were not restricted by fast quenching into liquid nitrogen. It is considered to be caused by fast diffusion of atoms for the formation of stable $\beta$(NiAl) phase and $Ni_3Al$ due to nano sized grains during quenching. Amounts of martensite phase increased as the composition of aluminium component decreased in the Ni-Al alloy, which resulted in the increasing damping properties.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1997년도 추계학술강연 및 발표대회 강연 및 발표논문 초록집
• /
• pp.7-7
• /
• 1997

During sintering of very porous green bodies, as obtained by compaction of hard powders - such as tungsten carbide or ceramics - or by injection moulding, important shrinkage occurs. Due to heterogeneous green density field, gravity effects, friction on the support, thermal gradients, etc., this shrinkage is often non-uniform, which' may induce significant shape changes. As the ratio of compact dimension to powder size is very high, the mechanics of continuum is relevant to model such phenomena. Thus numerical techniques, such as the finite element method can be used to simulate the sintering process and predict the final shape of the sintered part. Such type of simulation has much been developed in the last decade firstly for hot isostatic pressing and next for die compaction. Finite element modelling has been recently applied to free sintering. The simulation of sintering should be based on constitutive equations describing the thermo-mechanical behaviour of the material under any state of stress and any temperature which may arise within the sintering body. These equations can be drawn either from experimental data or from micromechanical models. The experiments usually consist in free sintering and sinter-forging tests. Indeed applying more complex loading conditions at high temperature under controlled atmosphere is delicate. Micromechanical models describe the constitutive behaviour of aggregates of spheres from the deformation of two-sphere contact either by viscous flow or grain boundary diffusion. Such models are not able to describe complex microstructure and mechanisms as observed in real materials but they can give some basic information on the formulation of constitutive equations. Practically both experimental and theoretical approaches can be coupled to identify the constitutive equations. Such procedure has been performed for modelling the sintering of compacts obtained by die pressing of a mixture of tungsten carbide and cobalt powders. The constitutive behaviour of this material during sintering has been described by a linear viscous constitutive model, whose functions have been fitted from results of free sintering and sinter-forging experiments. This model has next been introduced in ABAQUS finite element code to simulate the sintering of heterogeneous green compacts of various geometries at constant temperature. Examples of simulations are shown and compared with experiments.

• 한국분말재료학회지
• /
• 제27권4호
• /
• pp.311-317
• /
• 2020

In this study, the effects of Co content on the microstructure and Charpy impact properties of Fe-Cr-W ferritic/martensitic oxide dispersion strengthened (F/M ODS) steels are investigated. F/M ODS steels with 0-5 wt% Co are fabricated by mechanical alloying, followed by hot isostatic pressing, hot-rolling, and normalizing/tempering heat treatment. All the steels commonly exhibit two-phase microstructures consisting of ferrite and tempered martensite. The volume fraction of ferrite increases with the increase in the Co content, since the Co element considerably lowers the hardenability of the F/M ODS steel. Despite the lowest volume fraction of tempered martensite, the F/M ODS steel with 5 wt% Co shows the highest micro-Vickers hardness, owing to the solid solution-hardening effect of the alloyed Co. The high hardness of the steel improves the resistance to fracture initiation, thereby resulting in the enhanced fracture initiation energy in a Charpy impact test at - 40℃. Furthermore, the addition of Co suppresses the formation of coarse oxide inclusions in the F/M ODS steel, while simultaneously providing a high resistance to fracture propagation. Owing to these combined effects of Co, the Charpy impact energy of the F/M ODS steel increases gradually with the increase in the Co content.

• 방사성폐기물학회지
• /
• 제13권2호
• /
• pp.155-161
• /
• 2015

몰리브덴-99의 붕괴에 의해 생산되는 테크네튬-99m 은 방사선 진단에 중요한 역할을 담당하고 있다. 몰리브덴-99 는 주로 우라늄-235의 핵분열에 의해 생산되고 있으며, 이를 위해 고농축 우라늄 표적 또는 저농축 우라늄 표적이 연구로에서 조사된다. 현재는 고농축 우라늄의 사용에 따른 핵확산 문제를 저감하기 위해 저농축 우라늄 표적의 사용이 권장되고 있다. 본 연구는 몰리브덴-99 생산 시설의 계획 단계에서 방사성 폐기물 관리 전략을 정의하기 위하여 저농축 우라늄의 사용이 방사성 폐기물의 흐름에 미치는 영향을 분석하였다. 저농축 우라늄 표적 사용 시 우라늄 함유 폐기물의 부피가 6배 이상 증가하기 때문에 우라늄 고밀도 표적의 사용과 고온 정수압 압축법의 활용이 제안되었다.

• 한국분말재료학회지
• /
• 제24권3호
• /
• pp.202-209
• /
• 2017

A cold-work tool steel powder is used to fabricate 3-dimensional objects by selective laser melting using a high-pressure gas atomization process. The spherical powder particles form continuous carbide networks among the austenite matrix and its decomposition products. The carbides comprise Nb-rich MC and Mo-rich $M_2C$. In the SLM process, the process parameters such as the laser power (90 W), layer thickness ($25{\mu}m$), and hatch spacing ($80{\mu}m$) are kept fixed, while the scan speed is changed from 50 mm/s to 4000 mm/s. At a low scan speed of 50 mm/s, spherical cavities develop due to over melting, while they are substantially reduced on increasing the speed to 2000 mm/s. The carbide network spacing decreases with increasing speed. At an excessively high speed of 4000 mm/s, long and irregularly shaped cavities are developed due to incomplete melting. The influence of the scan pattern is examined, for which $1{\times}1 mm^2$ blocks constituting a processing layer are irradiated in a random sequence. This island-type pattern exhibits the same effect as that of a low scan speed. Post processing of an object using hot isostatic pressing leads to a great reduction in the porosity but causes coarsening of the microstructure.

• 한국분말재료학회지
• /
• 제26권6호
• /
• pp.508-514
• /
• 2019

In the development of advanced ceramic tools, material improvements and design freedom are critical in improving tool performance. However, in the die press molding method, many factors limit tool design and make it difficult to develop innovative advanced tools. Ceramic 3D printing facilitates the production of prototype samples for advanced tool development and the creation of complex tooling products. Furthermore, it is possible to respond to mass production requirements by reflecting the needs of the tool industry, which can be characterized by small quantities of various products. However, many problems remain in ensuring the reliability of ceramic tools for industrial use. In this study, alumina inserts, a representative ceramic tool, was manufactured using the digital light process (DLP), a 3D printing method. Alumina inserts prepared by 3D printing are pressurelessly sintered under the same conditions as coupon-type specimens prepared by press molding. After sintering, a hot isostatic pressing (HIP) treatment is performed to investigate the effects of relative density and microstructure changes on hardness and fracture toughness. Alumina inserts prepared by 3D printing show lower relative densities than coupon specimens prepared by powder molding but indicate similar hardness and higher fracture toughness values.

• 한국분말재료학회지
• /
• 제26권6호
• /
• pp.471-476
• /
• 2019

Additively manufactured metallic components contain high surface roughness values, which lead to unsatisfactory high cycle fatigue resistance. In this study, high cycle fatigue properties of selective laser melted Ti-6Al-4V alloy are investigated and the effect of dry-electropolishing, which does not cause weight loss, on the fatigue resistance is also examined. To reduce the internal defect in the as-built Ti-6Al-4V, first, hot isostatic pressing (HIP) is conducted. Then, to improve the mechanical properties, solution treatment and aging are also implemented. Selective laser melting (SLM)-built Ti64 shows a primary α and secondary α+β lamellar structure. The sizes of secondary α and β are approximately 2 ㎛ and 100 nm, respectively. On the other hand, surface roughness Ra values of before and after dry-electropolishing are 6.21 ㎛ and 3.15 ㎛, respectively. This means that dry-electropolishing is effective in decreasing the surface roughness of selective laser melted Ti-6Al-4V alloy. The comparison of high cycle fatigue properties between before and after dry-electropolished samples shows that reduced surface roughness improves the fatigue limit from 150 MPa to 170 MPa. Correlations between surface roughness and high cycle fatigue properties are also discussed based on these findings.

• 한국분말재료학회지
• /
• 제19권3호
• /
• pp.215-219
• /
• 2012

An attempt was made to evaluate creep reliability of two commercial Ni-based superalloys by using ultrasonic wave. The materials include fine-grained PM alloy fabricated by mechanical alloying and subsequent hot isostatic pressing, and IN738LC cast alloy with a grain size of a few cm. Microstructural parameters (fraction of creep cavity and size of ${\gamma}^{\prime}$ precipitates) and ultrasonic parameters (velocity, attenuation) were measured to try to find relationships between them. Ultrasonic velocity decreased with creep cavity formation in PM alloy. On the other hand, no distinct changing trend of ultrasonic velocity was observed for IN738LC alloy. Ultrasonic attenuation was found to have a linear correlation with the size of ${\gamma}^{\prime}$ precipitates and was suggested as a potential parameter for monitoring creep reliability of IN738LC alloy.