• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.2
• /
• pp.23-29
• /
• 2014

The advanced traffic management system of intelligent transport systems automates the related traffic tasks such as vehicle speed, traffic volume and traffic incidents through the improved infrastructures like high definition cameras, high-performance radar sensors. For the safety of road users, especially, the automated incident detection and secondary accident prevention system is required. Normally, CCTV based image object detection and radar based object detection is used in this system. In this paper, we proposed the algorithm for real time highway incident detection system using multi surveillance cameras to mosaic video and track accurately the moving object that taken from different angles by background modeling. We confirmed through experiments that the video detection can supplement the short-range shaded area and the long-range detection limit of radar. In addition, the video detection has better classification features in daytime detection excluding the bad weather condition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.13-19
• /
• 2012

The fatalities rate for passenger vehicles, vans, and commercial vehicles is 1.23, 1.90 and 2.46 deaths per 10,000 registered vehicles, respectively. This shows that vans and commercial vehicles are vulnerable compare to passenger vehicles. To evaluate the crashworthiness of van and Light Truck Vehicle(LTV), we carried out frontal offset crash test at 64km/h, 40% overlap as per IIHS(Insurance Institute for Highway Safety). The test result show that LTV is very poor to protect occupant at frontal crash cause there is no safety system such as airbag and pretensioner and front end length(distance from front bumper to steering wheel) is short. One of the van rated as the lowest rating even it is equipped with airbag, cause its safety cage was collapsed during the test. This result shows that the structural integrity is very important in terms of occupant protection.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2228-2234
• /
• 2000

Steering of the vehicles on a slippery highway is a difficult task for most passenger car drivers. The steering vehicles on slippery roads tend to slide outward with less lateral forces than on nor mal roads. When the drivers notice that their vehicles on a slippery highway start to depart from the cornering lane, most of them make a sudden steering and/or braking, which in turn may induce spin-out and instability on their vehicles. In this paper, an active steering control method is proposed such that the vehicles in slippery roads are steered as if they are driven on the normal roads. In the proposed method, the estimated lateral forces acting on the steering tires are compared with the reference values and the difference is compensated by the active steering method. A fuzzy logic controller is designed for this purpose and evaluated on a steering Hardware-In-the-Loop Simulation (HILS) system. Steering performance results on the slippery curved and sinus roads demonstrate the effectiveness of the proposed controller. This method can be realized with the steer-by-wire concept and is promising as an active safety technology.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.11a
• /
• pp.367-372
• /
• 2004

Highway have to be constructed under thorough investigation about function, economy, safety of the traffic and environment, because they are needing huge budget for construction and management as important facilities of the social overhead capital in the national economics. Initially the construction of roads becomes effective the plan, the design, construction phase. The design is foundation of accomplishment of the roads operation, the results of the design operation come to much effect a nation when using roads. Especially ancient design methods were not expected for visual effects as attaching weight to 2-dimensional drawing from flat. Therefore, it is difficult to recognize troubles happened during the work operation besides, many troubles are solved by modification of drawings as situations. For solving of those of the problems, it is emphasize on visual effect through introduction of 3-dimensional design from the initial phase. In case of national conditions, limited national land has caused increasing weight for construction of the roads through cities as the urban centered development. thereupon, citizens are increasing concern about the right of the light and the environmental effect, road designs and construction of the structures under agreement with local residents cause to make troubles. The analysis of 3-dimensional design is necessary as intermediation for decision making. In this study, Virtual reality techniques in 3-dimensional roads design are expected to visual effect on the publishing Internet Web, find problems in first phase and make decision between users and people having civil appeal.

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.127-133
• /
• 2013

PURPOSES : The impact performance of flexible barrier system such as structural response, vehicular motion and occupant safety vary depending on the impact point. Thus, to properly evaluate the performance of a flexible barrier system, impact should be made to a point which will lead to the worst possible results. This point is called the Critical Impact Point (CIP). This paper presents the way to determine the CIP for a SB2 class flexible barrier system which is consisted of Thrie-Beam rail and circular hollow tube post of 2m span. METHODS: Barrier VII simulations were made for impact points; Case 1 at a post, Case 2 at 1/3 span downstream from a post, Case 3 at middle of the span, Case 4 at 2/3 span downstream from a post. For the structural performance (deflections), impact simulation of 8000kg-65km/h-15degree was used, and for vehicle motion and occupant safety, simulation of 1300kg-80km/h-20degree impact was made and analysed. RESULTS: Case 1 gave the largest dynamic deflection of 75.72cm and also gave the largest snag value of 44.3cm. Occupant safety and exit angle of the vehicle after the impact were not sensitive to the impact point and were all below the allowable limit. CONCLUSIONS : For the SB2 class flexible barrier system's CIP can be regarded as a post which is sufficiently away from the end of Length of Need in order to avoid the end-effect of the barrier system. It can be more economic in the long run because the normal concrete pavement material is likely to cost more due to higher probability of maintenance and repair and higher social cost due to traffic accident, etc.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.1-9
• /
• 2008

The current test methods are insufficient to evaluate and ensure the safety and reliability of vehicle system for all possible dynamic situation including the worst case such as rollover, spin-out and so on. Although the known NHTSA J-turn and Fish-hook steering maneuvers are applied for the vehicle performance assessment, they aren't enough to estimate other possible worst case scenarios. Therefore, it is crucial for us to verify the various worst cases including the existing severe steering maneuvers. This paper includes the procedure to search for other useful worst case based upon the existing worst case scenarios mentioned above and its application in simulation basis. The only human steering angle is selected as a design parameter here and optimized to maximize the index function to be expressed in terms of either roll angle or yaw rate. The obtained scenarios were enough to generate the worst case to meet NHTSA worst case definition (ex.2-inch wheel lift). Additionally, as an application, the worst case steering maneuver is acquired for the vehicle to operate with a simple ESP system. It has been concluded that the new procedure in this paper is adequate to create other feasible worst case scenarios for a vehicle system both with an intelligent safety control system and without it.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.3
• /
• pp.233-241
• /
• 2014

This paper contributes to development of a new method for detecting rear-side vehicles and estimating the positions for blind spot region or providing the lane change information by using vision systems. Because the real image acquired during car driving has a lot of information including the target vehicle and background image as well as the noises such as lighting and shading, it is hard to extract only the target vehicle against the background image with satisfied robustness. In this paper, the target vehicle has been detected by repetitive image processing such as sobel and morphological operations and a Kalman filter has been also designed to cancel the background image and prevent the misreading of the target image. The proposed method can get faster image processing and more robustness rather than the previous researches. Various experiments were performed on the highway driving situations to evaluate the performance of the proposed algorithm.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.7
• /
• pp.151-160
• /
• 2009

The aim of this study is to propose economical driving speed index which those are geometric road status; assess the levels of which those cost-benefit of driving energy consumption and emission; are search road safety design and operational technology for driving simulator. For the objective, we analyzed the current status of driving energy consumption and driving scenarios by the road alignments, and reviewed driving and technical specifications by the geometric types of road according to the implementation, and extended completion. Throughout the result of this study, diverse related driving information provision service, efficiently navigation driving module is expected to be implemented in the national highway design system.

• Korean Journal of Construction Engineering and Management
• /
• v.7 no.3 s.31
• /
• pp.138-148
• /
• 2006

The construction supervisors of the public companies are usually responsible for process management, quality management, safety management, and many other various tasks that occur during construction project. Public companies such as Korea Highway Corporation have developed a framework and manual for management and supervision of construction projects. But, there has been the change of business environment such as increase of private investment project and the introduce of construction management system recently. It has been necessary for construction supervisor to streamline the current project management system in the owner's aspect in order to cope with the expected new challenges. Accordingly, this research has been investigated and analyzed the operation system between Korean supervisor and foreign supervisor in their public corporation. This research has suggested the advanced project management in their public corporation. Especially, this study has proposed the construction management manual for supervisors such as inspectors training, supervisors construction manual, and supervisors training road map.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.858-862
• /
• 2008

KICT has been carrying out inventory research on the cut slopes of national roads. Inventory research results are basic data used in cut slope management system. Inventory data are classified by general status, cut slope characteristics and inspector opinion. Cut slope inventory data are utilized to figure out dangerous slopes and decide survey ranking of detailed safety diagnostication. This paper drew the distribution of dangerous cut slopes using inventory data in Chungcheongdo, then verified an efficiency on distribution of dangerous cut slopes by comparing occurrence frequency of real collapsed cut slopes.