• Korean Journal of Materials Research
• /
• v.4 no.3
• /
• pp.287-294
• /
• 1994

PAN-based carbon fiber roving and fabric were heat treated at the temperature of $2170^{\circ}C$. Using non-heat treated and heat treated fabric, greenbodies of CFRP and GFRP were manufactured in the Autoclave. After the analysis of heat treated and non-heat treated carbon fiber roving and two types of greenbodies, the variations of physical and mechanical properties of carbon fibers and greenbodies with heat treatment were studied. Observing the cross-section of carbon fiber with SEM, we knew the diameter of carbon fiber was decreased from 6.8gm to 6.4p1. The results of TGA showed that the oxidation resistence was enhanced after heat treatment. The tensile strength of carbon fiber was decreased from (3.11$\pm 0.32)\times 10^3$ MPa to (1.87$\pm 0.26)\times 10^3$MPa, but tensile modulus was increased from (1.94$\pm 0.06)\times 10^5$ MPa to (2.02$\pm 0.11)\times 10^5$MPa after heat treatment. The interlaminar shear strengths of CFRP and GFRP were 148.8$\pm$1.6Mpa and 82.2$\pm$1.1Mpa, respectively. Torch test showed that CFRP was abraded smoothly but GFRP was delaminated.

• Korean Journal of Materials Research
• /
• v.10 no.2
• /
• pp.111-116
• /
• 2000

Fracture mode and carbide reactions of cast alloy 738LC during thermal exposure and creep at 816$^{\circ}C$/440MPa and 982$^{\circ}C$/152MPa were investigated. Crystallographic transgranular failure was observed in the specimen crept at 816$^{\circ}C$ due to shearing on the slip plane. Because selective oxidation at the grainboundaries which was exposed at the surface leads reduction in surface energy, however, early initiation of crack at the grainboundaries and intergranular failure were observed in the specimen crept at 982$^{\circ}C$/152MPa. As a result of decomposition of MC carbide at the tested temperatures, M(sub)23C(sub)6 carbide precipitated either on the grainboundaries or on the deformation band. The applied stress enhanced decomposition of MC. $\sigma$phase nucleated from Cr(sub)23C(sub)6 then grew to the ${\gamma}$+${\gamma}$\\` matrix. Precipitation of $\sigma$was accelerated by increasing temperature and applied stress.

• Clean Technology
• /
• v.26 no.2
• /
• pp.116-121
• /
• 2020

In this paper, the recycling of waste Ni-MH battery by-products for electric vehicle is studied. Although rare earths elements still exist in waste Ni-MH battery by-products, they are not valuable as materials in the form of by-products (such as an insoluble substance). This study investigates the recovering of rare earth oxide for solvent extraction A/O ratio, substitution reaction, and reaction temperature, and scrubbing of the rare earth elements for high purity separation. The by-product (in the form of rare earth elements insoluble powder) is converted into hydroxide form using 30% sodium hydroxide solution. The remaining impurities are purified using the difference in solubility of oxalic acid. Subsequently, Yttrium is isolated by means of D2EHPA (Di-[2-ethylhexyl] phosphoric acid). After cerium is separated using potassium permanganate, lanthanum and neodymium are separated using PC88A (2-ethylhexylphosphonic acid mono-2-ethylhexyl ester) and it is calcinated at a temperature of 800 ℃. As a result of the physical and chemical measurement of the calcined lanthanum and neodymium powder, it is confirmed that the powder is a microsized porous powder in an oxide form of 99.9% or more. Rare earth oxides are recovered from Ni-MH battery by-products through two solvent extraction processes and one oxidation process. This study has regenerated lanthanum and neodymium oxide as a useful material.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.32 no.3
• /
• pp.5-18
• /
• 2024

Chemical oxygen demand (COD), an organic material measurement index, has a limit to the management of the total amount of all organic materials including non-degradable organic materials due to low oxidation rate. So total organic carbon (TOC) that can measure organic materials more accurately is introduced and used as a measurement index. Several environmental companies including company A in Gyeonggi-do dilute raw wastewater first and then treats it with chemicals. And an activated carbon is used at the rear stage to treat total organic carbon even though various treatment processes can be applied to reduce TOC in wastewater. There are some problems such as use of a lot of diluting water and generation of an excessive amount of sludge, so it is urgent to come up with an alternative plan. Therefore, in this study, an application experiment was conducted on two different methods for improving the TOC reduction efficiency of waste water from Company A. The first method is the evaluation of the substitution potential of powered activated carbon(PAC), an adsorbent currently used, by manufacturing cellulose-based graphene like carbon (CGLC). This first study showed that CGLC had about 10% higher TOC adsorption efficiency than commercial PAC, showing the possibility of being applied as an alternative adsorbent for PAC in water treatment sites. The second method relates to the removal of TOC by sulfate radials produced by persulfate (PS) activation. Two activation methods were applied: using CGLC and PAC as carbon-based catalyst and using the high temperature of wastewater for PS activation. As a result of using PAC and CGLC as PS activation materials, the TOC removal rate was lower than the adsorption amount of TOC by CGLC and PAC due to excessive chlorine ions present in the real wastewater. However, as a result of using the high water temperature (55~60℃) of the field wastewater for PS activation, it showed a much greater TOC removal efficiency than PAC alone, CGLC alone, and using a carbon-based catalyst for PS activation. When PS was injected more than 0.5%, it showed a TOC removal efficiency of 95% or more within 24 hr. In addition, when PS was injected more than 0.3%, the TOC concentration could be lowered to less than 75 ppm, which is the wastewater discharge standard applied to company A. When these results were summarized, raw wastewater of high temperature can be treated with a simple process of only adding of PS and discharged by treating TOC below the wastewater discharge standard applied to company A.

• Economic and Environmental Geology
• /
• v.25 no.4
• /
• pp.397-416
• /
• 1992

In the present study, three clay deposits, named the Seongsan, Ogmaesan and Haenam deposits, were investigated. The altered zones are recognized in the hydrothermally altered rocks of the clay deposits from the center of the alteration to the margin: Kaolin, Kaolin-Quartz, Quartz, Sericite and Chlorite zones in the Seongsan deposits; Quartz zone, Alunite zone, Kaolin zone, Sericite zone and Chlorite zone in the Ogmaesan deposits; Quartz zone, Pyrophyllite zone, Sericite zone and Chlorite zone in the Haenam deposits. These zones can be grouped into two types of alteration: Acidic alteration such as Pyrophyllite zone, Alunite zone, Quartz zone, Kaolin zone, Kaolin-Quartz zone and a part of Sericite zone; Propylitic alteration such as Chlorite zone and a part of Sericite zone. All clay deposits belong to high-sulfidation (acid-sulfate) system. The rocks of the acidic alterations are composed of pyrophyllite, alunite, kaolin minerals, sericite, quartz and pyrite. On the basis of bulk chemical compositions, it was found that some components such as $SiO_2$, $TiO_2$, $Fe_2O_3$, FeO, MgO, CaO, $K_2O$ and $Na_2O$ were mobilized considerably from the original rocks. The mobility of these major elements is related to, and controls, mineral assemblages in each altered zone. Polytypes of sericite are determined as $2M_1$ and 1M by X-ray diffraction method. The amount of $2M_1$ is nearly equal to that of 1M in the Seongsan deposits whereas $2M_1$ is less and higher than that of 1M in the Ogmaesan and the Haenam deposits. These facts indicate that formation temperature of sericite is relatively high in the Haenam deposits, moderate in the Seongsan deposits, and low in the Ogmaesan deposits. The ratios of Na/(K+Na) for alunite in the Ogmaesan deposits determined by electron microprobe analyzer (EPMA) are higher than those in the Seongsan deposits. Thus, the alunite of the Ogmaesan deposits must have been formed from the solutions with relatively high aqueous Na/(K+Na) ratios and low pH at a high temperature rather than that of the Seongsan deposits. From all data, it is clarified that alunite is hypogene in origin, and has been formed by oxidation of hydrogen sulfide in the steam-heated environment, and that alunite has been produced by the spectacular solfataric alteration observed at the surface of some present-day hydrothermal systems.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.394-401
• /
• 2005

A nonthermal plasma-assisted fuel reformer was developed and the effects of operating variables on the performance of this reformer were studied. The $H_2$-rich reformed gas from the reformer was injected into a diesel engine under an idle condition and the effects of the amount of injected gas on the NO and soot reduction were investigated. It was found that with increasing electric power consumption, the degree of facility of ignition of the reforming reaction in the reformer could be enhanced. The performance of the reformer including $H_2$ concentration, $H_2$ recovery, and energy conversion was affected only by the O/C mole ratio. This was because the equilibrium reaction temperature was governed by the O/C mole ratio. With increasing O/C mole ratio, the $H_2$ recovery and energy conversion passed through the maximum values of 33.4% and 66%, respectively, at an O/C mole ratio between 1.2 and 1.5. The reason why the $H_2$ recovery and energy conversion increased with increasing O/C mole ratio when the O/C mole ratio was lower than $1.2{\sim}1.5$ appeared to be that the complete oxidation reaction occurred more enough with increasing O/C mole ratio in this low O/C mole ratio range and accordingly the reaction temperature increased. Whereas the reason why the $H_2$ recovery and energy conversion decreased with increasing O/C mole ratio when the O/C mole ratio was higher than $1.2{\sim}1.5$ appeared to be that the complete oxidation reaction was further advanced and the $H_2$ recovery and energy conversion decreased. As the weight ratio of reformed diesel to total diesel which entered the diesel engine was increased to $18.2{\sim}23.5%$, NO and soot reduction efficiencies increased and reached as values high as 68.5% and 23.5%, respectively.

• Clean Technology
• /
• v.22 no.3
• /
• pp.175-180
• /
• 2016

Tyrosinases catalyze the hydroxylation of a monophenol (monophenolase activity) and the conversion of an o-diphenol to o-quinone (diphenolase activity), which are mainly involved in the modification of tyrosine residues into 3,4-dihydroxyphenyl-alanine (DOPA) and DOPA/DOPAquinone-derived intermolecular cross-linking. Previously, we obtained a slightly acidic and cold-active tyrosinase, tyrosinase-CNK, by our recombinant protein approach. The enzyme showed optimal activity at pH 6.0 and 20 ℃ with an abnormally high monophenolase/diphenolase activity ratio and still had approximately 50% activity compared with the highest activity even in ice water. Here, we investigated reaction stability of the recombinant tyrosinase-CNK as a psychrophilic enzyme. The enzyme showed remarkable thermal stability at 0 ℃ and the activity was well conserved in repeated freeze-thaw cycles. Although water-miscible organic solvent as reaction media caused the activity decrease of tyrosinase-CNK as expected, the enzyme activity was not additionally decreased with increased concentration in organic solvents such as ethanol and acetonitrile. Also, the enzyme showed high salt tolerance in chaotropic salts. It was remarkably considered that 2⁺ metal ions might inhibit the incorporation of Cu²⁺ into the active site. We expect that these results could be used to design tyrosinase-mediated enzymatic reaction at low temperature for the production of catechols through minimizing unwanted self-oxidation and enzyme inactivation.

• Mineral and Industry
• /
• v.26
• /
• pp.1-12
• /
• 2013

In this study, an accelerated carbonation process was applied to stabilize hazardous heavy metals of industrial solid waste incineration (ISWI) bottom ash and fly ash, and to reduce $CO_2$ emissions. The most commonly used method to stabilize heavy metals is accelerated carbonation using a high water-to-solid ratio including oxidation and carbonation reactions as well as neutralization of the pH, dissolution, and precipitation and sorption. This process has been recognized as having a significant effect on the leaching of heavy metals in alkaline materials such as ISWI ash. The accelerated carbonation process with $CO_2$ absorption was investigated to confirm the leaching behavior of heavy metals contained in ISWI ash including fly and bottom ash. Only the temperature of the chamber at atmospheric pressure was varied and the $CO_2$ concentration was kept constant at 99% while the water-to-solid ratio (L/S) was set at 0.3 and $3.0dm^3/kg$. In the result, the concentration of leached heavy metals and pH value decreased with increasing carbonation reaction time whereas the bottom ash showed no effect. The mechanism of heavy metal-stabilization is supported by two findings during the carbonation reaction. First, the carbonation reaction is sufficient to decrease the pH and to form an insoluble heavy metal-material that contributes to a reduction of the leaching. Second, the adsorbent compound in the bottom ash controls the leaching of heavy metals; the calcite formed by the carbonation reaction has high affinity of heavy metals. In addition, approximately 5 kg/ton and 27 kg/ton $CO_2$ were sequestrated in ISWI bottom ash and fly ash after the carbonation reaction, respectively.

• Journal of Korean Medicine Rehabilitation
• /
• v.26 no.4
• /
• pp.1-8
• /
• 2016

Objectives Danggwisu-san (Dangguixu-san) is a herbal prescription frequently used to treat pain or swelling caused by contusion. To determine the expiration period through scientific methodology, stability of Danggwisu-san (Dangguixu-san) water extract, a herbal medicine, was examined under various storage conditions and periods. Methods Danggwisu-san (Dangguixu-san) was stored either at room temperature ($23{\pm}2^{\circ}C$), under a refrigerating condition ($4^{\circ}C$) or under a freezing condition ($-18{\pm}2^{\circ}C$) for 0, 1, 2, 3 or 4 weeks and then freeze-dried. Total phenol and total flavonoid amounts were investigated; contents of amygdalin (Prunus persica), paeoniflorin (Paeonia lactiflora), and glycyrrhizin (Glycyrrhiza uralensis) - the marker compounds of Danggwisu-san (Dangguixu-san) - were also analyzed through high performance liquid chromatography (HPLC). Results No significant change in total phenol and total flavonoid amounts was observed under the indicated storage conditions. Moreover, the contents of marker compounds, i.e. amygdalin, paeoniflorin, and glycyrrhizin, did not alter significantly under the indicated conditions, as well. Conclusions Danggwisu-san (Dangguixu-san) was found to be stable up until 4 weeks under the indicated conditions. Further studies on efficacy and long-term stability are warranted to establish the expiration period of Danggwisu-san (Dangguixu-san).

• Korean Journal of Food Science and Technology
• /
• v.9 no.3
• /
• pp.183-189
• /
• 1977

Studies were made of the continuous production of Pyridoxal 5'-phosphate (pyridoxal-p) on simultaneously immobilized cell column. Whole-cell of Pseudomonas polycolor having high activity of pyridoxine 5'-phosphate (pyridoxine-p) oxidase and Kloeckera sp. No. 2201 having high activity of catalase were used as the enzyme materials. The enzyme sources were entrapped in a polyacrylamide gel. Enzymatic properties of the simultaneously immobilized cells were investigated, comparing with those of the mixed whole-cells of the microorganisms. The simultaneously immobilized cells had higher enzyme activity than singly immobilized cells of Pseudomonas polycolor. From this result, the simultaneously immobilized pyridoxine-p oxidase-catalase system could be available to exert a protective effect upon the pyridoxine-p oxidase by destroying $H_2O_2$ which is a by-product of pyridoxine-p oxidation. The optimum pH was 9.0 for the immobilized cells and the whole-cells. The optimum temperature was $45^{\circ}C$ for the immobilized cells and $40^{\circ}C$ for the whole-cells. The pyridoxine-p oxidase of the immobilized cells were activated by $Hg^{++}$ and some SH-compounds.