• 열처리공학회지
• /
• 제24권4호
• /
• pp.203-208
• /
• 2011

Recently, from general machine parts and automobile parts using carbon steel to a mold, there has been efforts for improving durability and attrition resistance of these parts. Especially, heat treatment with laser which works fast and automatically can be used for the mass production with high quality. Moreover, local heat treatment can be used to handle with complex and precise parts. Accordingly, we analyzed hardening characteristics of carbon steel using the finite element method and compare the experimental results to have more reliability. We also proved the cause of thermal deformation with temperature and stress distribution by heat treatment. After these analysis and experimental, we found that each maximum hardness of the two tests was 728 Hv and 700 Hv, on condition of $1050^{\circ}C$ heating temperature, and 2 mm/sec laser speed. We also found that difference of surface stress-distribution was occurred, and this makes deformation mode up after heat treatment.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2017년도 춘계학술대회
• /
• pp.65-68
• /
• 2017

본 논문은 정지궤도위성 관측탑재체 고속 데이터 전송을 위한 X-대역 이중모드 고전력 채널필터의 우주인증모델에 대한 멀티팩터 시험을 통하여 설계시 요구되는 8 dB 마진과의 비교 검토를 수행하였다. 해석적인 요구되는 마진을 시험을 통해서도 충족하며, 만족한 시험결과를 얻었음을 확인하였다. 멀티팩터의 설계 및 시험은 ECSS의 규격을 준용하여 시험이 실시되었으며, 이를 근간으로 설계시 마진을 충분히 확보되면, 별도의 시험 없이 우주인증 모델용 필터 개발에 있어서 참조하여 사용할 수 있을 것으로 제안한다.

• 한국통신학회논문지
• /
• 제25권9B호
• /
• pp.1518-1526
• /
• 2000

본 논문은 기존 표준 단일모드 광섬유 링크를 통하여 초고속 광신호의 장거리 전송이 가능하도록 분산보상 광섬유를 이용한 최적 분산보상 기법에 기반을 둔 전송링크 설계 방법을 제안하였다. 제안한 방법에서는 광섬유의 비선형성에서 비롯되는 자기위상변조(Self-Phase Modulation: SPM)와 광증폭기에서 발생하는 증폭자연방출(Amplified Spontaneous Emission : ASE) 잡음에 대하여 증폭기간 거리와 중계기간 거리를 최적화함으로써 전송신호 속도에 따른 최대 전송거리를 제시하였다. 또한 주어진 증폭기간 거리와 중계기간 거리에 대하여 ASE 잡음과 SPM의 효과의 균형적 관계로부터 최적의 입력 신호전력의 범위가 있음을 제시하였다.

• Journal of Electrical Engineering and Technology
• /
• 제13권5호
• /
• pp.1935-1944
• /
• 2018

With the increase of the production of energy from renewable, it becomes important to look at techniques to store this energy. Therefore, a single winding bearingless flywheel motor (SWBFM) specially for flywheel energy storage system is introduced. For the control system of SWBFM, coupling between the torque and the suspension subsystems exists inevitably. It is necessary to build a reasonable radial force mathematical model to precisely control SWBFM. However, SWBFM has twelve independently controlled windings which leads to high-order matrix transformation and complex differential calculation in the process of mathematical modeling based on virtual displacement method. In this frame, a Maxwell tensor modeling method which is no need the detailed derivation and complex theoretical computation is present. Moreover, it possesses advantages of universality, accuracy, and directness. The fringing magnetic path is improved from straight and circular lines to elliptical line and the rationality of elliptical line is verified by virtual displacement theory according to electromagnetic torque characteristics. A correction function is taken to increase the model accuracy based on finite element analysis. Simulation and experimental results show that the control system of SWBFM with radial force mathematical model based on Maxwell tensor method is feasible and has high precision.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 G
• /
• pp.3215-3217
• /
• 1999

In this paper, a new structure of realizing switching control logic for Data Weighted Average Technique is suggested. It uses memory and adder for summing past binary input and this summed data is used to select one switch in control logic. This control logic acts in parallel regardless of resolution so increasing resolution don't affect on converting speed. In this reason, high speed and high resolution D/A converter based on Data Weighted Average Technique could be made. In this paper, 4 bits current mode thermometer code D/A converter is degined and simulated by using HSPICE. Simulated results show that new structure of D/A converter has more than 250MHz converting speed and less than 0.0003[LSB] INL error. It is very useful in low power circuit because of using 3.3 V supply voltage.

• International Journal of Automotive Technology
• /
• 제8권5호
• /
• pp.543-553
• /
• 2007

It is becoming increasingly difficult for engines using conventional fuels and combustion techniques to meet stringent emission norms. The homogeneous charge compression ignition(HCCI) concept is being evaluated on account of its potential to control both smoke and NOx emissions. However, HCCI engines face problems of combustion control. In this work, a single cylinder water-cooled diesel engine was operated in the HCCI mode. Diesel was injected during the suction stroke($0^{\circ}$ to $20^{\circ}$ degrees aTDC) using a special injection system in order to prepare a nearly homogeneous charge. The engine was able to develop a BMEP(brake mean effective pressure) in the range of 2.15 to 4.32 bar. Extremely low levels of NOx emissions were observed. Though the engine operation was steady, poor brake thermal efficiency(30% lower) and high HC, CO and smoke were problems. The heat release showed two distinct portions: cool flame followed by the main heat release. The low heat release rates were found to result in poor brake thermal efficiency at light loads. At high brake power outputs, improper combustion phasing was the problem. Fuel deposited on the walls was responsible for increased HC and smoke emissions. On the whole, proper combustion phasing and a need for a well- matched injection system were identified as the important needs.

• 소음진동
• /
• 제9권2호
• /
• pp.317-323
• /
• 1999

Dynamic characteristics of catenary that supplies electrical power to high-speed trains are investigated. A simple catenary is composed of the contact and messenger wires connected by droppers possessing bi-directional stiffness properties. For slender, repeating structures such as catenary, both the wave propagation and vibration properties need to be understood. The influence of parameters that determine catenary dynamics are investiaged through numerical simulations involving finite element models. The effects of the tension and flexural rigidity of the contact wire is first investigated. The effects of dropper characteristics are then investigated. For linear droppers wave propagation as well as modal properties are determined. For large catenary motion, droppers can be modeled as bi-directional elements possessing low stiffness in compression and high stiffness in tension. For this case, impulse response is computed and compared with the cases of linear droppers. It is found that the catenary dynamics are primarily determined by contact wire tension and dropper properties, with large responses observed in 5∼40 Hz frequency range. In particular, the dropper stiffness and spacing are found to have dominant influence on the response frequency and the wave transmission characteristics.

• Journal of Magnetics
• /
• 제16권1호
• /
• pp.71-73
• /
• 2011

Hybrid electric vehicles have attracted much attention of late, emphasizing the necessity of developing traction motors with a high input current and a wide speed range. Among such traction motors, various researches have been conducted on interior permanent-magnet synchronous motors (IPMSMs) with high power density and mechanical solidity. Due to the complexity of its parameters, however, with nonlinear motor characteristics and current vector control, it is actually difficult to accurately estimate the base speed within an actual operating speed range or a voltage limit. Moreover, it is impossible to construct an efficiency map as the efficiency differs according to the control mode. In this study, a simulation method for operation performance considering the nonlinearity of IPMSM was proposed. For this, datasets of various nonlinear parameters were made via the finite-element method and interpolation. Maximum torque-per-ampere and flux-weakening control were accurately simulated using the datasets, and an IPMSM efficiency map was accurately constructed based on the simulation. Lastly, the validity of the simulation was verified through tests.

• 한국진공학회지
• /
• 제7권s1호
• /
• pp.106-117
• /
• 1998

Fluorocarbonated-SiO2 films were deposited on p-type Si(100) substrate using FSi$(OC_2H_5)_3$ (FTES), and $O_2$ mixture gases by a helicon plasms source. High density $O_2$/FTES/Ar plasma of ~$10^{12} \textrm{cm}^{-3}$ is obtained at low pressure (<3mTorr) with RF power above 900 W in the helicon plasma source. Optical emission spectroscopy (OES) is used to study the relation between the relative densities of the radicals and the film properties. The FTES and $O_2$ gases are greatly dissociated at the helicon mode that is launched at the above threshold plasma density. FTIR and XPS spectra shows that the film has Si-F, and C-F bonds during the formation process of the film which may lower the dielectric constant greatly. The relative dielectric constant, leakage current density, and dielectric breakdown voltage are about 2.8, $8\times10^{-9}\textrm{A/cm}^2$, and > 12 MV/cm, respectively.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.70-75
• /
• 2002

The penetration potential of TIG welding in one single run is limited, though the process itself generates high quality welds with good weld cosmetics. This is one of the main reasons, which has contributed to its development in high duty applications such as those encountered in aeronautical, aerospace, nuclear & power plant applications. For these applications, stainless steels, titanium k nickel based alloys are most often used. As these materials remain very sensible to weld heat input k atmospheric pollution, stringent processing conditions are imposed. For example welding of titanium alloys requires argon shielding of weld zone and for 5 mm thick plates multi-pass runs & filler additions are required. This multi-run operation not only raises the welding cost, but also increases defect risks. In recent years, extensive interest has been raised by the possibility to increase weld penetrations through flux applications & the process is designated ATIG-activated TIG, or FBTIG-flux bounded TIG. The improved welding performance of such flux assisted TIG is related to arc constriction and surface tension effects on weld pool. The research work by authors has lead to the formulation of welding fluxes for stainless steels k titanium alloys with TIG Process. These fluxes are now commercialized & some applications in industry have already been carried out. FBTIG for aluminum has been proposed with silica application for AC mode TIG welding. The paper highlights the fundamentals of flux role in TIG welding and illustrates some industrial applications.