• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1237-1240
• /
• 2007

Tire noise is a major noise source at high speeds. One of the noise source is controlled by pattern and structure. Pattern noise is effected by the shape of tread. And the bending stiffness of tire is influenced to the resonance of tire‘s belt. But in high frequency region, FEA is not appropriated with application. So this paper discusses about wave propagation of tire. There has been much effort to verify the flexural wave velocity with structure design specification.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.138-138
• /
• 2010

X-ray systems for medical treatment use noninvasive procedures. I fabricated a high tension generator of a full-wave rectification type using a LC resonant inviter. It is said that a full-wave rectifying X-ray equipment such as the fabricated system can shorten initiating period and be precision control because of stable output, compared with the X-ray equipment of a half wave rectifying type used in the usual clinical medicine. In order to evaluate the capability of the fabricated high tension generator, I performed exposure dose characteristics experiments.

• Proceedings of the KSR Conference
• /
• 1998.05a
• /
• pp.596-603
• /
• 1998

The entry compression wave, which is generated at the entrance of the tunnel, is almost always associated with the pressure transients in the tunnel as well as the impulse noise at the exit of the tunnel. It is highly required to design the train nose shape that can minimize such undesirable phenomena. The objective of the current work is to investigate the effects of the train nose shape on the entry compression wave. Numerical computations were applied to one-dimensional unsteady compressible flow in high-speed railway train/tunnel systems. A various shape of train noses were tested for a wide range of train speeds. The results showed that the strength of the entry compression wave is not influenced by the train nose shape, but the time variation of pressure in the entry compression wavefront is strongly related to the train nose shape. The current method of the characteristics was able to represent a desirable nose shape for various train speeds. Optimum nose shape was found to considerably reduce the maximum pressure gradient of the entry compression wave.

• ETRI Journal
• /
• v.33 no.3
• /
• pp.462-465
• /
• 2011

A millimeter-wave (mm-wave) high-linear low-noise amplifier (LNA) is presented using a 0.18 ${\mu}m$ standard CMOS process. To improve the linearity of mm-wave LNAs, we adopted the multiple-gate transistor (MGTR) topology used in the low frequency range. By using an MGTR having a different gate-source bias at the last stage of LNAs, third-order input intercept point (IIP3) and 1-dB gain compression point ($P_{1dB}$) increase by 4.85 dBm and 4 dBm, respectively, without noise figure (NF) degradation. At 33 GHz, the proposed LNAs represent 9.5 dB gain, 7.13 dB NF, and 6.25 dBm IIP3.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.467-468
• /
• 2006

To perform the comparative study, we experimented on two differential epitaxial structures, the conventional Metamorphic High Electron Mobility Transistor (MHEMT) using the InAlAs/InGaAs structure and the InP-composite channel MHEMT adopting the InAlAs/InGaAs/InP/n-InP structure. Compared to the conventional MHEMT, the InP-composite channel MHEMT shows improved breakdown performance; over about 3.5 V. This increased breakdown voltage can be explained by the lower impact ionization coefficient of the InP-composite channel MHEMT than that of the conventional MHEMT.

• Journal of Industrial Technology
• /
• v.27 no.A
• /
• pp.177-184
• /
• 2007

This paper presents a miniaturized electromagnetic wave detector. The dimension is reduced down to $31{\times}18{\times}13.5mm^3$ by using common OP-AMPs for amplification and oscillation. The strength from wave radiators is indicated by a color LED; green, orange and red colors mean the low, the middle and the high level, respectively. An alarm bell rings as the wave strength becomes above high level. The detector uses 3V battery. The detector could be used for a cellular phone decoration, a necklace pendant and a key holder.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1023-1028
• /
• 2004

A micro-pressure wave is generated by the high-speed train which enters a tunnel, and it causes explosive noise and vibration at the exit. It is known that train speed, train-tunnel area ratio, nose slenderness and nose shape mainly influence on generating micro-pressure wave. So it is required to minimize it by searching optimal values of such train shape factors and tunnel condition. In this study, response surface model, one of approximation models, is used to perform optimization effectively and analyze sensitivity of design variables. Owen's randomized orthogonal array and D-optimal Design are used to construct response surface model. In order to increase accuracy of model, stepwise regression is selected. Finally SQP(Sequential Quadratic Programming) optimization algorithm is used to minimize the maximum micro-pressure wave by using built approximation model.

• Journal of the Korean Society of Safety
• /
• v.23 no.5
• /
• pp.91-96
• /
• 2008

A reflected breakwater can be affected by wave pressure and power because it is to be concentrated by wave energy. The present study is to estimate hydraulic behavior affecting around a reflected breakwater, which is discontinuity cases and various angle of coner at the breakwater. The numerical model to investigate wave diffraction, which is important hydraulic factor in the ocean, is performed by using direct boundary element method. The present numerical results are compared with the solutions of approximate and absolute based on an eigenfunction, and the solution of analytical by Fresnel integral. The results of the present numerical simulation agreed well with those of the published numerical and analytical data. As a result of this study, wave height is high at the comer of breakwater, and it is to be high if angle of conner at the reflected breakwater is small.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.435-447
• /
• 2019

Energy Flow Finite Element Analysis (EFFEA) is a promising tool for predicting dynamic energetics of complicated structures at high frequencies. In this paper, the Energy Flow Finite Element (EFFE) formulation of complicated Mindlin plates was newly developed to improve the accuracy of prediction of the dynamic characteristics in the high frequency. Wave transmission analysis was performed for all waves in complicated Mindlin plates. Advanced Energy Flow Analysis System (AEFAS), an exclusive EFFEA software, was implemented using $MATLAB^{(R)}$. To verify the general power transfer relationship derived, wave transmission analysis of coupled semi-infinite Mindlin plates was performed. For numerical verification of EFFE formulation derived and EFFEA software developed, numerical analyses were performed for various cases where coupled Mindlin plates were excited by a harmonic point force. Energy flow finite element solutions for coupled Mindlin plates were compared with the energy flow solutions in the various conditions.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.1
• /
• pp.68-75
• /
• 2019

A low-crested structure (LCS) is an excellent feature not only because it provides shore protection but also because it is fully submerged. However, in order to properly control waves, it is necessary to maintain a certain range of crest height and width in consideration of the wave dimensions at the installation area. According to previous studies, an LCS has some wave breaking effect when the crest width is more than a fourth of the incident wavelength and the crest depth is less than a third of the incident wave height. In other words, if the crest width of the LCS is small or the crest depth is large, it cannot control the wave. Therefore, when an LCS is installed in a large sea area with a great tidal range in consideration of the landscape, waves cannot be blocked at high tide. In this study, the hydraulic performances of a typical trapezoidal LCS with a constant crest height and a low-crested structure with an adjustable crest height, which was called a tide-adapting low-crested structure (TA-LCS) in this study, were compared and evaluated under various wave conditions through hydraulic experiments. It was found that the wave transmission coefficients of the TA-LCS at high tide were lower than the values for the typical LCS based on empirical formulas. In addition, the hydraulic performances of the TA-LCS for wave reflection control were 12.9?30.4% lower than that of the typical LCS. Therefore, the TA-LCS is expected to be highly effective in controlling the energy of incoming waves during high tide even in a macro-tidal area.