• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1536-1537
• /
• 2011

The high-voltage circuit breaker plays an important role in the electrical system because there has been a need for suitable switching devices capable of initiating and interrupting the flow of the electric fault current. It continues as the contacts recede from each other and as the newly created gap is bridged by a plasma. The arc plasma happens inside the insulation nozzle of SF6 self-blast interrupter which is newly developed as the next-generation switching principle. The ablation of PTFE nozzle is caused by this high temperature medium, the PTFE vapor from the nozzle surfaces flows toward the outlets and the pressure chamber. The vapor makes the pressure of the chamber increased by heat and mass transfer from the arcing zone. Because the rate of ablation depends on the magnitude of applied current, it decreases when the current goes to zero. The compressed gas inside the chamber flows reversely toward the arc plasma during this moment. According to this principle, the arc can be cooled down and the fault current can be interrupted successfully. In this study, we calculate arc plasmas and thermal-flow characteristics caused by fault current interruption inside a SF6 self-blast interrupter, and to investigate the effect of PTFE ablation on the whole arcing history.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.2
• /
• pp.57-62
• /
• 2007

The lubricational characteristics about friction wear has an effect on the material quality of surface. In this paper, we studied the lubricational characteristics through the surface modification experiment by spray coating the surface with $MoS_{2}$ and PTFE solid lubricants. In the case of $MoS_{2}$ and PTFE coating, the friction coefficient of Journal is lower than that for noncoating so the friction characteristics is excellent. In particular, the beginning characteristics of $MoS_{2}$ coating is excellent, and in the case of PTFE coating, seizure dose not appear seizure. $MoS_{2}$ and PTFE coating are excellent in the extreme pressure at high load. The wear characteristics is excellent in the following order; PTFE < $MoS_{2}$ < Non Coating. For Non coating, seizure appears at the beginning due to the heat, but in the case of $MoS_{2}$ and PTFE coating, it will have the excellent heat stability even at high temperature.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.153-157
• /
• 2009

A Highly efficient Mercury-free Flat Fluorescent Lamp (MFFL) with dielectric barrier Xe gas discharge was developed for an alternative of conventional line-type Cold Cathode Fluorescent Lamps (CCFLs) which shows a wide voltage margin and a stable discharge operation for diffuse glow discharge with an application of a auxiliary electrode. Electro-optic characteristics of the MFFL were examined through the changes in ambient temperature, total pressure and Xe partial pressure. the single cell is expanded into a multi-structured configuration to realize a large sized lamp by a simple repetition of the single cells, and a new driving scheme is proposed for an adaptive brightness control using dual auxiliary electrodes and bi-polar drive scheme. In addition, interesting application of this ultra high luminance flat lamp by the optimization of the gas condition and the pattern of the rear phosphor layer is suggested as a good alternative of daylight lamp source

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.949-951
• /
• 1992

A low pressure DC plasma jet has been used to obtain diamond films from a mixture of $CH_4$ and $H_2$ with high deposition rate (>1$\mu\textrm{m}$/min). The effects of the deposition conditions such as torch geometry, substrate temperature, gas mixing ratio, chamber pressure, axial magnetic field on the diamond film properties such as morphology, purity, uniformity of the film and deposition rate, etc. have been examined with the aid of Scanning Electron Microscopy, X-Ray Diffraction, and Raman Spectroscopy. Both the growth rate and particle size increased rapidly for low methane concentrations but saturated and the morphology changed from octahedral to cubic structure when the concentration exceeded 1.0 %. Higher growth rates (>1.5${\mu}m$/min) can be obtained by applying an axial magnetic field to the DC plasma jet. Diamond obtained from the magnetized plasma jet also shows a sharp peak at 1332.5$cm^{-1}$ in the Raman Spectra and this result implies that higher growth rate with a good quality diamond films can he obtained by applying an external magnetic field to the plasma jet.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.11
• /
• pp.1630-1636
• /
• 2003

Automobile companies and research institutions in leading automobile-manufacturing nations have recently been very active with research regarding the HCCI engine for use in future vehicles. Because HCCI engines take advantage of high compression ratio and heat release rate, they exhibit high efficiency found in compression ignition engines. HCCI engines also utilize a lean air/fuel ratio resulting in low emissions of NO$_{x}$ and PM (particulate matter). The objective of this research is to determine the effects of EGR rate on the combustion processes of HCCI. for this purpose, a 4-cylinder, compression ignition engine was converted into a HCCI engine, and a heating device was installed to raise the temperature of the intake air and also to make it more consistent. In addition, a pressure sensor was inserted into each of the cylinders to investigate the differences in characteristics among the cylinders. The experimental study of the effects of EGR rate on various gas emissions, engine performance, etc. should prove to be a valuable source of information for the development of the HCCI engine.e.

• KSBB Journal
• /
• v.29 no.3
• /
• pp.193-198
• /
• 2014

Pretreatment of wastepaper using aqueous glycerol under high pressure was studied to enhance the enzymatic hydrolysis. The pretreatment was conducted over a wide range of conditions including temperatures of $150{\sim}170^{\circ}C$, sulfuric acid concentrations of 0.5~1.5%, and reaction times of 30~90 minutes. After the effect of glycerol concentration on the pretreatment performance was investigated, 70% glycerol was selected. As glycerol concentration was increased, higher digestibility was achieved due to higher lignin removal. The optimum condition was found to be around $160^{\circ}C$, 1%, and 60 minutes. At this condition, 60% and 35% of hemicellulose and lignin, respectively, were removed, while only 5% of cellulose was lost. The enzymatic digestibility was 76%, meaning that 73% of the glucan present in the initial substrate was recovered as glucose after enzymatic hydrolysis. Also, it was found that the temperature and acid concentration than the reaction time were more strongly related to the compositional removals and enzymatic digestibility.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.12
• /
• pp.968-976
• /
• 2009

As the global warming becomes a serious environmental problem, studies of reducing $CO_2$ emission in power generation area are in progress all over the world. One of the carbon capture and storage(CCS) technologies is known as oxy-fuel combustion power generation system. In the oxy-fuel combustion system, the exhaust gas is mainly composed of $CO_2$ and $H_2O$. Thus, high-purity $CO_2$ can be obtained after a proper $H_2O$ removal process. In this paper, an oxy-fuel combustion cycle that recovers the waste heat of a high-temperature fuel cell is analyzed thermodynamically. Variations of characteristics of $CO_2$ and $H_2O$ mixture which is extracted from the condenser and power consumption required to obtain highly-pure $CO_2$ gas were examined according to the variation of the condensing pressure. The influence of the number of compression stages on the power consumption of the $CO_2$ capture process was analyzed, and the overall system performance was also investigated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1323-1330
• /
• 2000

Recently, injection molding process became more popular than ever to produce large quantities of high precision products or optical products. Especially, optical disk that was made by injection mol ding process has been used for many years as a music play media or computer sub-device. The density of data in disk media has been increased continuously. But those optical disks can cause sensorial problems because of high birefringence or deformation from the residual stresses in the media. Therefore, it is necessary to study the effects of various process conditions on the final bireffingence structure in injection-molded disks for producing precision injection-molded products. In the present paper we have focussed on the effect of holding and compression pressures on the optical anisotropy remaining in the MOD by examining the gapwise distribution of birefringence and extinction angle. The effect of holding pressure was found to form the inner two bireffingence peaks. But the effect of compression pressure on the bireffingence distribution was found to make the uniform distribution near the center in the gapwise direction. Finally, the value of the birefringence near the wall decreased as the mold temperature increased.

• Journal of Hydrogen and New Energy
• /
• v.27 no.4
• /
• pp.341-348
• /
• 2016

The experiments related on structure and water electrolysis performance of HALE UAV stack were conducted in this study. Anode catalyst $IrRuO_2$ was prepared by Adam's fusion methods as 2~3 nm nano sized particles, and the cathode catalyst was used as commercial product of Premetek. The MEA (membrane electrode assembly) was manufactured by decal methods, anode and anode catalytic layers were prepared by electro-spray. HALE stack was composed of 5 multi-cells as $0.2Nm^3/hr$ hydrogen production rate with hydrogen pressure as 10 bar. The water electrolysis performance was investigated at atmospheric pressure and temperature of $55^{\circ}C$. Best performance of HALE UAV stack was recorded as cell voltage efficiency as 86%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.9
• /
• pp.979-982
• /
• 2004

The ZnO thin films were prepared by the FTS (facing target sputtering) system, which enables to provide high density plasma and a high deposition rate at a low working gas pressure. We introduced the AZO thin film in order to improve the crystallographic properties of ZnO thin film because of the AZO(ZnO:Al) thin film has an equal crystal structure to the ZnO thin film. ZnO/AZO thin films were deposited at a different oxygen gas flow ratio, R.T. 2mTorr working pressure and a 0.8A sputtering current. The film thickness and c-axis preferred orientation of ZnO/AZO/glass thin films were measured by ${\alpha}$-step and an x-ray diffraction (XRD) instrument. In the results, we could prepare the ZnO thin film with c-axis preferred orientation of about 6$^{\circ}$ on substrate temperature R.T. at O$_2$ gas flo rate 0.5.