• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.543-550
• /
• 2007

As an emerging materials in construction fields, FRP(fiber reinforced polymer) has been used in many area of civil engineering for its light weight and high strength. In this study we chose the 2nd Jindo-Bridge as a prototype, and evaluate effect of replacing steel components to FRP components through simplified 3D linear analysis. Static and modal analysis are done and the analysis results are compared with steel case analysis. From the static analysis results, the maximum stress of each component and maximum displacement of middle span are compared. Due to the reduction of deadload, the FRP structure causes less deflection than the original steel structure and from the reduced section (cable) analysis we confirmed the previous result. The occurrence wind velocity of flutter is compared by the frequency ratio.

• Composites Research
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2001

In this study, damage evaluation of glass fiber reinforced thermoplastic composites was investigated with acoustic emission method. Specimens of 1.7mm thickness laminate were made from PET and 7 layers o171ass fabrics. Notch and impact loading were added to the specimen and normal tensile test and tensile test with the dead load were carried out. AE signal was measured as the functions of notch ratio to the width0 and impact energy in order to find out the correlation between fracture mode and AE parameters. The result has shown that low amplitude of AE signal was due to the microcrack of matrix and its growth, whereas the amplitude in the mid range was the response to the delamination and interfacial separation. In the range of high amplitude above 90dB. the fracture of glass fabric was found. Tensile strength decreased with increasing notch ratio to the width and impact energy because of tile effect or delamination, the cracking of matrix and stress concentration. In proportion to the size of damaged area. AE signal showed its wider range of frequency and energy as well as increased number of hits.

• Transactions of Materials Processing
• /
• v.14 no.5 s.77
• /
• pp.432-438
• /
• 2005

Among the most of manufacturing process, plastic deformation method offers a significant advantage in productivity and enable mass production with controlled quality and low cost. From the point of view, micro forming is a well suited technology in manufacturing very small metallic parts, in particular for mass production, as they are required in many industrial products. Meanwhile, Al 5083 superplastic alloy with very small grains has a great advantage in achieving micro deformation under low stress due to its relatively low strength at a specific high temperature range. This paper describes the micro formability of Al 5083 superplastic alloy and its application to die forging of micro patterns. Micro formability tests of Al 5083 superplastic alloy were carried out with the specially designed micro forging system by using V-grooved micro dies and pyramidal dies made of (100) silicon. With these dies, micro forging was conducted by varying the applied load, material temperature and forging time The micro formability of Al 5083 superplastic alloy was evaluated by comparing $R_f$ value, where $R_f\;=\;A_f/A_v$ ($A_v$ : cross-sectional area of the flowed metal, $A_v$ : cross sectional area of V-groove). The micro formability of 3 dimensional Patterns was also evaluated using Pyramidal type micro dies.

• Journal of the Korean Ceramic Society
• /
• v.41 no.9
• /
• pp.663-669
• /
• 2004

Mullite and cordierite, which were stable oxides having excellent thermal and chemical characteristics, were widely used as an engineering and electronic materials. However, thermal shock resistance of the mullite was detriorated, and strength of the cordierite was also reduced at high temperatures. The mullite-cordierite composite powders were synthesized for solving these problems in this study. The mullite-cordierite composite powders were manufactured by the solution-polymerization method using mixtures of fused silica, aluminium nitrate, magnesium nitrate, and PVA. Crystallinity, phase formation, density, and surface area of the synthesis powders were characteristics. Fine mullite-cordlerite composite powders were successfully synthesized at 1300$^{\circ}C$ and their surface areas were about 20㎡/g after planetary milling for 1h. With increasing the milling time, surface area increased to 23 ㎡/g for 4h ana 24㎡/g for 8h.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.4
• /
• pp.21-29
• /
• 2005

Lightweight Foamed Soil (LWFS) could be the substitute of normal soils used in backfill to earth structures and embankment materials far soft ground improvement in port and harbor project because of its effectiveness in settlement reduction and earth pressure decrease due to its lightness. A series of triaxial and unconfined compression tests were performed to investigate behaviors of LWFS composed of dredged soils, cement and air foam, and cured at underwater conditions. The density of LWFS will increase if LWFS is cured at underwater conditions because high water pressure makes air foam disappear or demolish during the curing compared with LWFS cured at normal air conditions. This paper is to find the mechanical behaviors of LWFS cured at seawater depth of 5.0 m and 10.0 m, respectively, which simulates underwater curing conditions by underwater pressure simulator chamber developed during this study. In addition, new normalized factor formula, which takes account of mixing design conditions determining compressive strength of LWFS, was proposed to consider mixing design factor fur LWFS.

• Journal of Periodontal and Implant Science
• /
• v.38 no.4
• /
• pp.595-602
• /
• 2008

Purpose: Ti-6Al-4V alloy is widely used as an implant material because of its good biocompatibility and good mechanical property compared with commercial pure titanium. Otherwise, toxicity of aluminum and vanadium in vivo has been reported. Ti-8Ta-3Nb alloy is recently developed in the R&D Center for Ti and Special Alloys and it was reported that this alloy has high mechanical strength, no cytotoxicity and similar biocompatibility to commercial pure titanium, but many studies are needed for its clinical use. In these experiment, we carried out different surface treatment on each Ti-8Ta-3Nb alloy disks, then cultured cell on it and assessed biological response. Materials and Methods: cpTi, Ti-6Al-4V, Ti-8Ta-3Nb alloy disks were prepared and carried out sandblasting and acid etching (SLA) or alkali-heat treatment (AH) on the Ti-8Ta-3Nb alloy disks. We cultured primary rat calvarial cells on each surface and assessed early cell attachment and proliferation by scanning electron microscopy, cell proliferation, alkaline phosphatase activity. Result: The rates of cell proliferation on the cpTi, Ti-8Ta-3Nb AH disks were higher than others (p<0.05) and alkaline phosphatase activity was significantly enhanced on the Ti-STa-8Nb AH disks(p<0.05). Conclusion: Most favorable cell response was shown on the Ti-8Ta-3Nb AH surfaces. It is supposed that alkali-heat treatment of the Ti-8Ta-3Nb alloy could be induced earlier bone healing and osseointegration than smooth surface.

• Textile Coloration and Finishing
• /
• v.29 no.1
• /
• pp.45-54
• /
• 2017

Ultraviolet radiation have much influenced with a deep wrinkles, roughness, laxity of skin damage and pigmentation through oxidative stress and oxidative photo-damage. This study investigates the functional properties of hydrogel facial mask sheets made from agar, Styela clava tunics and Broussonetia papyrifera tunics. The skin of S. clava is covered with a hard cellulose containing glycoprotein, glycosaminoglycan and chondroitin sulfate. B. papyrifera is better known as Paper mulberry. It contains kazinol which serves as a tyrosinase inhibitor and skin whitening agent. The tensile strength of facial mask sheet was measured by universal testing machine, and the water absorption and moisture permeability of facial mask sheet were measured by dryer. Additionally, the DPPH assay and MTT assay were conducted for anti-oxidative activity and cytotoxicity of facial mask sheet. The whitening effect of the facial mask sheet was measured by tyrosinase inhibitor assay. These tests showed that the three ingredients are suitable cosmetic materials. The results reveal that they produce a high quality hydrogel facial mask sheet when the membrane contains 1%(W/V) of agar, 0.1%(W/V) of B. papyrifera tunics and 0.05%(W/V) of S. clava tunics.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.823-831
• /
• 1996

At the ratio [$H_2O$]/[TEOS]=1.7, the silica sol was synthesized by partial hydrolysis in the presence of acid catalyst. After stabilizing the silica sol by trimethylsilylation, the molecular weight and viscosity of the sol obtained at various reaction times were examined to determine a best spinnability of the sol. Gel fibers were prepared from the sol solution after removing solvent in the solution, and the gel fibers were heated at $1,000^{\circ}C$. The prepared silica fibers were in the shape of circular cross-section and their tensile strength and $SiO_2$ purity were $83{\pm}20kg/mm^2$ and about 99.997%, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.380-386
• /
• 2002

Damage behaviors induced in silicon carbide by an impact of particle having different material and size were investigated. Especially, the influence of the impact velocity of particle on the cone crack shape developed was mainly discussed. The damage induced by spherical impact was different depending on the material and size of particles. Ring cracks on the surface of specimen were multiplied by increasing the impact velocity of particle. The steel particle impact produced larger ring cracks than that of SiC particle. In the case of high velocity impact of SiC particle, radial cracks were produced due to the inelastic deformation at the impact site. In the case of the larger particle impact, the damage morphology developed was similar to the case of smaller particle one, but a percussion cone was farmed from the back surface of specimen when the impact velocity exceeded a critical value. The zenithal angle of cone cracks developed into SiC material decreased monotonically with increasing of the particle impact velocity. The size and material of particle influenced more or less on the extent of cone crack shape. An empirical equation, $\theta$= $\theta$$\sub$st/, v$\sub$p/(90-$\theta$$\sub$st/)/500 R$\^$0.3/($\rho$$_1$/$\rho$$_2$)$\^$$\frac{1}{2}$/, was obtained as a function of impact velocity of the particle, based on the quasi-static zenithal angle of cone crack. It is expected that the empirical equation will be helpful to the computational simulation of residual strength in ceramic components damaged by the particle impact.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.157-164
• /
• 2011

This work is devoted to the technique application of lock-in infrared Thermography in the shipbuilding and ocean engineering industry. For this purpose, an exploratory study to find the optimized test conditions is carried out by the design of experiments. It has been confirmed to be useful method that the phase contrast images were quantified by a reference image and weighted by defect hole size. Illuminated optical intensity of lower or medium strength give a good result for getting a phase contrast image. In order to get a good phase contrast image, lock-in frequency factors should be high in proportion to the illuminated optical intensity. The integration time of infrared camera should have been inversely proportional to the optical intensity. The other hand, the difference of specimen materials gave a slightly biased results not being discriminative reasoning.