• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.289-293
• /
• 2003

This study dealt with the characterization of $MoSi_2$ based composites containing three types of additive materials such as SiC, $NbSi_2\;and\;ZrO_2$ particles have been investigated, based on the detailed examination of their microstructures and fracture surfaces. The effects of reinforcing materials on the high temperature strength of $MoSi_2$ based composites have been also examined. $MoSi_2$ based composites were fabricated by the hot press process under the vacuum atmosphere. The volume fraction of reinforcing materials in the composite system was fixed as 20 %. The microstructures and the mechanical properties of $MoSi_2$ based composites were investigated by means of SEM, EDS, XRD and three point bending test.

• Korean Journal of Materials Research
• /
• v.29 no.6
• /
• pp.392-397
• /
• 2019

A cold roll-bonding process is applied to fabricate an AA6061/AA5052/AA6061 three-layer clad sheet. Two AA6061 and one AA5052 sheets of 2 mm thickness, 40 mm width, and 300 mm length are stacked, with the AA5052 sheet located in the center. After surface treatment such as degreasing and wire brushing, sample is reduced to a thickness of 1.5 mm by multi-pass cold rolling. The rolling is performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 400 mm at rolling speed of 6.0 m/sec. The roll bonded AA6061/AA5052/AA6061 complex sheet is then hardened by natural aging(T4) and artificial aging(T6) treatments. The microstructures of the as-roll bonded and age-hardened Al complex sheets are revealed by optical microscopy; the mechanical properties are investigated by tensile testing and hardness testing. After rolling, the roll-bonded AA6061/AA5052/AA6061 sheets show a typical deformation structure in which grains are elongated in the rolling direction. However, after T4 and T6 aging treatment, there is a recrystallization structure consisting of coarse equiaxed grains in both AA5052 and AA6061 sheets. The as roll-bonded specimen shows a sandwich structure in which an AA5052 sheet is inserted into two AA6061 sheets with higher hardness. However, after T4 and T6 aging treatment, there is a different sandwich structure in which the hardness of the upper and lower layers of the AA6061 sheets is higher than that of the center of the AA5052 sheet. The strength values of the T4 and T6 age-treated specimens are found to increase by 1.3 and 1.4 times, respectively, compared to that value of the starting material.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.2
• /
• pp.117-126
• /
• 2021

An experimental study was carried out to investigate the applicability of cement-based materials for green soil which is a soil for promoting plant growth. The results show that the shear strength of the green soil mixed with gypsum cement (No.3) was low, but the hardness (23.6mm) and pH value (7.4) was most suitable for the vegetation environment. In addition, the initial vegetation germination of green soil, which improved performance by adding a moisturizer, was slower than that of general green soil, and the conductivity value tended to be slightly higher. On the other hand, the slope adhesion of advanced green soil was high, and it was found that the plant growth rate and the regeneration capacity were superior after time passed.

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.50-55
• /
• 2022

SiC is a power semiconductor with a wide bandgap, high insulation failure strength, and thermal conductivity, but many deep-level defects. Defects that appear in SiC can be divided into two categories, defects that appear in physical properties and interface traps that appear at interfaces. In this paper, Z_1/2 trap concentration 0 ~ 9×10¹⁴ cm^-3 reported at room temperature (300 K) is applied to SiC substrates and epi layer to investigate turn-on characteristics. As the trap concentration increased, the current density, Shockley-read-Hall (SRH), and Auger recombination decreased, and Ron increased by about 550% from 0.004 to 0.022 mohm.

• Journal of Korea Foundry Society
• /
• v.41 no.3
• /
• pp.241-251
• /
• 2021

7000-series aluminum alloys are noted for their superior strength compared with other Al alloys, and their billets are generally fabricated by direct-chill (DC) casting. Surface defects in a DC-cast aluminum billet are mainly related to exudation and the meniscus freezing phenomenon, which are influenced by alloy compositions, casting speed, and casting temperature. 7000-series aluminum alloys have a wide freezing range during solidification, which makes it easy for casting defects to occur. In this study, we investigated surface defect evolution in casting billets of Al-8Zn-2Mg-2Cu alloy fabricated by a DC casting process. The billets showed "wavy" or "dotted" surfaces. The wavy surface was formed by meniscus freezing at a lower casting speed (200 mm/min) and temperature (655 ℃). In the wavy surface, refined dendritic cells were observed in a concave region due to the constitutional supercooling caused by meniscus freezing. Meanwhile, at a higher casting temperature (675 ℃), the dotted surface was formed by pore formation. In the dotted surfaces in the billet formed at a high casting speed (230 mm/min), an exudation layer was formed by the high metallostatic head pressure. The dotted region and the smooth region had a refined dendritic morphology and a columnar morphology at the exudation layer, respectively. This is attributed to the formation of gas pores in the dotted region.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.294-297
• /
• 2007

Due to their low densities and high specific strength and stiffness, magnesium alloy sheets are very attractive lightweight materials for automotive and electrical products. However, the magnesium alloy sheets are usually formed at elevated temperature because of their poor formability at room temperature. To use of the magnesium alloy sheets for an industrial, their mechanical properties at elevated temperature and appropriate forming process conditions have to be developed. In this study, non-isothermal simulations of a square cup drawing from magnesium alloy sheets have been conducted to evaluate a proper forming process conditions such as the tool temperature, the tool shoulder radius, friction between the blank and the tools. According to this study, appropriate forming process conditions of square cup drawing at elevated temperature from magnesium alloy sheets are suggested.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2009.11a
• /
• pp.261-264
• /
• 2009

강재의 고강도화는 원자재 부족을 해결할 수 있는 방안으로 친환경적이며 인간의 문명을 지속가능하게 하는 방법으로 인식 되고 있다. 따라서 본 연구에서는 고강도 강재의 횡구속 능력을 평가하기 위해 나선철근을 사용한 횡구속실험을 수행하였다. 실험의 주변수는 단면형상, 철근비로 하고 콘크리트의 강도는 25MPa로 계획하였다. 실험 결과, 단면형상에 따라 원형 실험체가 각형 실험체보다 우수한 횡구속 효과를 나타내는 것을 확인하였다. 또한 횡보강근의 철근비가 증가할수록 횡구속 효과가 증가하는 경향을 나타내었다.

• Textile Coloration and Finishing
• /
• v.23 no.4
• /
• pp.298-303
• /
• 2011

Aramid fibers have been widely used as the reinforcement for composites due to their high modulus and strength. Nowadays the safety measures is required to improve the personal protection. The dyeing of aramid fibers is considered to be very difficult and their dyeing mechanism is not well illucidated. Therefore, this study is to establish the dyeing & printing technology for aramid fibers. The effects of swelling agent and neutral salt in the dye bath on the obtained colors were studied. Also dyeing method of aramid fibers depending on dyeing temperature and dye concentration were established. Color fastness of the dyed aramid fabric with cationic dyes were acceptable excluding light fastness.

• Electronics and Telecommunications Trends
• /
• v.33 no.1
• /
• pp.123-130
• /
• 2018

Tactile sensors, which are commonly referred to as pressure and strain sensors, have been extensively investigated to meet the demands for attachable and wearable electronics for monitoring the health status or activity of human users. For this purpose, the introduction of two-dimensional (2D) materials such as graphene and transition metal dichalcogenides (TMDs) with high mechanical strength at the atomic scale is very suitable for tactile sensors applicable for use in human-friendly devices. In this paper, we examine a descriptive summary of a tactile sensor and review state-of- the-art research trends of 2D material-based tactile sensors in terms of the material and architecture. Finally, we propose a roadmap for future studies into advanced tactile sensors based on our ongoing research.

• Transactions of Materials Processing
• /
• v.26 no.2
• /
• pp.121-126
• /
• 2017

The hot stamping process is an innovative forming method that could prevent the cracking of high strength steel sheets. The formability test of boron steel sheet using forming limit diagrams at elevated temperature is very complicated and time consuming job. In this paper, an alternative test method to evaluate the formability of boron steel in hot stamping has proposed. It measured the FLD0 instead of whole strain combinations of FLD with the tensile test machine and specially designed test rig. Test results shows that the proposed test method can simulate the plain strain condition fracture and can make the FLD of boron steel sheet at elevated temperature with less effort.