• 전자공학회논문지A
• /
• 제33A권5호
• /
• pp.55-64
• /
• 1996

This paper presents performance evaluation of a new high speed inter-processor communication(HIPC) network for large capacity and high performance digitral switching system. The HIPC structure implements the fast reservation and concurrent arbitration technique (modified round-robin arbitration). The performance evaluation of HIPC was performed by not only computer simulation but also numerical approximation method which was derived for a single server multi-queue system with nonexhaustive cyclic service. The approximation results are almost same with that of computer simulation. The TDX-10 basic callscenario was applied to the HIPC netowrk and analyzed. these results were compared with TDX-10 IPC and shows that the difference of th emean waiting time in the TX buffer of NTP node increases sharply according to the increase of the message arrival rate.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1442-1444
• /
• 2000

High speed switching action of PWM inverter is being further advanced for electric motor vehicles. Due to this high speed switching action, extensive high frequency electromagnetic noise emerges. Therefore counterm-easures against electromagnetic interference of electric motor vehicles become increasingly important. This paper describes the theory and countermeasure principle of EMI prevention and EMI test method for Korean Standard EMU.

• Journal of electromagnetic engineering and science
• /
• 제6권1호
• /
• pp.62-70
• /
• 2006

This paper presents a new power plane design method incorporating a single geometry derived from a unit cell of photonic bandgap(PBG) structure. This method yields constantly wide suppression of parallel plate resonances from 0.9 GHz to 4.2 GHz and is very efficient to eliminate PCB resonances in a specified frequency region to provide effective suppression of simultaneous switching noise(SSN). It is shown that with only two cells the propagation of unwanted high frequency signals is effectively suppressed, while it could provide continuous return signal path. The measured results agree very well with theoretically predicted ones, and confirm that proposed method is effective for reducing EMI, with measured near-field distribution. The proposed topology is suitable for design of high speed digital system.

• 연구논문집
• /
• 통권27호
• /
• pp.141-151
• /
• 1997

Recently, the importance of electro-multifunction control valve which is digital control valve is increasing day after day. This is due to the demand of that the current industrial world wants the valve having simpler control circuit and higher operation reliability. It is the PWM controlled high speed electronic valve that satisfies the damands of current industrial world. But, the PWM controlled high speed electronic valve has some non-linearity characteristics like as the delay time of switching and the pressure oscillation phenomenon. These characteristics are an obstacle for the control of high speed & high efficiency in control system. Therefore, in this study, we set the studying purpose on analysis of parameter characteristics in solenoid, and on establishment of optimum design technique in high speed solenoid.

• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.868-876
• /
• 1995

This study deals with a position control of an electro-hydraulic servo system which consist of cylinder and high speed on-off valves operated by microcomputer. The merits of PWM control of hydraulic equipment are the robustness of the high spee on-off valve, its low price and the direct control without D/A converter. In the PWM control of high speed on-off valve, the time lag and switching time existing between the input and output signals of valve are considered as demerit points. To get analytical results, the effects of these demerits have to be clarified in detail. The object of this study is to propose a mathematical model for the behavior of high speed on-off valve and to get analytical results of this system. The dynamic characteristics of this system is examined by digital computer simulation analytically and compared with experimental results to varify the proposed mathematical model.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.61-67
• /
• 2000

In switched reluctance motor(SRM) drive, it is necessary to synchronize the stator phase excitation with the rotor position. Therefore the rotor position information is an essential. Usually optical encoders or resolvers are used to provide the rotor position information. These sensors are expensive and are not suitable for high speed operation. In general, the accuracy of the switching angle is dependent upon the resolution of the encoder and the sampling period of the microprocessor. But the region of high speed, switching angles are fluctuated back and forth from the preset values, which are cause by the sampling period of the microprocessor. Therefore, the low cost linear encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is also presented in this paper. It is verified from the experiments that the proposed encoder and logic controller can be a powerful candidate for the practical low cost SRM drive.

• 제어로봇시스템학회논문지
• /
• 제8권4호
• /
• pp.319-326
• /
• 2002

In switched reluctance motor(SRM) drive, it is important to synchronize the stator phase excitation with the rotor position; therefore, the information about rotor position is essential. Generally, optical encoders or resolvers are used to provide the information. However, these sensors are expensive and are not suitable for high-speed operation. The accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor. In the high-speed region, switching angles are fluctuated back and forth out of the preset value, which is caused by the sampling period of the microprocessor. In this paper, a low cost linear encoder suitable far the practical and stable SRM drive is proposed and also the control algorithm to generate the switching signals using a simple digital logic is presented. The validity of the proposed linear encoder with a proper logic controller is verified through the experiments.

• 한국조명전기설비학회지:조명전기설비
• /
• 제7권4호
• /
• pp.51-58
• /
• 1993

리니어 직류 모터의 고속, 고정도 위치제어에 대하여 포물선형 스위칭 함수에 최단시간 제어 방식을 제안하였다.제안한 방식은 간단한 구성으로 최단시간 제어를 실현한기 위하여 뱅-뱅 제어의 절환을 위상면에 설정한 포물선형 스위칭 함수상에서 행하는 것이다. 그러나 시스템의 모델링 오차등에 의하여 슬라이딩 모드를 발생시키므로 최단시간 제어를 위해 반복실험에 의하여 1회의 절환에 의한 뱅-뱅 제어를 실현하였다. 그 후 궤환 제어에 의하여 리니어 직류모터를 목표점에 정지시켰다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.235-240
• /
• 2002

In micro-EBM, it is well blown that RC circuit is suitable for discharge circuit because of its low pulse width and relatively high peak current. To increase machining speed without changing unit discharge energy, charge resistance should be decreased. But, if very low, continuous (or normal) arc discharge occurs, then increases electrode wear and reduces machining speed remarkably. In this paper, RC circuit with transistor is used to micro-EDM. Experimental results show that RC circuit with transistor can cut off continuous (or normal) arc discharge effectively if duty factor and switching period of transistor are set up optimally. Through experiments with varying charge resistance, it can be known that RC circuit with transistor has about two times faster machining speed than that of RC circuit. Especially, it has prominent rise-effect of machining speed in low unit discharge energy, so that a high-quality and high-speed micro-EDM can be realized through RC circuit with transistor.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 추계종합학술대회 논문집(1)
• /
• pp.37-40
• /
• 2000

Multi Protocol Label Switching (MPLS) is a high performance method for forwarding packets (frames) through a network. It enables routers at the edge of a network to apply simple labels to packets (frames). we use MPLS in the core network for internet. MPLS provide high speed switching and traffic engineering in MPLS domain but at the Label Edge Router(LER) there is frequently cell discarding via congestion and buffer management method. It is one of the most important reasons retransmission and congestion. In this paper we propose advanced LER scheme that provide less cell loss rate also efficient network infrastructure.