• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1449-1454
• /
• 2004

For the research, we developed the hardware and software of the measurement system for on-line test and evaluation. The software controls the hardware of the measurement data and acts as a interface between users and the system hardware. In this paper, we studied performances of the auxiliary block for high-speed railway vehicle. In order to performance these works, the conversion system was developed. Using this system, we obtained the important results, such as voltage values for the battery charger and auxiliary block. Also, we diagnosed the faults and performed the evaluation for auxiliary block using the measurement system and data.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.35-41
• /
• 2003

Propagation speeds of turbulent premixed flames have been measured in a pulsed-flame flow reactor which generates flames propagating in nearly isotropic turbulent flow field with U'/$S_L$ ranging from 1.2 to 5.3. The measurement involved a high-speed digital imaging at 1000 frames/second to capture the flame propagation motion. In addition to the flame speed measurements, flame perimeter ratio was measured for comparison. The observed flame propagation speed is high ranging from 5 to 20 times the laminar flame speed for the range of U'/$S_L$. The flames observed at extreme equivalence ratios exhibit intermittent propagation in that only a small fraction of ignited flame kernel resulted in full propagation of the flame. Also, at low equivalence ratios the flame speed decreased substantially even at high turbulence intensities.

• ETRI Journal
• /
• v.43 no.3
• /
• pp.377-388
• /
• 2021

Owing to the difficulties associated with conducting millimeter-wave (mmWave) field measurements, especially in high-speed train (HST) environments, most propagation channels for mmWave HST have been studied using methods based on simulation rather than measurement. In this study, considering a linear cell layout in which base stations are installed along a railway, measurements were performed at 28 GHz with a speed up to 170 km/h in two prevalent HST scenarios: viaduct and tunnel scenarios. By observing the channel impulse responses, we could identify single- and double-bounced multipath components (MPCs) caused by railway static structures such as overhead line equipment. These MPCs affect the delay spread and Doppler characteristics significantly. Moreover, we observed distinct path loss behaviors for the two scenarios, although both are considered line-of-sight (LoS) scenarios. In the tunnel scenario, the path loss exponent (PLE) is 1.3 owing to the waveguide effect, which indicates that the path loss is almost constant with respect to distance. However, the LoS PLE in the viaduct scenario is 2.46, which is slightly higher than the free-space loss.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.1
• /
• pp.111-118
• /
• 1998

The density of fabric is a very important parameter in many fabric production processes. However, in the textile fabrication factories, textile density measurement process has been done inefficiently by handicraft. Thus, exact textile density measurement process is necessary to fabricate high quality textile through weft straighten. In this paper, we propose an automatic textile density measurement system to measure textile density automatically and to improve fabrication efficiency. The proposed system uses cylindrical lens to optically scan the weftl information of the fabric as well as convex lens to enlarge the weft images. The proposed system improves textile quality and provides constant density value to the whole textile range in the high speed fabrication process.

• Journal of the Korea Society of Computer and Information
• /
• v.6 no.4
• /
• pp.104-109
• /
• 2001

In this paper, we designed a 3D shape measuring system with high speed and high measurement resolution using line-shaped sine stripes of a LCD projector We proposed an effective method to improve measurement efficiency for a 3D shape measuring system by finding the deficient shape information areas and recovering the shape information efficiently. We experimentally confirmed the improvement of measurement efficiency. Deficient shape information areas can be inevitably existed in a acquired image caused by the camera view angle and surface shapes of an object. The measurement efficiency is turned out to be improved by extracting these shadow areas and recovering the shape information efficiently using both a variable rated normalization and a variable sized phase recovering windows.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1376-1381
• /
• 2010

In this study, we dealt with an analysis and development of measurement systems for tunnel and slope structures under a high velocity. Deterioration of tunnel and slope structures becomes a critical issue in regard to both safety and economic concerns. Deterioration itself is inevitable, but condition assessment technology and nondestructive evaluation techniques could provide solutions to ensure public safety by means of detecting damage before serious and expensive degradation consequences occur. We reviewed the existing monitoring and maintenance systems of slopes and tunnels and more advanced directions, especially for highways under high-speed vehicles.

• 한국가시화정보학회:학술대회논문집
• /
• 2003.11a
• /
• pp.43-44
• /
• 2003

A 4D-PTV system was constructed. The measurement system consists of three high-speed high-definition cameras, Nd-Yag laser and a host computer. The GA-3D-PTV algorithm was used for completing the measurement system. A horizontal impinged jet flow was measured. The Reynolds number is about 40,000. Spatial temporal evolution of the jet flow was examined and physical properties such as spatial distributions of vorticity and turbulent kinetic energy were obtained with the constructed system.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.371-372
• /
• 2006

In this paper, we propose a method that measures quality of digital correlator. Quality of digital correlator in field of image composition of radio astronomy have as important position for acquisition of radio wave image with high precision. Digital correlator should have wide bandwidth and high precision to study on deep space. Digital correlator, therefore, should be designed to have high speed processing and high precision. But, real time measurement of quality of digital correlator using acquisition data is difficult to compare accuracy of result because digital correlator should process a large quantity of data with high speed. Measurement method of quality, also, has intricate implementation of experiment equipment. this paper present methods that compose experiment equipment without external installation easily and verify quality of digital correlator perfectly.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.691-698
• /
• 2020

In this study, the effects of hydrodynamic interceptors on a high-speed vessel were investigated to identify the operating principle based on experiments. Model tests were performed using a high-speed towing carriage. The resistance, trim and rise of Center of Gravity (CG) of the high-speed vessel were measured for various ship speeds and interceptor heights. As the interceptor height increased, the trim and rise of CG were reduced. In order to quantitatively analyze these phenomena, the pressure at the stern bottom was measured using tactile sensors. The reliability of the measured results from the tactile sensors was verified through repeat tests. The pressure on the stern bottom increased in proportion to the interceptor height, as the interceptor partially blocked the flow there. Then, the trim was reduced. However, as the ship speed increases, the pressure at the location close to the interceptor decreases when the interceptor height is small, leading to increased trim. Therefore, the interceptor height for running attitude control should be carefully determined considering multiple factors in the operating condition of the high-speed planing hull.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.55-65
• /
• 1987

This paper presents the method of piston temperature measurement and its data under various engine operating conditions. In case of high speed engine, the thermocouple wires must be guided from moving piston to stationary place with carful attention. for this purpose L_LINK SYSTEM was made and assembled to a passenger car engine on the test bench and then the piston temperature was successfully measured. The tested engine speed ranged from 1,000 to 4,000 rpm with 500 rpm increments. Not only the effects of engine speed and load on the piston temperature but those of spark timing, detonation, coolant temperature and Reynolds number based on inlet air condition were studied form the measurement obtained by this L_LINK SYSTEM.