• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.135-138
• /
• 2002

High-speed ejection of burnt gases from the resonator cavity is essential for performance optimization of the chemical laser system. Additionally, to maintain the population of lasing species at a level for maximum optical power, the pressure within the cavity must be of order of 10 torr. In the present study, a small-scale ejector was designed and built for parametric study of its performance. High-pressure air was used as a motive gas. Measurements include schlieren visualization and pressure distribution trace near the ejector nozzle and along the diffuser downstream of the ejector. preliminary tests showed performance of the ejector is a function of parameters including mass flow rate and stagnation pressure of the motive gas, ejector nozzle area ratio, throat area of the diffuser downstream of the ejector.

• Korean Journal of Optics and Photonics
• /
• v.31 no.3
• /
• pp.142-147
• /
• 2020

In this paper, we report highly efficient second harmonic generation of continuous-wave Yb fiber lasers incorporating a periodically poled LiTaO₃ device (MgO:PPSLT) as a frequency converter. The seed laser output from a Yb fiber master oscillator using a Fabry-Perot feedback cavity was amplified in a Yb fiber amplifier stage, yielding 28.5 W of linearly polarized output at 1064 nm in a beam with beam quality, M², of ~1.07. Second harmonic generation was achieved by passing the laser beam through MgO:PPSLT. Under optimized conditions, we obtained 11.1 W of green laser output at 532 nm for an incident signal power of 25.0 W at 1064 nm, corresponding to a conversion efficiency of 44.4%. The detailed investigation to find the optimized operating conditions and prospects for further improvement are discussed.

• Korean Journal of Optics and Photonics
• /
• v.20 no.6
• /
• pp.339-345
• /
• 2009

The high power and single mode vertical cavity surface emitting laser(VCSEL)s with photonic crystal structures have been proposed and fabricated by reducing substantially the hole numbers used in the photonic crystal structures. It is found that only six holes enable VCSELs to operate a single mode and the reliability can be enhanced by filling the holes with polyimide. The single mode lasing characteristics were analyzed by varying the oxide aperture and the hole diameter in photonic crystal structures. As a result, the single mode lasing can be stably obtained in the photonic crystal vertical cavity surface emitting lasers.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.561-569
• /
• 2002

Laser has been called a "Quantum Machine" because of its mechanism of generation since the development on July 7,1960.by T.H.Maiman. We can now use this machine as a tool for manufacturing in industries. At present, 45kW CO2 laser, 10kW Nd:YAG laser, 6kW LD pumped YAG laser and 4kW direct diode laser facilities are available for welding a heavy steel plate of 40mm in thickness and for cutting metals at high speed of 140m/min. Laser Materials Processing is no longer a scientific curiosity but a modern tool in industries. Lasers in manufacturing sector are currently used in welding, cutting, drilling, cladding, marking, cleaning, micro-machining and forming. Recently, high power laser diode, 10kW LD pumped YAG laser, 700W fiber laser and excimer laser have been developed in the industrialized countries. As a result of large numbers of research and developments, the modem laser materials processing has been realized and used in all kinds of industries now. In the present paper, metallurgical studies on laser materials processing such as porosity formation, hot cracking and the joint performances of steels and aluminum alloys and dissimilar joint are discussed after the introduction of laser facilities and laser applications in industries such as automotive industry, electronics industry, and steel making industry. The wave towards the use of laser materials processing and its penetration into many industries has started in many countries now. Especially, development of high power/quality diode laser will be accelerate the introduction of this magnificent tool, because of the high efficiency of about 50%, long life time and compact.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.118-119
• /
• 2013

High power, short wavelength red laser diodes (LDs) have attracted significant interests in a variety of fields due to their advantages in terms of reliability, compactness and cost. The higher brightness for human eyes is required, the shorter wavelength like 630 nm is necessary with higher output power. In this respect, LDs are promising as alternative candidates of gas or dye lasers for such applications due to their small size, high optical/electrical power conversion efficiency, robustness and so on. The crystalline quality of GaInP-AlGaInP multiple quantum wells (MQWs) and AlInP cladding layers is a crucial part in the device performance of GaInP red LDs. Here, we first investigated the effect of Si diffusion on the optical properties of GaInP-AlGaInP MQWs grown with different growth temperatures. Secondary ion mass spectroscopy (SIMS) measurements revealed that both the Mg and Si diffusion into MQW active region was significant. To reduce such diffusion, we employed undoped Mg and Si diffusion barrier and could improve the properties.Without both Mg and Si diffusion barriers, no lasing emission was observed. However, lasing emission was observed clearly for the red LDs with both Mg and Si diffusion barriers. We then investigated the temperature dependent optical properties of MQW layers grown with different well thicknesses (6, 8 and 10 nm). When the well thickness was 10 nm, the better crystalline quality was obtained. However, the observed LD performances were similar, probably due to the defects and impurities in the AlGaInP layer. Further investigation with the detailed analyses will be presented later.

• Laser Solutions
• /
• v.11 no.4
• /
• pp.7-12
• /
• 2008

Laser Transformation Hardening(LTH) is one branch of the laser surface modification processes. A lot of energy is needed for the LTH process to elevate workpiece surface to temperature of the austenite transformation($A_3$), which results from utilizing a beam with a larger size and lower power density comparatively. This study is related to the surface hardening for the rod-shaped carbon steel by the high power diode laser whose beam absorptivity is better than conventional types of lasers such as $CO_2$ or Nd:YAG laser. Because a beam proceeds on the rotating specimen, the pretreated hardened-phase can be tempered and softened by the overlapping between hardened tracks. Accordingly, the longitudinal hardness measurement and observation of the micro structure was carried out for an assessment of the hardening characteristics. In addition, a hardening characteristics as a hardenability of materials was compared in the point of view of the hardness distribution and hardening depth and width.

• Korean Journal of Optics and Photonics
• /
• v.13 no.4
• /
• pp.347-355
• /
• 2002

We have constructed a high efficiency and broad tunable cw Ti:sapphire laser with a four-mirror symmetric Z-type laser cavity to increase the laser usability. From theoretical analyses and experimental data for a symmetric Z-type laser cavity containing a Kerr medium, the cavity mode size and the Kerr-lens mode-locking (KLM) strength for KLM lasers can be confirmed as function of the position in the cavity, the intracavity laser power, and the stability parameter. As a result, the slope efficiency and the maximum average output power of cw Ti:sapphire laser at 5 W pumping power of Ar-ion laser were 31.3% and 1420 ㎽ respectively. The tunablility was ranged from 730 ㎚ to 908 ㎚ with average output power above 700 ㎽. We obtained the KLM operation easily by self-aperturing effect in the Kerr medium and the slope efficiency and the maximum average output power of KLM Ti:sapphire laser was 16% and 550 ㎽ respectively. The spectral bandwidth was 33 ㎚ at the center wavelength of 807 ㎚ and the pulse width was 27 fs with a repetition rate of 82 ㎒.

• Journal of Welding and Joining
• /
• v.20 no.2
• /
• pp.95-101
• /
• 2002

After high power lasers are avaliable in the commercial market, the number of applications of the laser welding has been increased in manufacturing industries. Although the tailored blank laser welding of butt jointed steel sheets is well known recently in the automotive industries, the lap joint laser welding is a new technology to the automotive manufacturing people as well as the design people. But the deep penetration laser welding seems to be preferred to the partial penetration welding for the lap joint welding in the automotive manufacturers because the partial penetration is a serious deflect for the butt joint. In this study, the feasibility of partial penetration welding fur the lap joint $CO_2$ laser welding was studied fur the 1mm thick 390MPa high strength steel sheets for automotive bodies. The process window of the lap joint partial penetration welding was obtained from experiments with the gap size and the welding speed as process parameters. The partial penetration welding was found excellent on the basis of the tensile shear strength and sectional geometry. The bead width, input energy Per volume, tensile-shear strength, deformation energy and the sectional geometries after tensile-shear tests of partial penetration welded specimens are compared with those of full penetration welded specimens with a series of gaps and welding speeds.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1780-1781
• /
• 2011

There have been numerous studies on application of robots to in-pipe inspection system. In this thesis, a mobile robot that can move through elbows and vertical pipes having diameter 100mm is developed. Defect detection technology for locating wall-thinnings, corrosions and foreign materials is developed for high temperature and pressure pipings in thermal power plants, utilizing laser sensors installed on the robot. Actual defect detection performance is evaluated with application of the developed robot system to a mock-up pipings.

• Current Optics and Photonics
• /
• v.7 no.1
• /
• pp.90-96
• /
• 2023

We numerically solve the nonlinear Schrödinger equation for pulse propagation in a passively mode-locked Yb:KGW laser. The soliton-like pulse formation as a result of balanced negative group-delay dispersion (GDD) and nonlinear self-phase modulation is analyzed. The cavity design and optical parameters of a previously reported high-power Yb:KGW laser were adopted to compare the simulation results with experimental results. The pulse duration and energy obtained by varying the small-signal gain or GDD reproduce the overall tendency observed in the experiments, demonstrating the reliability and accuracy of the model simulation and the optical parameters.