• Economic and Environmental Geology
• /
• v.55 no.1
• /
• pp.97-109
• /
• 2022

This study focused on the physicochemical effects of bottom ash dissolved precipitation on the soil and groundwater environment. The iced column and percolation experiments showed that most of the bottom ash particles were drained as the ash-dissolved solution, while the charcoal powder was filtered through the soil. Ion species of Al, As, Cu, Cd, Cr, Pb, Fe, Mn, Ca, K, Si, F, NO₃, SO₄ were analyzed from the eluates collected during the 24 h column test. In the charcoal powder eluates, a high concentration of K was detected at the beginning of the reaction, but it decreased with time. The concentrations of Al and Ca were observed to increase with time, although they existed in trace amount. In the bottom ash eluates, the concentrations of Ca and SO₄ decreased by 30 mg·L^-1 and 67 mg·L^-1, respectively, over 24 h. It is regarded that the infiltration patterns of the bottom ash and biochar in the unsaturated zone were different owing to their particle sizes and solvent properties. It is expected that a significant amount of the bottom ash will mix with the precipitation and percolate below the water table, especially in the case of thin and highly permeable unsaturated zone. The biochar was filtered through the unsaturated zone. The biochar did not dissolve in the groundwater, although it reached the saturation zone. For these reasons, it is considered that the direct contamination by the bottom ash and biochar are unlikely to occur.

• Journal of Appropriate Technology
• /
• v.7 no.2
• /
• pp.136-143
• /
• 2021

Pacific island countries, including Kiribati, are suffering from a shortage of essential resources as well as a reduction in their living space due to sea level rise and coastal erosion from climate change, groundwater pollution and vegetation changes. Global activities to solve these problems are being progressed by the UN's efforts to implement SDGs. Pacific island countries can adapt to climate change by using abundant marine resources. In other words, seawater plants can assist in achieving SDGs #2, #6 and #7 based on SDGs #14 in these Pacific island countries. Under the auspice of Korea International Cooperation Agency (KOICA), Korea Research Institute of Ships and Ocean Engineering (KRISO) established the Sustainable Seawater Utilization Academy (SSUA) in 2016, and its 30 graduates formed the SSUA Kiribati Association in 2017. The Ministry of Oceans and Fisheries (MOF) of the Republic of Korea awarded ODA fund to the Association. By taking advantage of seawater resource and related plants, it was able to provide drinking water and vegetables to the local community from 2018 to 2020. Among the various fields of education and practice provided by SSUA, the Association hope to realize hydroponic cultivation and seawater desalination as a self-support project through a pilot project. To this end, more than 140 households are benefiting from 3-stage hydroponics, and a seawater desalination system in connection with solar power generation was installed for operation. The Association grows and supplies vegetable seedlings from the provided seedling cultivation equipment, and is preparing to convert to self-support business from next year. The satisfaction survey shows that Tarawa residents have a high degree of satisfaction with the technical support and its benefits. In the future, it is hoped that SSUA and regional associations will be distributed to neighboring island countries to support their SDGs implementations.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.57 no.4
• /
• pp.316-333
• /
• 2021

In order to understand basic data for improving the fishing system and fishing vessel structure in coastal improved stow net fishery, a questionnaire survey and on-site hearing were conducted from May 10 to June 11, 2019 to analyze opinions on the improvement of operation status and fishing vessel structure. The questionnaire survey consisted of ten questions on the operation status of coastal improved stow net fishery and six questions on the improvement of fishing vessel structure, and the results of each question were analyzed by the region, the captain's age, the captain's career and the age of fishing vessel. As a result of analyzing opinions on the operation status of the coastal improved stow net fishery, it was found that the average time required for casting net was 32.8 to 33.0 minutes and that the average time required for hauling net was 41.0 to 42.2 minutes which took 10 to 12 minutes more than for casting net. The most important work requiring improvement during fishing operation (the first priority) were 'hauling net operation,' 'readjustment and storage of fishing gear,' and 'fish handling' and the hardest factor in fishing management were in the order of 'reduction of catch,' 'labor shortage' and 'rising labor costs.' The most institutional improvement that is most needed in coastal improved stow net fishery was an 'using fine mesh nets.' Most of the respondent to the questions on the experience in hiring foreign crews was 'either hiring or willing to hire foreign crews,' and the average number of foreign crews employed was found to be 2.3 to 2.4 persons. The most important reason for hiring (or considering employment) foreign crews was 'high labor costs.' The degree of communication with foreign crews during fishing operation were 'moderate' or 'difficult to direct work.' The most important problem in hiring foreign crews (the first priority) was an 'illegal departure.' As the survey results on the opinion of structural improvement of coastal improved stow net fishing vessel, the degree of satisfaction with fishing vessel structure related to fishing operation was found to be somewhat unsatisfactory, with an average of 3.3 points on a five-point scale. The inconvenient structure of fishing vessel in possession (the first priority), the space needed most for the construction of new fishing vessel (the first priority) and the space considered important for the construction of new fishing vessel (the first prioprity) was a 'fish warehouse.' The most preferred equipment for the construction of new fishing vessel were 'engine operation monitoring' and 'navigation safety devices.' The average size (tonnage class), the average horse power and the average total length of fishing vessel for proper profit and safety fishing operation was between 13.8 and 14.0 tonnes, 808.3 to 819.5 H.P. and 23.4 to 23.5 meters, respectively. The results of the operation status of coastal improved stow net fishery and the requirement for improving the fishing vessel structure are expected to be provided as basic data for reference when we build or improve the fishing vessel.

• Journal of Applied Biological Chemistry
• /
• v.65 no.3
• /
• pp.129-142
• /
• 2022

Ginseng sprouts, which can be eaten from leaves to roots, has the advantage of not having to use pesticides without being affected by the season by using smart farms. The optimal cultivation timing of sprout ginseng was checked and the nutritional content and antioxidant activity were compared and analyzed. The values of total fatty acids and total minerals were no significant changes during the growth periods. The contents of total amino acids were slightly decreased to 45 days and after increased to 65 days. When the growth period was 65 days, arginine had the highest content of 3309.11 mg/100 g. The total phenolic contents were high at 3.73 GAE mg/g on the 45 days, and the total flavonoid contents were also the highest at 9.04 RE mg/g on the 45 days. The contents of total ginsenoside was not noticeable for the growth periods (29.83 on 25 days→32.77 on 45 days→26.02 mg/g on 65 days). The ginsenoside Rg2 (0.62 mg/g), Re (8.69 mg/g), Rb1 (4.75 mg/g) and Rd (3.47 mg/g) had highest contents on 45 days during growth. The values of phenolic acids and flavonols were gradually increased to 45 days (338.6 and 1277.14 ㎍/g) and then decreased to 65 days. The major compounds of phenolic acids and flavonols were confirmed to benzoic acid (99.03-142.33 ㎍/g) and epigallocatechin (416.03-554.64 ㎍/g), respectively. The values of 2,2-diphenyl-1-picrylhydrazyl (44.27%), 2,4,6-azino-bis (3-ethylbenzothiazoline-6-sulphnoic acid) diammonium salt (75.16%), and hydroxyl (63.29%) radical scavenging activities and ferric reducing/antioxidant power (1.573) showed the highest activity on the 45 days as well as results of total phenolic and total flavonoid contents.

• Journal of Bio-Environment Control
• /
• v.31 no.3
• /
• pp.180-187
• /
• 2022

In order to select suitable light in a plant factory, electric energy use efficiency and light use efficiency should be considered simultaneously to consider operating costs as well as quantitative and functional aspects. The growth characteristics, electric energy use efficiency, light use efficiency by light intensity, LED ratio, and photoperiod conditions were compared together. Light intensity is 60, 130, 230, and 320 µmol·m^-2·s^-1 treatments, and light quality is the mixing ratio of red light and blue light 8:2, 6:4, 4:6, and 2:8 treatments. Photoperiod is 9, 12, 15, and 18 hours treatments based on the daytime. In the light intensity experiment, the growth rate increased as the light intensity increased, but there was no significant difference in the light use efficiency. When comparing the leaf fresh weight per power consumption, only the 320 µmol·m^-2·s^-1 treatment group showed significantly low efficiency, and there was no significant difference in the other treatments, so 230 µmol·m^-2·s^-1, which produced the most, was the most efficient. In the light quality experiment, the ratio of red light and blue light was measured to be high at the same time as the growth rate and light use efficiency in RB 8:2, and there was no significant difference in color difference and flavonoids content, so a Red:Blue ratio of 8:2 was the most suitable condition. In the photoperiod experiment, the longer the photoperiod, the higher the growth rate. However, there was no significant difference in the growth rate over 12 hours of daytime, so 12 hours considering the light consumption efficiency was a suitable condition. Based on the above results, LED light environmental conditions for perilla growth in plant factories were light intensity, light quality, and day length of 230 µmol·m^-2·s^-1 or more, 8:2, and 12 hours or more, respectively.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.29 no.4
• /
• pp.67-76
• /
• 2021

Biogasification is a technology that produces environmentally friendly fuel using methane gas generated in the process of stably decomposing and processing organic waste. Biogasification is the most used method for energy conversion of organic waste with high moisture content, and is a useful method for organic waste treatment following the prohibition of direct landfill (2005) and marine dumping (2013). Due to African Swine Fever (ASF), which recently occurred in Korea, recycling of wet feed is prohibited, and consumers such as dry feed and compost are negatively recognized, making it difficult to treat food waste. Accordingly, biogasification is attracting more attention for the treatment and recycling of food waste. Korea's energy consumption amounted to 268.41 106toe, ranking 9th in the world. However, it is an energy-poor country that depends on foreign imports for about 95.8% of its energy supply. Therefore, in Korea, the Renewable Energy Portfolio Standard (RPS) is being introduced. The domestic RPS system sets the weight of the new and renewable energy certificate (REC, Renewable energy certificate) of waste energy lower than that of other renewable energy. Therefore, an additional incentive system is required for the activation of waste-to-energy. In this study, the operation of an anaerobic digester that treats food waste, food waste Leachate and various organic wastes was confirmed. It was intended to be used as basic data for preparing the waste-to-energy incentive system through precise monitoring for a certain period of time. Four sites that produce biogas from organic waste and use them for power generation and heavy gas were selected as target facilities, and field surveys and sampling were conducted. Basic properties analysis was performed on the influent sample of organic waste and the effluent sample according to the treatment process. As a result of the analysis of the properties, the total solids of the digester influent was an average of 12.11%, and the volatile solids of the total solids were confirmed to be 85.86%. BOD and CODcr removal rates were 60.8% and 64.8%. The volatile fatty acids in the influent averaged 55,716 mg/L. It can be confirmed that most of the volatile fatty acids were decomposed and removed with an average reduction rate of 92.3% after anaerobic digestion.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.50 no.4
• /
• pp.20-36
• /
• 2022

This study aims to provide basic data for high-quality street tree management by setting reasonable management items and appropriate unit prices by reviewing the adequacy of current street tree management. Currently, street tree management items, except for street tree pruning, use general landscape tree quantity per unit for the street tree management quantity per unit. KEPCO (Korea Electric Power Corporation) applied pruning items from standard electric production infrastructure and carried out the activities at an average unit price of 51% lower for heavy pruning and 39% lower for light pruning than the standard estimate. This was judged to be a level that could not maintain or increase the quality of street tree management. It was determined that an appropriate standard unit price for street tree management was necessary. To improve the quantity per unit for the proper management of street trees, it was necessary to review costs in the field. However, due to the absence of data on actual construction costs in the domestic landscape field, detailed items of the US RSMeans Building Construction Cost Data (RSMeans) were reviewed, and the actual construction costs were calculated by applying personal domestic expenses. As a result, the standard of the estimated unit showed a good ratio of 107% for heavy pruning of street tree pruning compared to the actual construction cost, but light pruning was underestimated with a 59% ratio. Shrub pruning was 82%, weeding was 92%, tree fertilization was 87%, and windbreak wall installation was 91% under-engineered. In addition, it was also confirmed that the watering by sprinkler trucks and chemical spraying were over-designed compared to the actual construction cost at the rates of 118% and 124%, respectively. Due to the specificity of the street trees, the increase in personal expenses and the input cost of equipment, such as road safety controls, were judged to be the main cause of the underestimation of items. Therefore, it is necessary to add items related to street trees and general landscape trees to the landscape maintenance items of the standard of the estimated unit.

• Clean Technology
• /
• v.29 no.3
• /
• pp.193-199
• /
• 2023

Biomass has been used to secure renewable energy certificates (REC) in domestic and overseas coal-fired power plants. In recent years, biofuel has been diversified from traditional wood pellets to non-woody biomass. Non-woody biomass has a higher content of alkaline metals such as K and Na than wood-based biomass, resulting in a lower melting point and an increase in slagging on boiler tubes, which reduces boiler efficiency. This study analyzed the effect of kaolin, an additive commonly used to increase melting points, on biomass co-firing to coal through thermochemical equilibrium calculations. In a previous experiment on biomass co-firing to coal conducted at 80 kW_th, it was interpreted that the use of kaolin actually increased the amount of fouling. In this study, analysis showed that when kaolin was added, aluminosilicate compounds were generated due to Al₂O₃, which is abundant in coal, and mullite was formed. Thus, it was confirmed that the amount of slag increased when more kaolin was used. Further analysis was conducted by increasing the biomass co-firing rate from 0% to 100% at 10% intervals, and the results showed non-linear liquid slag generation. As a result, it was found that the least amount of liquid slag was generated when the biomass co-firing rate was between 50 and 60%. The phase diagram analysis showed that high melting point compounds such as leucite and feldspar were most abundantly generated under these conditions.

• Journal of the Daesoon Academy of Sciences
• /
• v.41
• /
• pp.63-131
• /
• 2022

In the context of Daesoon Jinrihoe's The Canonical Scripture, 'Saving Lives' consists of one 44 verse-long chapter. The content covers Kang Jeungsan's authority and foreknowledge, and most of the passages are about the treatment of diseases. Other passages are about relief from natural disasters, the resolution of conflicts in personnel affairs, and wisdom as applied to saving lives. The treatment of diseases focuses on solving the ailments faced by lower classes during that time period. Kang Jeungsan relieved the damage suffered by the people from natural phenomena as caused by the three disasters which resulted from water, fire, and wind. He also worked to solve other difficulties experienced in human society. In addition, the definition of 'wisdom' here is one of being high-seeing and far-thinking in Saving Lives. That is the foundation upon which wisdom can save oneself and others. After comparing each chapter of The Canonical Scripture with the parallel verses from the 6th edition of Daesoon Jeongyeong, the results of this study can be summarized as follows: first, saving lives as performed by Kang Jeungsan became an unprecedented and absolute act of relieving the common people during a time when they were suffering from great harms, hardships, and difficulties in their daily lives during the late Joseon Dynasty. Second, the verses were distributed into seven parts to achieve the purpose indicated by the titles of each section which related to specific powers exhibited by Kang Jeungsan in his interactions with Heaven, Earth and Humanity. Third, the second chapter of 'Saving Lives' includes not only treatment of disease, natural disasters, and hardships, but also relief meant to lessen the burdens people experienced in their daily lives while living within the boundaries of society. This is different from the respective section from the 6th edition of Daesoon Jeongyeong which, by way of contrast, only contained verses concerning the treatment of disease. The contents of 'Saving Lives' in The Canonical Scripture deals with the relief in a wide range of applications and is thereby different from the chapter on healing from the Daesoon Jeongyeong, which merely dealt with the healing of diseases. Therefore, this broader range of meanings can be taken to be a unique feature of The Canonical Scripture.

• Korea Science and Art Forum
• /
• v.20
• /
• pp.147-158
• /
• 2015

This study made an approach to the industrial exhibition space, which is a medium of marketing communication, from the position of an enterprise and consumers through the output of Space Design, and conducted it with focus on B2B transactions among specialized exhibitions. In addition, this study inquired into what factors should be considered along with space design by interpreting the purpose of participating in the exhibition and space design of the enterprise which supply capital goods, elements, related technologies and materials, etc. This study aimed at drawing the direct/indirect effect, produced by space design, on the marketing by analyzing correlation between space design and participating enterprises' marketing. Despite the marketing effect of the exhibition, which was proved by preceding research results, the reality is that exhibition-participating expenses work as considerable burden on enterprises. Particularly, booth design, which is forming the most proportion among the participating expenses, was found to have insufficient influence on visitors due to the decline in its importance among diverse factors influencing visitor's decision to visit a booth. Regardless of the business category of participating enterprises in the exhibition, the standard of exhibits was ranked as the most important consideration factor in visiting a booth. Even by business category, the standard of booth design rarely had an influence on booth visit. Booth design had an affirmative influence on participating enterprise's preference, but its influence on product purchase or business talk & contact with a participating enterprise or price was found to be extremely low. It's difficult to judge marketing success or failure of an exhibition by the form and standard of booth design. Preferably, this study infers that it's necessary to put much weight on qualitative excellence of an exhibition, which consists of participation of an enterprise in possession of excellent technologies, exhibits with higher standards and high-quality visitors with purchasing power. This study suggests that it's more effective to set up the plan for expansion of participation in exhibition by optimally regulating the proportion of space design in participating expense to increase marketing effectiveness of an exhibition. The limitations of this study, analysis of which based on the visitors to an exhibition only, requires supplementation through the follow-up research work on participating enterprises in the exhibition.