• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.156-156
• /
• 2016

The effect of nitrogen doping on the mechanical and tribological performance of single-layer tetrahedral amorphous carbon (ta-C:N) coatings of up to $1{\mu}m$ in thickness was investigated using a custom-made filtered cathode vacuum arc (FCVA). The results obtained revealed that the hardness of the coatings decreased from $65{\pm}4.8GPa$ to $25{\pm}2.4GPa$ with increasing nitrogen gas ratio, which indicates that nitrogen doping occurs through substitution in the $sp^2$ phase. Subsequent AES analysis showed that the N/C ratio in the ta-C:N thick-film coatings ranged from 0.03 to 0.29 and increased with the nitrogen flow rate. Variation in the G-peak positions and I(D)/I(G) ratio exhibit a similar trend. It is concluded from these results that micron-thick ta-C:N films have the potential to be used in a wide range of functional coating applications in electronics. To achieve highly conductive and wear-resistant coatings in system components, the friction and wear performances of the coating were investigated. The tribological behavior of the coating was investigated by sliding an SUJ2 ball over the coating in a ball-on-disk tribo-meter. The experimental results revealed that doping using a high nitrogen gas flow rate improved the wear resistance of the coating, while a low flow rate of 0-10 sccm increased the coefficient of friction (CoF) and wear rate through the generation of hematite (${\alpha}-Fe_2O_3$) phases by tribo-chemical reaction. However, the CoF and wear rate dramatically decreased when the nitrogen flow rate was increased to 30-40 sccm, due to the nitrogen inducing phase transformation that produced a graphite-like structure in the coating. The widths of the wear track and wear scar were also observed to decrease with increasing nitrogen flow rate. Moreover, the G-peaks of the wear scar around the SUJ2 ball on the worn surface increased with increasing nitrogen doping.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.783-791
• /
• 1994

Piezoelectric ZnO thin films were deposited on 7059 glass substrate by rf magnetron sputtering. The effects of deposition parameter, such as rf power, gas pressure and $O_{2}$/Ar gas ratio, on the crystallinity and electrical properties of the deposited ZnO thin films were studied. It was found that the deposition rate was higher than the previously reported values. ZnO films were suitable for SAW filter since a standard deviation of XRD (002) peak rocking curve was less than $6^{\circ}$. ZnO thin films, which were deposited at $O_{2}$/Ar ratio larger than 25%, showed high resistance. SAW filter was fabricated using ZnO film, of which thickness was 0.25 of the wavelength of the propatating surface acoustic wave. The measured frequency response was consistent with the calculated one. The SAW filter had center frequency 39.08 MHz, phase velocity 2501 m/sec and insertion loss 29 dB.

• Advances in materials Research
• /
• v.2 no.4
• /
• pp.209-219
• /
• 2013

We have described primary studies on conductivity and molecular weight of polyaniline separately in the electric and magnetic fields when it is used in a field effect experimental configuration. We report further studies on doped in-situ deposited polyaniline. First we have chemically synthesized polyaniline by ammonium peroxodisulfate in acidic aques and organic solutions at different times. Then we measured mass and conductivity and obtained the best time of polymerizations. In continue, we repeated these reactions separately under different electric and magnetic fields in constant time and measured mass and conductivity. The polyaniline is characterized by gel permeation chromatography (GPC), UV-Visible spectroscopy and electrical conductivity. High molecular weight polyanilines are synthesized under electric field, $M_w$ = 520000-680000 g/mol, with $M_w/M_n$ = 2-2.5. The UV-Visible spectra of polyanilines oxidized by ammonium peroxodisulfate and protonated with dodecylbenzenesulfonic acid (PANi-DBSA), in N-methylpyrolidone (NMP), show a smeared polaron peak shifted into the visible. Electrical conductivity of polyanilines has been studied by four-probe method. The conductivity of the films of emeraldine protonated by DBSA cast from NMP are higher than 500 and 25 S/cm under 10 KV/m of potential) electric field and 0.1 T magnetic field, respectively. It shows an enhanced resistance to ageing too. By the next steps, we carried chemical polymerization at the best electric and magnetic fields at different times. Finally, resulted in finding the best time and amount of the fields. The longer polymerization time and the higher magnetic field can lead to degradation of polyaniline films and decrease conductivity and molecular mass.

• Earthquakes and Structures
• /
• v.16 no.3
• /
• pp.265-277
• /
• 2019

Framed masonry wall structures represent a typical high-rise structural system that are also seismically vulnerable. During ground motions, they are excited in both in-plane and out-of-plane terms. The interaction between the frame and the infill during ground motion is a highly investigated phenomenon in the field of seismic engineering. This paper presents a numerical investigation of two distinct static out-of-plane loading methods for framed masonry wall models. The first and most common method is uniformly loaded infill. The load is generally induced by the airbag. The other method is similar to in-plane push-over method, involves loading of the frame directly, not the infill. Consequently, different openings with the same areas and various placements were examined. The numerical model is based on calibrated in-plane bare frame models and on calibrated wall models subjected to OoP bending. Both methods produced widely divergent results in terms of load bearing capabilities, failure modes, damage states etc. Summarily, uniform load on the panel causes more damage to the infill than to the frame; openings do influence structures behavior; three hinged arching action is developed; and greater resistance and deformations are obtained in comparison to the frame loading method. Loading the frame causes the infill to bear significantly greater damage than the infill; infill and openings only influence the behavior after reaching the peak load; infill does not influence initial stiffness; models with opening fail at same inter-storey drift ratio as the bare frame model.

• Korean Journal of Materials Research
• /
• v.33 no.12
• /
• pp.517-524
• /
• 2023

BaTiO₃-Poly vinylidene fluoride (PVDF) solution was prepared by adding 0~25 wt% BaTiO₃ nanopowder and 10 wt% PVDF powder in solvent. BaTiO₃-PVDF film was fabricated by spreading the solution on a glass with a doctor blade. The output performance increased with increasing BaTiO₃ concentration. When the BaTiO₃ concentration was 20 wt%, the output voltage and current were 4.98 V and 1.03 ㎂ at an applied force of 100 N. However, they decreased when the over 20 wt% BaTiO₃ powder was added, due to the aggregation of particles. To enhance the output performance, the generator was poled with an electric field of 150~250 kV/cm at 100 ℃ for 12 h. The output performance increased with increasing electric field. The output voltage and current were 7.87 V and 2.5 ㎂ when poled with a 200 kV/cm electric field. This result seems likely to be caused by the c-axis alignment of the BaTiO₃ after poling treatment. XRD patterns of the poled BaTiO₃-PVDF films showed that the intensity of the (002) peak increased under high electric field. However, when the generator was poled with 250 kV/cm, the output performance of the generator degraded due to breakdown of the BaTiO₃-PVDF film. When the generator was matched with 800 Ω resistance, the power density of the generator reached 1.74 mW/m². The generator was able to charge a 10 ㎌ capacitor up to 1.11 V and turn on 10 red LEDs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.68.1-68.1
• /
• 2012

The best part of graphene is - charge-carriers in it are mass less particles which move in near relativistic speeds. Comparing to other materials, electrons in graphene travel much faster - at speeds of $10^8cm/s$. A graphene sheet is pure enough to ensure that electrons can travel a fair distance before colliding. Electronic devices few nanometers long that would be able to transmit charge at breath taking speeds for a fraction of power compared to present day CMOS transistors. Many researches try to check a possibility to make it a perfect replacement for silicon based devices. Graphene has shown high potential to be used as interconnects in the field of high frequency electrical devices. With all those advantages of graphene, we demonstrate characteristics of electrical and optical properties of graphene such as the effect of graphene geometry on the microwave properties using the measurements of S-parameter in range of 500 MHz - 40 GHz at room temperature condition. We confirm that impedance and resistance decrease with increasing the number of graphene layer and w/L ratio. This result shows proper geometry of graphene to be used as high frequency interconnects. This study also presents the optical properties of graphene oxide (GO), which were deposited in different substrate, or influenced by oxygen plasma, were confirmed using different characterization techniques. 4-6 layers of the polycrystalline GO layers, which were confirmed by High resolution transmission electron microscopy (HRTEM) and electron diffraction analysis, were shown short range order of crystallization by the substrate as well as interlayer effect with an increase in interplanar spacing, which can be attributed to the presence of oxygen functional groups on its layers. X-ray photoelectron Spectroscopy (XPS) and Raman spectroscopy confirms the presence of the $sp^2$ and $sp^3$ hybridization due to the disordered crystal structures of the carbon atoms results from oxidation, and Fourier Transform Infrared spectroscopy (FTIR) and XPS analysis shows the changes in oxygen functional groups with nature of substrate. Moreover, the photoluminescent (PL) peak emission wavelength varies with substrate and the broad energy level distribution produces excitation dependent PL emission in a broad wavelength ranging from 400 to 650 nm. The structural and optical properties of oxygen plasma treated GO films for possible optoelectronic applications were also investigated using various characterization techniques. HRTEM and electron diffraction analysis confirmed that the oxygen plasma treatment results short range order crystallization in GO films with an increase in interplanar spacing, which can be attributed to the presence of oxygen functional groups. In addition, Electron energy loss spectroscopy (EELS) and Raman spectroscopy confirms the presence of the $sp^2$ and $sp^3$ hybridization due to the disordered crystal structures of the carbon atoms results from oxidation and XPS analysis shows that epoxy pairs convert to more stable C=O and O-C=O groups with oxygen plasma treatment. The broad energy level distribution resulting from the broad size distribution of the $sp^2$ clusters produces excitation dependent PL emission in a broad wavelength range from 400 to 650 nm. Our results suggest that substrate influenced, or oxygen treatment GO has higher potential for future optoelectronic devices by its various optical properties and visible PL emission.

• Parasites, Hosts and Diseases
• /
• v.29 no.1
• /
• pp.67-86
• /
• 1991

In order to determine the seasonal prevalence and population dynamics of Culex tritaeniorhynchus in relation to the epidemics of Japanese encephalitis, and ecology of these vector mosquito in Kyungpook Province, Korea, studies were con- ducted during the Period of 7 years from 1984 to 1990. Cx. tritaeniorhynchus first collected in June between 4th and 28th, and trapped in large numbers during the period from mid-August to early September, showed a simple sharply pointed one-peaked curve. There was a gradual decrease from mid-September, with a very small number of them collected until early October in every year. The average number of Cx. tritaeniorhynchus rapidly decreased after 1985, and the number became particularly low in 1989. The highest population density, which was observed in August during the initial three years, was found to be delayed in the following years, accompanied by a decrease in the number of mosquitoes. In the trend of nocturnal activity of Cx. tritaeniorhynchus, with oncoming darkness they become very active, gradually decreasing in activity toward mid night, but slightly increasing toward dawn. The immature stages of Cx. tritaeniorhynchus were first found in rice fields contributing to peak adult densities in mid-July. The highest average densities of Cx. trisaeniorhynchus was 14,900 per m2 on mid-August 19th. The larval Cx. tritaeniorhynchus showed high resistance levels and resistance ratios against 5 organophosphorus compounds. In the adult horisontal life table characteristics of Kyungsan colonies of Cx. tritaeniorhynchus under insectary condi- tions, life expectancy was 28.3 days for males and 59.8 days for females. The net reproductive rate was 7.8 and generation time was 25.6 days.

• Journal of Welding and Joining
• /
• v.28 no.3
• /
• pp.92-98
• /
• 2010

Ferritic stainless steels, which have relatively small thermal expansion coefficient and excellent corrosion resistance, are increasingly being used in vehicle manufacturing, in order to increase the lifetime of exhaust manifold parts. But, there are limits on use because of the problem related to cosmetic resistance, corrosions of condensation and high temperature salt etc. So, Aluminum-coated stainless steel instead of ferritic stainless steel are utilized in these parts due to the improved properties. In this investigation, Al-8wt% Si alloy coated 409L ferritic stainless steel was used as the base metal during Gas Tungsten Arc(GTA) welding. The effects of coated layer on the microstructure and hardness were investigated. Full penetration was obtained, when the welding current was higher than 90A and the welding speed was lower than 0.52m/min. Grain size was the largest in fusion zone and decreased from near HAZ to base metal. As welding speed increased, grain size of fusion zone decreased, and there was no big change in HAZ. Hardness had a peak value in the fusion zone and decreased from the bond line to the base metal. The highest hardness in the fusion zone resulted from the fine re-precipitation of the coarse TiN and Ti(C, N) existed in the base metal during melting and solidification process and the presence of fine $Al_2O_3$ and $SiO_2$ formed by the migration of the elements, Al and Si, from the melted coating layer into the fusion zone.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.123-130
• /
• 2016

High-frequency induction heating equipment can heat the metal by applying a High-Frequency power to the resonant circuit. The resonance circuit is composed of the work coil and the conduction-cooled power capacitor, it influences the performance of the heat treatment equipment according to the characteristics of the capacitor. However, dependence on conduction-cooled power capacitor's import is high due to lack of core technology research and development. Minimizing the generation of internal heat transmitted inside during LC resonance, reduce the reactive power loss, there is a need for a capacitor within the voltage characteristic outstanding. To implement localization it is vital that prior study of the analysis on the frequency response characteristic for the finished capacitor advanced manufacturer be implemented. Studying the interpolation method to read the value at any point of the characteristic curve for a given log-log scale was applied to the analysis tool of the capacitor by my proposed algorithm. The simulation for reproducing frequency response curves was attempted by assuming a capacitor in a simplified series equivalent RC circuit to obtain the equivalent series resistance value. It was confirmed that the reproduction rate was the result value above 83% as compared to the simulation of the properties and characteristics on the actual reactive power for Peak value, and that the algorithm can be applicable when analyzing and predicting the characteristic curves of a simpled model capacitor.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.119-119
• /
• 2009

인버터 DC 저항용접의 적용성 증대 : 인버터 DC 저항용접 공법이 SPOT, PROJECTON, SEAM, BUTT 등의 공정에 다양하게 적용되어 저항용접 현장에서 고효율, 친환경적 용접 환경을 만드는데 일조 하고 있다. 특히 자동차의 경량화, 충돌내성 증대, 진동 및 내구성 증대, 공간활용 극대화, 새로운 Design 개념 적용 등의 산업전반에 걸쳐 나타나는 신 Trends로 고 장력 철재의 적용 범위가 확대되고 HSS(High Strength Steel), EHSS(Extra High Strength Steel), UHSS (Ultra High strength Steel ; Hot - Formed Steel )등 다양한 철판의 SPOT 저항용접이 필요하게 되었다. 기존의 AC 단상용접의 전력 특성 상 통전 중 무 통전 시간 과 높은 PEAK 전력, 단상 대 전력 소모로 인한 전력 DROP 등의 문제로 인하여 신소재의 용접 시 매우 많은 Spatter가 발생하고, 높은 용접품질의 확보가 어려워 지므로 이를 대체하기 위한 공법으로 MFDC ( 인버터 DC 저항용접공법 )이 적용되고 있다. 인버터 DC 저항용접의 적응제어 : MFDC라는 높은 효율의 용접 전력원이 확보 됨에도 불구하고 용접현장에서는 원 자재, 도금 등의 품질 산포, 프레스 물의 가공산포, 공기압 산포, 전극 과열 및 마모 등의 요인에 의하여 저항용접 산포가 발생하고 있다. 이는 인위적인 조작이 어렵고 불규칙적이며, 어디서나 산재하고 있는 문제이다. 이를 용접전력 제어 법으로 개선하여 일정한 용접성을 확보하기 위한 노력이 적응제어 기법이다. 정 전류, 정 전력 제어는 정량 제어로 용접 물을 비롯한 용접부의 변화와는 관계없이 설정된 일정량의 전력을 공급하기만 하는데 반하여 적응제어는 적절한 용접 작업 시의 용접 물의 상태, 전극의 가압, 표면 상태 등에 따른 변화 페턴을 기억하고 이후 진행되는 용접에 대하여 정상 페턴과의 차이를 감지 이를 보상하므로 고품질의 용접성을 보장하는 제어기법이다. 따라서 다양한 용접 산포 유발 요인에 의해 용접부의 변화가 발생한다 하여도 그 변화를 감지 하고 적절한 용접전력을 공급한다면 고품질의 용접성을 확보하는데 유용한 공법이 될 수 있다. 인버터 DC 저항용접의 SPC 관리 : SPOT 용접 시 획득할 수 있는 다양한 파라메터에 대하여 모니터링 하고 이 자료를 data 화 하여 품질 관리에 응용하게 되면 양산라인에서 반복적으로 발생되는 문제점을 확인 할 수 있고 이를 통계적 방법으로 추적 개선해 나간다면 용접 불량 감소 및 생산성 향상에 도움이 되며 작업자의 공정 능력 향상 및 기업의 기술축적에도 높은 기여를 할 수 있을 것이다. 용접 적응제어와 다양한 파라메터 모니터링이 한 system에서 이루어 질 때 높은 용접성 확보와 불량률 감소, 원가절감, 생산성 향상 등의 효과가 극대화 될 것이다.