• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.741-742
• /
• 2006

This paper deals with an efficient superconducting joint method between 2G high superconducting(HTS) wire, YBCO coated conductor(CC). Recently CC is one of the most promising superconducting wire due to high n-value and critical current independency from external magnetic field. It is expected to be used many superconducting application such as fault current limiter, persistent current system and cable etc. In most HTS applications, superconducting magnet is used, and it is necessary to joint between superconducting wire to fabricate superconducting magnet system. A CC tape used in this research consists of copper stabilizer, silver layer, YBCO layer, buffer and substrate. Direct joint using soldering method was inefficient due to resistance of copper, then copper lamination is removed by chemical etching method to reduce resistance between CC tapes. Jointed tapes were fabricated and tested. Transport current through jointed area and induced voltage were measured to characterize the I-V curve. Resistance between CC wire using chemical etching was compared with resistance of direct jointed tapes using soldering method in this paper.

• 대한전자공학회논문지SD
• /
• 제42권5호
• /
• pp.31-38
• /
• 2005

본 논문에서는, UTMI호환 USB2.0 PHY 칩의 구조와 세부 설계 내용 전반에 대하여 기술하였다. 노이즈 채널 환경에서, 수신데이터의 유효성을 판단하기 위한 방법으로 squelch 상태 검출 회로 및 전류모드 슈미트-트리거 회로를 설계하였으며, 레플리카 바이어스 회로를 사용한 온칩 종단(ODT) 회로와, 480Mbps 데이터 송신을 위한 전류모드 차동 출력 구동회로를 설계하였다. 또한, 플레시오크로너스 클럭킹 방식을 사용하는 USB 시스템에서, 송수신단 사이의 주파수 차이를 보상하기 위하여, 클럭데이터 복원회로와 FIFO를 사용한 동기화 회로를 설계하였다. 네트웍 분석기를 이용한 손실전송선(W-model) 모델 파라미터를 측정을 통해 추출하였으며, 설계를 위한 시뮬레이션 과정에 활용하였다. 설계된 칩은 0.25um CMOS 공정으로 제작하였으며, 이에 대한 측정 결과를 제시하였다. IO패드를 제외한 칩의 코어 면적은 $0.91{\times}1.82mm^2$ 이었고, 2.5V 전원전압에서 전체 전력소모량은, 480MHz 동작 시 245mW, 12MHz 동작 시 150mW로 시뮬레이션 되었다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.961-965
• /
• 1998

The rapid development of small-scale (1-10 MJ) Superconducting Magnetic Energy Storage Systems (SMES) can be explained by real perspective of practical implementation of these devices in electro power nets. However the serious problem of all high mechanically stressed superconducting coils-problem of training and degradation (decreasing) of operating current still exists. Moreover for SMES systems this problems is more dangerous because of pulsed origin of mechanical stresses-one of the major sources of local heat disturbances in superconducting coils. We investigated acoustic emission (AE) phenomenon on model and 0.5 MJ SMES coils taking into account close correlation of AE and local heat disturbances. Two-coils 0.5 MJ SMES system was developed, manufactured and tested at Russian Research Center in the frames of cooperation with Korean Electrical Engineering Company (KEPCO) [1]. The two-coil SMES operates with the stored energy transmitted between coils in the course of a single cycle with 2 seconds energy transfer time. Maximum operating current 1.55 kA corresponds to 0.5 MF in each coil. The Nb-Ti-based conductor was designed and used for SMES manufacturing. It represents transposed cable made of Nb-Ti strands in copper matrix, several cooper strands and several stainless steel strands. The coils are wound onto fiberglass cylindrical bobbins. To make AE event information more useful a real time instrumentation system was used. Two main measured and computer processed AE parameters were considered: the energy of AE events (E) and the accumulated energy of AE events (E ). Influence of current value in 0.5 MJ coils on E and E was studied. The sensors were installed onto the bobbin and the external surface of magnets. Three levels of initial current were examined: 600A, 1000A, 2450 A. An extraordinary strong dependence of the current level on E and E was observed. The specific features of AE from model coils, operated in sinusoidal vibration current changing mode were investigated. Three current frequency modes were examined: 0.012 Hz, 0.03 Hz and 0.12 Hz. In all modes maximum amplitude 1200 A was realized.

• Progress in Superconductivity
• /
• 제13권1호
• /
• pp.24-27
• /
• 2011

High voltage insulation in cryogenic environment is one of big issues for development of superconducting power application, such as superconducting fault current limiter, transformer, transmission cable, and so on. We had proposed a composite solid insulator composed of plastics and polymer insulation sheets for a use of high voltage superconducting power applications. It is well known that the G10 FRP keeps its mechanical strength at very low temperature and the PPLP is very good insulator adopted as insulations for superconducting transmission cables. The composition of these two materials will show very good electrical and mechanical properties adequate for the insulation components of superconducting power applications, such as bushing, insulation barrier, and even for a cryostat. Dielectric strengths of prepared samples were measured at the temperature of boiling point of liquid nitrogen at atmospheric pressure, which will be presented in this paper to show a usefulness of this technique.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.243-244
• /
• 2006

As an preliminary study for the quench protection of high temperature superconducting (HTS) cable using superconducting fault current limiter (SFCL), experimental research was carried out. The test circuit was composed of Bi-2223/Ag HTS tape and a SFCL made of YBCO thin films. In the normal state, the applied current of 56 A, which was critical current of HTS tape, could be flown through the circuit without resistive loss. Increasing the currents, the quench development of both materials was investigated from the voltage signal acquired from the resistance of the quenched superconductor. Up to around 10 times of the critical current was applied to the HTS tape and the current limiting characteristics of SFCL were investigated. In addition, for the finding out the optimal operating condition of SFCL such as the numbers of elements, a shunt resistor was applied to the SFCL and quench characteristics were analyzed as well.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권6호
• /
• pp.416-428
• /
• 1999

A user-interactive pixel design tool for high-quality TFT-LCDs is realized and used to explore the sensitivity of the various array and device parameters for optimizing pixel design. In this tool, the Thompson cable equation and gradual-channel approximation were used for the gate time delay and TFT current modeling respectively. With this tool, each capacitance element, and TFT and array dimensions can be optimized under given design specifications. The electrical characteristics such ascharging ratio, gate time delay, pixel voltage level-shift, and holding ratio can be analyzed. The sensitivity analysis of those design parameters were executed and presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.699-700
• /
• 2006

고온 초전도 전력케이블의 통전용량 산정은 먼저 고온 초전도 전력케이블의 임계전류를 먼저 알아야 한다. 선재의 임계전류를 알고자 하는 경우, 전압-전류를 측정하거나 온도를 측정하는 방법을 통해 임계전류를 알아내지만, 고온 초전도 전력케이블의 경우 이러한 방법으로 임계전류를 알아내는 것이 불가능하다. 본 논문에서는 고온 초전도 케이블에 사용되는 선재에 대한 임계전류를 측정하고, 전자장 해석을 한 후, 실험결과와 해석 결과를 토대로 고온 초전도 전력케이블의 임계전류를 계산하였다. 이렇게 계산된 임계전류를 이용하여 고온 초전도 전력케이블의 통전용량의 기초자료로 활용토록 하였다.

• 전자통신동향분석
• /
• 제8권4호
• /
• pp.143-156
• /
• 1993

ISDN 을 구축하기 위한 망구조로 ISDN 의 다양한 서비스 수용 관점에서 Single Star 형 망구조가 가장 잠재력이 우수한 구조로 평가되고 있으며 Single Star 형 구조로 구축될 때 High Count Optical Fiber Cable 과 광커넥터 (단심, 다심) 가 요구된다. 그중 광커넥터는 광 가입자 망의 구축을 위해 필수적인 부품으로서 기술 추세는 다심화, 복합 기능화, 소형화, 저가격화, 고성능화, 고신뢰성화의 방향으로 진행되고 있다. 본 고에서는 향후 국내에서 적용 가능한 광케이블용 다심 광커넥터 개발을 위하여 외국에서 개발되어 있는 제품의 정렬원리, 정렬 구조 및 제조기술을 분석하였으며 또한 국내의 수요를 분석하였다. 수요 분석은 과거의 생산 실적 자료가 없는 이유로 정량적 분석법보다는 전화 가입자 수요 자료와 가입자 선로의 광케이블 계획, 그리고 광 CATV 가입자 예측 자료를 이용한 정성적인 방법을 적용하였다.

• 한국조명전기설비학회지:조명전기설비
• /
• 제6권6호
• /
• pp.23-31
• /
• 1992

Charged particle in the polymers is supposed to affect the electrical conduction and to lead them th dielectrical breakdown finally. So we measured the space charge distribution made by application of high electric field and evaluated the polarity of the charged particle affected on electrical conduction and space charge formed in the insulating materials by using temperature gradient thermally stimulated current measurement method(TG-TSC measurement). As a result, in the cross-linked polyethylene, A-peak was caused from dipole polarization, C-peak was caused from ionic space charge polarization and D-peak was injected trap hole. Also we found it crossible the evaluated the polarity of injected trap carrier and electron(or hole) of carrier trap in the cross-lined polyethylene. We found that ${\gamma}$-ray irradiated low density polyethylene had a relation to the electronic trap and we also could get the value of electric field distribution in the samples of which evaluation was available.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 A
• /
• pp.304-306
• /
• 2004

Recently, operating equipment with the high quality is necessary as technology is developing rapidly and equipment becomes more accurate. Therefore, the importance of diagnosis has been rising in modem industries. This paper presents that the induction motor is driven by invertor. We were using EMTP (Electromagnetic Transient Program) to study different characteristics of induction motor caused by faults; single phasing and the short circuit fault. After having the fault occurred in feeder cable, motor current, flux and torque waveform are analyzed