• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.837-842
• /
• 2000

In the coiling process of helical steam generator tubes of integral reactor SMART, a considerable amount of spring back, which induces dimensional inaccuracy and difficulty in fabrication, has been arised. In this research, an analytical model was derived to evaluate the amount of the spring back for steam generator tubes. The model was developed on the basis of beam theory and elastic-perfectly plastic material property. This model was extended to consider the effect of plastic hardening and the effect of the tensile force on the spring back phenomena. Parametric studies were performed for various design variables of steam generator tubes in order to minimize the spring back in the design stage. A sensitivity analysis has shown that the low yield strength, the high elastic modulus, the small helix diameter, and the large tube diameter result in a small amount of the spring back. The amount of the spring back can be controlled by the selection of adequate design values in the basic design stage and reduced to an allowable limit by the application of the tensile force to the tube during the coiling process.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.977-983
• /
• 2003

Free vibration analysis of helical springs was performed by the use of the commercial finite element analysis program, ANSYS. The investigation of national frequency was focused on the effect of various parameters such as boundary conditions, spring indices, number of coil turns and helix angles which are considered to affect the free vibration of a spring. The finite element method was validated by comparison with the result of a previouosly published literature. The similarity of frequency trend was shown among three boundary conditions: clamped-clamped, free-free, simpliy supported-simply supported but there was no similarity in light of mode shapes among them. Several modes showed similar frequencies on and near the frequencies identified by the natural frequency formula of Wahl. Natural frequencies increased with spring indices and number of turns decreasing and with helix angles increasing. The results investigated by finiete element method were compared with the experemental result and theoretical result and showed a good agreement among them.

• 소성∙가공
• /
• 제8권4호
• /
• pp.384-392
• /
• 1999

In metal forming, there are problems with recurrent geometric characteristics without explicitly prescibed boundary conditions. In such problems, so-called recurrent boundary conditions must be introduced. In this paper, as a practical application of the proposed method, the precision cold forging of a helical gear has been simulated by a three-dimensional rigid-plastic finite element method and compared with the experiment. The application of recurrent boundary conditions to helical gear forging analysis is proved to be effective and valid. the elastic stress analysis of the die for helical gear forging has been calculated by using the nodal force at the final stage obtained from the rigid-plastic finite element analysis. In order to obtain more precise gear products, the elastic analysis of the die after release of punch and the elastic spring-back analysis of product after ejection have been performed, and the final dimension of the computational product has been in good agreement with that of the experimental product.

• 한국음향학회지
• /
• 제25권6호
• /
• pp.282-290
• /
• 2006

본 논문에서는 1.2 kbps 의 전송률을 가지는 초 저속 음성 부호화기를 위한 방법과 구조를 제안한다. ZFE-CELP (Zinc Function Excitation-Code Excited Linear Prediction) 음성 부호화기는 선형예측 분석 후, 추출된 잔여 신호가 유성음일 경우 Zinc Function을 이용하여 부호화하고, 무성음일 경우에는 CELP 구조를 이용하여 부호화한다. 또한 Super-frame (40ms) 의 영향으로 발생하는 하모닉의 불연속 문제를 해결하기 위해 오버 샘플링을 이용한 선형 위상 합성 기법을 이용하고 Zinc 함수의 정확한 표준파형을 추출하기 위하여 분석-합성 구조를 제안한다. 제안된 초 저속음성 부호화기의 성능을 2.4 kbps의 MELP (Multi Pulse Linear Prediction) 부호화기 및 1.9kbps의 ZFE-PWI (Zinc Function Excitation-Prototype Waveform Interpolation) 음성 부호화기와 비교하였다 제안된 부호화 방법은 19kbps ZFE-PWI 부호화기와 유사한 성능을 보이는 것을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.237-240
• /
• 1999

The elastic stress analysis of the die for helical gear forging has been calculated by using the nodal force at the final stage obtained from the rigid-plastic finite element analysis. In order to obtain more precise gear products. the elastic analysis of the die after release of punch and the elastic spring-back analysis of product after ejection have been performed and the final dimension of the computational product has been in good agreement with that of the experimental product.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.355-360
• /
• 2001

By using Frenet formulation and Timoshenko beam theory, the partial differential equations of motion are derived for a helical spring having a doubly symmetrical cross section subjected to the pre-load axially. These equations of motion are solved to give the dispersion relationship and dynamic stiffness matrix is assembled. Natural frequencies are obtained from the receptance of the system. The results of the dynamic stiffness method are compared with those of the transfer matrix method from published examples and finite element method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1042-1048
• /
• 2007

This work analytically investigated the radiated noise of a helical gear-housing system due to the excitation of helical gears. The helical gears were modeled as a 12-degree of freedom mass-spring-damper system; the shaft was modeled as a rod, a beam, and a torsional shaft; and the gear housing was modeled as a clamped circular plate with viscous damping. The modeling of this system used transfer matrices for helical gears, shafts, and bearings. Damping for both the bearings and the plate were obtained by modal testing. For the evaluation of noise, sound pressure from the plate due to the force and the moment in both radial and tangential directions was analytically derived by the Rayleigh integral. The analytical derivation and parameters from the experiment were applied to an analysis of noise for the two sets of helical gears with differing gear ratios. The analysis showed that the moment excitation in both helical gears contributed more to the noise of the plate than axial force excitation.

• Structural Engineering and Mechanics
• /
• 제28권6호
• /
• pp.659-676
• /
• 2008

The reports regarding the free vibration analysis of uniform beams carrying single or multiple spring-mass systems are plenty, however, among which, those with inertia effect of the helical spring(s) considered are limited. In this paper, by taking the mass of the helical spring into consideration, the stiffness and mass matrices of a spring-mass system and an equivalent mass that may be used to replace the effect of a spring-mass system are derived. By means of the last element stiffness and mass matrices, the natural frequencies and mode shapes for a uniform cantilever beam carrying any number of springmass systems (or loaded beam) are determined using the conventional finite element method (FEM). Similarly, by means of the last equivalent mass, the natural frequencies and mode shapes of the same loaded beam are also determined using the presented equivalent mass method (EMM), where the cantilever beam elastically mounted by a number of lumped masses is replaced by the same beam rigidly attached by the same number of equivalent masses. Good agreement between the numerical results of FEM and those of EMM and/or those of the existing literature confirms the reliability of the presented approaches.

• 대한치과교정학회지
• /
• 제21권2호
• /
• pp.353-366
• /
• 1991

This study was performed to analyze the effects of forces to the alveolar bone by various molar uprighting spring such as helical uprighting spring. T-loop spring, Modified T-loop spring and open coil spring. The simplified two-dimensional photoelastic model was constructed with a lower left posterior quadrant containing the second molar, the first and second premolars and the canine, with the first molar missing. Several molar uprighting springs were fabricated from 0.017 by 0.022 inch blue Elgiloy and applied to the photoelastic model. Two-dimensional photoelastic stress analysis was performed, and the stress distribution was recorded by photography The results obtained were as follows; 1. In all the kinds of the springs, the center of rotation of the mandibular second molar was oserved at the apical 1/5-1/6 between the alveolar crest and the root apex. 2. In all the kinds of the spring, the stress induced in the mesial root surface of the mandibular second molar was relatively homogeneous but there was some difference in the magnitude of the stress. 3. In the kinds of the springs, the distal crown tipping moment of the second molar was increased in turn as open coil spring, helical uprighting spring, T-loop spring, and modified T-loop spring. 4. The largest extrusive force was occured in the T-loop spring, intrusive force was occured in Modified T-loop spring only, and the largest distal tipping force was occured in open coil spring. 5. In the T-loop spring with activation, the stress induced in the mesial root surface of the second molar was increased gradually from the root apex to the alveolar crest and highly concentrated in the alveolar crest.

• 대한기계학회논문집A
• /
• 제40권2호
• /
• pp.237-244
• /
• 2016

산업에서 널리 사용되고 있는 압축 원통 코일 스프링은 제작 시 스프링 고유의 특성을 유지할 수 있는지 실험을 통해 검증해야 한다. 이 과정에서 많은 시간과 비용을 소비한다. 따라서 본 연구에서는 선형 정적 구조 해석 방법을 이용하여 스프링의 구조 건전성 평가를 수행하였다. 본 연구의 타당성을 입증할 목적으로 설계 규격 및 각종 국제적 평가 규격에 의한 실험적 방법과의 비교 및 검증을 수행하였다. 양 끝단 처리를 하지 않은 스프링 형상을 사용하여 구조 해석을 수행한 결과, 해석 모형 제작에 필요한 시간은 절감하고 격자의 질은 향상할 수 있었다. 푸아송 비는 구조 해석 결과에 별다른 영향을 미치지 않았다. 그리고 구조 해석만으로 스프링 구조 건전성을 검증할 수 있는 가능성을 확인하였다.