• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.81-86
• /
• 1991

The iterative learning operation has been utilized in the temperature Control of a batch reactor. A generic form of feedback-assisted first-order learning control scheme was constructed and then various design and operation modes were derived through convergence and robustness analysis in the frequency domain. The proposed learning control scheme was then implemented on a bench scale batch reactor with the heat of reaction simulated by an electric heater. The results show a great improvement in the performance of control as the number of batch operations progressed.

• Proceedings of the SAREK Conference
• /
• 2003.07a
• /
• pp.119-119
• /
• 2003

• 한국전산유체공학회:학술대회논문집
• /
• 2003.08a
• /
• pp.194-199
• /
• 2003

The studying is to analyze characteristic of air flow and is used to design in an automotive HVAC module. The RNG k-e turbulence model with the Upwind Difference convection scheme and an unstructured hybrid mesh with arbitrary matching method were applied to the simulation. The comparing air flow characteristic of the basic HVAC module and total HVAC module with blower were discussed in the paper.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.23-30
• /
• 2016

In this study, the heat transfer and pressure drop characteristics were evaluated for multi-tube $CO_2$ water heaters with lengths of 4.5 m and 7.5 m. The evaluation was done using the -NTU method, and the results were compared with experimental data. Water flows through the shell side of the water heater, while $CO_2$ flows through 8 inner tubes. The heater uses a counter-current design to maximize the heat transfer efficiency. The energy balance equation describing the flows of $CO_2$ and water for each node is set up using the section-by-section method. The calculated heat transfer rates agree well with the experimental data within ${\pm}5%$ error. The outlet water temperature decreased linearly with the increase of the water flow rate. The calculated heat transfer rates agreed well with the experimental data within ${\pm}3%$ error. The results show that the heat transfer rate increases almost linearly with the increase of water flow rate or $CO_2$ inlet temperature in both the 4.5-m and 7.5-m water heaters, whereas the water outlet temperature linearly decreases with the increase of the water flow rate. The comparison of the $CO_2$ pressure drop between the calculation and experiment results shows good agreement at the high $CO_2$ flow rate within 5 % error, but the value is about 20 % higher in the experimental pressure drop at the low $CO_2$ flow rate.

• Advanced Industrial SCIence
• /
• v.2 no.2
• /
• pp.9-15
• /
• 2023

Since silicone rubber heaters are flexible, they can be directly attached or installed in objects to be heated even in flat, curved or three-dimensional shapes. Since the current heating method heats the entire object to be heated and raises it to a required temperature, ignoring areas or positions where heat is not required, partial intensive heating cannot be performed. When using multi-heating zones, rather than heating the entire object to be heated, only the parts that need heat are intensively heated according to the process, so it is possible to heat quickly by local location by applying different amounts of heat with a small amount of electric capacity to each place that needs heat, and heat energy can reduce. In this study, the temperature and heating time of the partially concentrated region in the multi-heating region structure are measured so that a uniform temperature or temperature difference occurs in the region requiring thermal fusion. In order to determine the optimal power density range and reduce capacitance, the safety of a silicon rubber heater manufactured with a multi-heating zone structure is investigated. If the silicon rubber heater is manufactured in a multi-heating method, the multi-intensive heating technology can be ideally applied to all heating processes.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.2
• /
• pp.252-257
• /
• 2005

In this work, we propose a simple but efficient method to design a target temperature trajectory for pulling speed tracking control of the crystal grower in the Czochralski crystallization process. In the suggested method, the model predictive control strategy is used to incorporate the complex dynamic effect of the heater temperature on the pulling speed into the temperature trajectory design quantitatively. The feedforward trajectories designed by the proposed method were implemented on 200 mm and 300 mm silicon crystal growers in the commercial Czochralski process. The application results have demonstrated its excellent and consistent tracking performance of pulling speed along whole bulk crystal growth.

• Nuclear Engineering and Technology
• /
• v.29 no.2
• /
• pp.148-157
• /
• 1997

A new capsule that has a unique structure in which the test environments including neutron flux and fluence, and irradiation temperature can be controlled precisely during irradiation, was conceptually designed. The capsule structure and instrumentation were successfully designed according to the JMTR's standard procedures of capsule design. Based on the target irradiation, the details of the irradiation such as neutron fluence and irradiation temperature ore calculated and the related capsule safety was evaluated. In addition, the effects of design parameters including the changes in inner-capsule configuration, heater capacity, and Helium gas pressure on the specimen temperature were analyzed with a computer program. Through these thermal and strength evaluations, this capsule was proved to be safe during the irradiation in the JMTR.

• Journal of Applied Tourism Food and Beverage Management and Research
• /
• v.16 no.2
• /
• pp.121-133
• /
• 2005

We live seeing, touching, or throwing on considerable textile in our life consciously and unconsciously. Since a Korean-style house is a dwelling space in life style of sitting on the floor with ondol(Korean floor heater), use of textile is limited to bedding goods. However, as western life style takes firm root, use of textile for interior design is increasing. As well, as apartments and foreign style houses have gotten lodgment since 1980, life style is being changed rapidly. So, textile became required factors in dining space where little textile existed. Through literature, history of textile is considered and design image concept is created based on the consideration. In addition, the created concept can be applied to various textile design, which can be a good tool to express eating culture of the country as well as the country's image.

• Carbon letters
• /
• v.25
• /
• pp.25-32
• /
• 2018

In this study, a thermal-gradient chemical vapor infiltration (TG-CVI) process was numerically studied in order to enhance the deposition uniformity within the preform. The computational fluid dynamics technique was used to solve the governing equations for heat transfer and gas flow during the TG-CVI process for two- and three-dimensional (2-D and 3-D) models. The temperature profiles in the 2-D and 3-D models showed good agreement with each other and with the experimental results. The densification process was investigated in a 2-D axisymmetric model. Computation results showed the distribution of the SiC deposition rate within the preform. The results also showed that using two-zone heater gave better deposition uniformity.

• Proceedings of the Korea Hospitality Industry Research Society Conference
• /
• 2005.11a
• /
• pp.123-133
• /
• 2005

We live seeing, touching, or throwing on considerable textile in our life consciously and unconsciously. Since a Korean-style house is a dwelling space in life style of sitting on the floor with ondol(Korean floor heater), use of textile is limited to bedding goods. However, as western life style takes firm root, use of textile for interior design is increasing. As well, as apartments and foreign style houses have gotten lodgment since 1980, life style is being changed rapidly. So, textile became required factors in dining space where little textile existed. Through literature, history of textile is considered and design image concept is created based on the consideration. In addition, the created concept can be applied to various textile design, which can be a good tool to express eating culture of the country as well as the country's image.