• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.17-23
• /
• 2001

AKD sizing behavior of handsheets, which were prepared from the different pulps with various AKD fixing agents, was studied in this investigation. AKD sizing performance could be improved by removal of fines in the stock, minimizing damage of fiber, using a suitable fixing agent and heat treatment. Fillers with low surface energy, like calcium carbonate and talc, showed quite positive effect in AKD sizing. When PAM was added to the DIP stock as fixing agent, it showed lower sizing degree than polyamine did. But in case of NBKP system, PAM was more effective than polymine.

• Journal of Energy Engineering
• /
• v.8 no.1
• /
• pp.76-84
• /
• 1999

The demand of Small Self-generating System (SSS) including Small Cogeneration System (SCS) is constantly increasing with the need of electricity and/or thermal in office, hospital, hotel, and small factory, etc. It is especially recommended to operate SCS in the heat-following mode to maximize the efficiency of generator. In case of the heat-following mode SCS has got to be connected to distribution system so as to send surplus power to the utility or receive the short power from utility. But the interconnection of SSS with distribution system causes a few problems such as the bad power quality, and low security. If SSS is not promptly disconnected after faults occur (Islanding of SSS), it can not only damage equipment of utility and adjacent customers but also endanger life of human due to overvoltage or overcurrent. In this paper it has been deeply discussed if interconnection of engine self-generator/control system satisfies the protective requirement for SSS or not. 500 kW engine generator running in the Jodo island has been used to perform the analysis of interconnection.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.234-234
• /
• 2003

Indium tin oxide(ITO) is an advanced ceramic material with many electronic and optical applications due to its high electrical conductivity and transparency to light ITO thin films are used in transparent electrodes for display devices, transparent coatings for solar energy heat mirrors and windows films in n-p heterojunction solar cells, etc. Almost all display devices were fabricated on transparent ITO electrode substrates. There are several factors that cause decay in the efficiency and the failure of display devices. The degradation or damage of ITO is one of the main factors. Under normal operating conditions, the electric fold required for the operation of display devices is very high As a high electric field induces the joule heat, the degradation of the ITO thin film may be expected. Therefore, it is worthy to investigate the thermal and electrical effect on ITO thin films.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.3
• /
• pp.69-76
• /
• 2015

The purpose of this paper is to find an limitation to detect the defect of damaged asphalt pavement structures for infrared thermography. We use heat source of a natural light to detect the defect efficiently. The heat source was applied to the asphalt specimens. Four asphalt specimens were used: one was the asphalt containing depth of 1cm internal timber, two was the asphalt containing depth of 2cm internal void, Three was the asphalt containing depth of 3cm internal timber and four was not the asphalt containing internal timber. It was found that the depth of 3cm internal timber could be detected by this method. In addition, we used the image processing to make the damage zone displayed clear in the image obtained from the thermographic operation.

• Architectural research
• /
• v.10 no.1
• /
• pp.1-11
• /
• 2008

A Steel column with damaged spray-applied fire resistive material (SFRM) may exhibit reduced structural performance due to the effects of elevated temperature during fire events. Thus, the fire load behavior of steel columns with removed or reduced SFRM needs to be examined to predict the structural damage by fire. FEM analyses were performed for the flange thinning removal models in which the SFRM was reduced as a constant strip in thickness at the top flange of the column. The temperature results for all models obtained from the heat transfer analyses were included as an initial condition in the FEM structural analyses. In this study, the results of analysis show that even small remnants of SFRM led to an effective reduction of temperature at any given fire duration, and improved significantly the axial load capacity of a column as compared to the complete removal cases of SFRM.

• Korean Journal of Oriental Medicine
• /
• v.13 no.1 s.19
• /
• pp.37-42
• /
• 2007

As the cholera was spread over the Joseon dynasty at 1821, Hwang Doyeon investigated the symptoms like diarrhea, vomiting, muscle cramp and so on, and he presented the cause of cholera as the damage of Primordial-gi caused by abnormal climate and Damp-heat made by taking inadequate foods. He regarded as of great importance the ordinary health condition by guessing the prognosis of the disease, and proposed how to make a diagnosis of dehydration by observing nails and toenails. To treat cholera, he presented the methods of Sipseon-bloodletting and Singwol-moxacautery, and mentioned compound herb remedies and single herbs like garlic etc. He wrote down Mulberry leaves and Argyi wormwood leaves as the preventor of cholera to emphasize the importance of prevention, and mentioned food contraindication in addition to keep from getting worse.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.914-917
• /
• 2001

Single-shot laser damage of thin Cr films on glass substrates has been studied to understand the cracking and peeling-off mechanism. A numerical model is developed for the calculation of transient heat transfer and thermal stresses in Cr films during excimer laser irradiation and cooling, the transient temperature, and the stress-strain fields are analyzed by using a three-dimensional finite-element model of heat flow. According to the numerical analysis for the experimentally determined cracking and peeling-off conditions, cracking is found to be the result of the tensile brittle fracture due to the excessive thermal stresses formed during the cooling process, while peeling-off is found to be the combined result of films bulging from the softened glass surface at higher temperature and the tensile brittle fracture during the cooling process.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.641-644
• /
• 2006

Considering properties of the low-heat concrete mixed with the blended cements, the influences compared blended cements with ordinary portland cement made experiments on. (1) Blended cements were superior to OPC in the fresh concrete flow that the use of blended cements reduced chemical admixture. (2) The more the use of additive increase, the more bleeding happens. So it is considered to heights, order, and rate of placement, curing methods and so on. (3) The use of blended cements increase long term strength after 28 days, but decrease early strength and durability. So it is considered to the curing methods and early frost damage, and endurance limit.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.899-902
• /
• 1997

The heat generated during surface grinding process can lead to elevate a grinding temperature, which cause the thermal damage to the workpiece material. Because of this reason, it is important to be able to predict the temperature which is occurred during grinding. The process parameters, therefore, should be adjusted properly to yield the acceptable workpiece temperature. In this study, we conducted an experimentation to obtain and also to analyze the temperature distribution of the workpiece with accordance in varying the grinding condition. For measuring the workpiece temperature, thermocouples of the CA type were inserted into the predetermined locations of the workpiece.

• Journal of the Korean Society for Railway
• /
• v.7 no.2
• /
• pp.142-148
• /
• 2004

When material properties depend much on positions in a material or it is difficult to make test specimens from a material or component, an instrumented indentation test described in ISO 14577-1, 14577-2 or KS B 0950 can be used to measure material properties and damage. In this study, first of all, the principals of the instrumented indentation test, KS B 0950 are introduced and yield strengths, tensile strengths and work hardening exponents of base materials, heat affected zones and weld materials are measured. In addition, the influence of post-weld heat treatment on the material properties is investigated. Finally the fatigue lift of butt welded specimens are evaluated by the local strain approach. To calculate local strains and stresses, elasto-plastic finite element analysis is conducted using the measured properties.