• Microbiology and Biotechnology Letters
• /
• v.37 no.4
• /
• pp.340-349
• /
• 2009

A CJ9 bacterial strain, which showed antifungal and antibacterial activities, was isolated from meju and identified as Bacillus polyfermenticus based on Gram staining, biochemical properties, as well as its 16S rRNA sequence. B. polyfermenticus CJ9 showed the antimicrobial activity against the various pathogenic molds, yeasts, and bacteria. The antibacterial activity was stable in the pH 5.0~9.0, but the activity was lost at $37^{\circ}C$ for 24 hr. The antifungal activity was stable in the pH range of 3.0~9.0 and reduced at $121^{\circ}C$ for 15 min, but antifungal activity was not completely destroyed. The antibacterial activity was completely inactivated by proteinase K, protease, trypsin, and $\alpha$-chymotrypsin. The antifungal activity was also completely inactivated by protease and $\alpha$-chymotrypsin, and reduced its activity by proteinase which indicated that the antifungal and antibacterial compounds have proteineous nature. The apparent molecular mass of the partially purified antifungal compound, as indicated by using the direct detection method in Tricine-SDS-PAGE, was approximately 1.4 kDa. The molecular mass of the antibacterial compound could not be determined because of its heat-liable characteristic.

• Microbiology and Biotechnology Letters
• /
• v.30 no.2
• /
• pp.135-141
• /
• 2002

This study was carried out to isolate antagonistic bacterium against Sclerotium cepivorum causing Allium fistulosum white rot. Total of 146 strains were isolated from A. fistulosum roots. The isolates were screened for antagonism to S. cepivorum and the isolated strain No. AL-1 was selected among these bacteria. It was identified as Serratia plymuthica based on morphological and physiological characteristics according to the Bergey's mannual of systematic bacteriology and 16S rDNA sequences methods. Serratia plymuthica AL-1 showed broad spectrum of antifungal activities against plant pathogenic fungi Alternaria altrata, Colletotrichum gleosporioids, Phoma sp., Rhizoctonia solani, Sclerotinia sclerotiorum, Stemphylium solani, Fusarium oxysporium niveum but not inhibited Didymella bryoniae. When S. plymuthica AL-1 cultivated in the TSB medium containing 1％ colloidal chitin, the high molecular fraction (>10 kDa) have chitinase activity (3.2 units/ml) and the low molecular fraction (<10 kDa) have not chitinase activity. Oppositely, after heat treatment (80℃ for 30 min) of the cultivation supernatant, the high molecular fractions have not antifungal activity but the low molecular fractions have antifungal activity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.107-114
• /
• 2017

A turbocharger is an engine supercharger that is driven by exhaust gas. It improves the output and fuel efficiency by increasing the charging efficiency of the mixture gas, which is achieved by changing the rotatory power of the turbine connected to the exhaust passage. It is important to control the supercharging for this purpose. A nozzle slide joint is one of the core parts. Austenitic stainless steel is currently used as the material for this part, and its excellent mechanical properties include high heat resistance and corrosion resistance. However, because of its poor machinability, there are many difficulties in producing products with complicated shapes. Machining is used in the production of nozzle slide joints for high dimensional accuracy after metal powder injection molding. As design variables in this study, we investigated the sintering temperature, product stress, deformation rate, radius of curvature of the punch, and angle of the chamfer punch, which are related to the strain and shapes. The goal is to suggest a forming process using Nitronic 60 that does not require machining to manufacture a nozzle slide joint for a turbocharger. Accordingly, we determined the best process environment using finite-element analysis, the signal-noise ratio, and the Taguchi method for experiment design. The relative density and hydrostatic pressure of the final product were in accordance with the results of the finite element analysis. Therefore, we conclude that the Taguchi method can be applied to the design process of metal powder injection molding.

• Microbiology and Biotechnology Letters
• /
• v.35 no.4
• /
• pp.339-346
• /
• 2007

The MJP1 bacterial strain, which possesses antifungal activity, was isolated from meju and identified as Bacillus subtilis based on its morphological and biochemical properties, as well as its 16S rRNA sequence. Antimicrobial activity was found against various species of Gram-positive bacteria, yeasts, and molds, including food-spoilage microorganisms. The antifungal activity was found to be stable after heat and proteolytic enzyme treatment, and in the pH range of $6.0{\sim}10.0$. The antibacterial activity was stable in the pH range of $6.0{\sim}10.0$, but about 50% of the activity was lost after 24 hr at $30^{\circ}C$. The antibacterial compound was also inactivated by proteolytic enzyme treatment, indicating its proteinaceous nature. The apparent molecular masses of the partially purified antifungal and antibacterial compounds, as indicated by using the direct detection method in Tricine-SDS-PAGE, were approximately 2.4 kDa and 4.5 kDa, respectively. These studies suggest that B. subtilis MJP1 produces two bacteriocin-like substances with antifungal and antibacterial activities.

• Microbiology and Biotechnology Letters
• /
• v.35 no.4
• /
• pp.304-309
• /
• 2007

Soybean is useful source of protein, especially in Asia. But soybean needs heat inactivation or fermentation process before consumption, since it contains the toxic lectin and various protease inhibitors. Therefore, production of soybean boiling-waste liquor (SBWL) as a byproduct is inevitable. In this study, the chemical composition of SBWL and the optimization of culture conditions for Bacillus pumilus JB-1, a selected strain for functional chungkuk-jang fermentation, using SBWL were investigated. The SBWL contains 88% water, 9.5% free sugar, 1.6% crude protein, 0.3% crude fat, 0.1% crude fiber and 2.1% ash, respectively. The contents of total polyphenol, total flavonoids and free amino acid in SBWL were 55%, 76%, and 30% of those of raw soybean, respectively. Culture conditions for B. pumilus JB-1 in SBWL were optimized. The 1/10-diluted, 0.1 % of $(NH_4)_2SO_4$ added SBWL without pH adjustment and carbon source addition was cultured at $37^{\circ}C$ for 48 h with agitation (120 rpm). The 0.5% of inoculation was enough. The large scale fermentation in 5-L jar fermentor showed that the SBWL is a good resource for production of chungkuk-jang starter and functional ingredients.

• The Journal of Korean Academy of Prosthodontics
• /
• v.36 no.6
• /
• pp.858-866
• /
• 1998

Soldering is the usual method used to correct an unstable fixed partial denture framework at patient's try-in; However, presoldering base metal alloys is technique-sensitve and results are unstable because it is difficult to maintain uniform heat distribution and to prevent oxidation of an alloy. A cast-joining technique has been developed by Weiss and Munyon for repair, correction and addition to base metal framework. This joining technique eliminates the problem with presoldering of non-precious frameworks. The object of this study was to 1) compare the relative flexure strength and the joining effectiveness of Ni-Cr-Be cast in two pieces and 'pre-soldered' versus in two pieces and 'cast-joined'. 2) determine the effect of increasing the number of retentive grooves on the face of the cast and 3) determine the effect of the relative matched position of groove patterns on flexure strength. The joining effectiveness can be expressed by the ratio of the mean flexure stress of soldered or cast-joined specimens to that of one-piece cast. Resin rods 3mm in diameter were used as pattern of specimens for one-piece casted, presoldered, and cast-joined groups. Cast-joined specimens had two different patterns of retentive grooves on the joined faces. Type A had cross-shaped grooves 1mm in depth. 0.6mm in width. Type B was the same except for the addition of one more retentive groove. In the experiment connecting cast-joined specimens, half of specimens with type A pattern had their patterns on the faces of paired casts matched with each other as mirror image. With the rest pairs, it was proceeded that one of paired casts turned 45 degrees so that the patterns crossed. Half of specimens with type B pattern also had the patterns matched as mirror image; However, here, one of paired casts turned 90 degrees with the other pairs. Retentive groove in this study lacked the intentional undercuts, in contrast with the suggestion of Weiss and Munyon. The specimens were subjected to four-point flexural loading in an Instron testing machine. The midspan flexural stress was calculated at the point of initial plastic strain as determined from a strip-chart recorder or at the point of failure if this occured at a lower stress level. Within the scope of this study, the following results were obtained. 1. The presoldered group showed flexural strength at least 2 times higher than the cast-joined groups. Its joining effectiveness was 82%. 2. In cast-joined groups, the flexural strength of joints with type B patterns exhibited 1.5 times that of joints with type A patterns. Joining effectivenesses were 38% for type B patterns, 25-26% for type A patterns. 3. The relative matched position of groove patterns did not have any significant effect on flexural strength of the cast-joined specimens with either type A patterns or type B patterns(p>.05).

• Journal of Life Science
• /
• v.28 no.1
• /
• pp.68-77
• /
• 2018

The purpose of this study was to isolate the probiotic lactic acid bacteria, and verify the possibility of the final selection strain as probiotic material. For screening of biogenic amines non-producing microorganisms, 42 lactic acid bacteria were isolated from various berries, extract and vinegar grown in Sunchang. Isolates were investigated for various physiological activities such as extracellular enzyme, antimicrobial and antioxidant activities, and 5 isolates were firstly screened. SBB07 was finally selected by analyzing the biogenic amine, and named Lactobacillus brevis SBB07 by 16S rRNA sequencing analysis. Next, SBB07 was assayed for their survival ability when exposed to acidic and bile conditions as well as heat and antibiotic resistance. As a result, SBB07 showed more than 86% and 54% higher survival rate in acidic condition at pH 2.0 and bile resistance with 0.5% oxgall. In addition, SBB07 showed a survival rate of more than 113% in $60^{\circ}C$, and also confirmed that it has resistant to various antibiotics. As a result of confirming the possibility of prebiotics, SBB07 showed the best utilization of GOS as a prebiotic substrate, and utilization of FOS and inulin were also high. These results suggest that SBB07 have good potential for application as probiotic lactic acid bacteria.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.221-228
• /
• 2004

Basic properties of artificial lightweight aggregate by using waste dusts and strength properties of LWA concrete were studied. Bulk specific gravity and water absorption of artificial lightweight aggregates varied from 1.4 to 1.7 and 13 to 16%, respectively. Crushing ratio of artificial lightweight aggregate was above 10% higher than that of crushed stone or gravel. As a result of TCLP leaching test, the leaching amount of tested heavy metal element was below the leaching standard of hazardous material. Slump, compressive strength and stress-strain properties of LWA concrete made of artificial lightweight aggregate were tested. Concrete samples derived from LWA substitution ratio of 30 vol% and W/C ratio of 45 wt% showed the best properties overall. Thermal insulation and sound insulation characteristics of light weight concrete panel with the optimum concrete proportion were tested. Average overall heat transmission of 3.293W/㎡$^{\circ}C$ was observed. It was higher by about 15% than those of normal concrete made by crushed stone. Sound transmission loss of 50.9 ㏈ in frequency of 500 ㎐ was observed. It was higher by about 13% than standard transmission loss.

• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.2
• /
• pp.219-235
• /
• 1993

To determine the compatibilities of soft liming materials with denture cleansers by measuring the flexibility and elasticity and investigating the surface changes, 4 self-curing acrylic resin soft lining materials and 1 heat-curing silicone soft lining material were evaluated. 3mm thick x 20mm diameter discs of soft lining materials were individually bonded to a hard acrylic resin base as per manufacturers’instructions. Using an Instron universal testing machine, a static stress of $2kg/cm^2$ was applied for 30secs., the strain in compression was measured, giving an indication of the material’s flexibility. Elastic recovery was measured at 10secs. After removal of stress. Surface changes were investigated with Stereomicroscope. Then the specimens were immersed in 4alkaline peroxide denture cleansers and water as control group, tests were carried out at 1 day, 2 days, 7 days, 14 days and 30 days. The results were as follows : 1. Alkaline peroxide denture cleansers caused considerable porosity on the surface of selfcuring acrylic resin soft lining materials, and the most affected by the cleansers were Viscogel, Coe-Soft, Coe-Comfort, Lynal, in that order. 2. There was significant difference in flexibility between each soft lining material except for Coe-Comfort and Visco-gel, and every soft lining material was significant difference in elasticity. Especially Molloplast-B and Lynal were less flexible and more elastic than other soft lining materials(p<0.05). 3. The denture cleansers increased the flexibility and elasticity of the soft lining materials compared with control group(p<0.05), and Denalan, Polident, Kleenite, Efferdent affected the soft lining materials in that order. 4. There was significant difference in flexibility between each denture cleanser except for Denalan and Polident(p<0.05). Though Denalan and Polident, Denalan and Kleenite did not show significant difference in elasticity, other denture cleansers showed significant difference among each other(p<0.05). 5. Clinically Coe-Comfort, Coe-Soft and Visco-gel were incompatible with alkaline peroxide denture cleansers, and Lynal would be used within only 2 weeks. But Molloplast-B was compatible with alkaline peroxide denture cleansers.

• Korean Journal of Microbiology
• /
• v.17 no.4
• /
• pp.165-178
• /
• 1979

Phages of Lactobaciilus casei (PLC) isolated from plant drainage were classified and characterized. The results are as follows : 1. On the basis of host range pattern, phages could be divided into 2 groups (PLC-B and PLC-C). PLC-B group phages could be further divided into 5 sub-groups $(B_1, \;B_2, \;B_3, \;B_4, \;and\;B_5)$. Although PLC-C group phages had the same host range, they could be also divided into 2 sub-groups $(C_1\;and\;C_2)$ by morphlogical type. 2. It was $B_3$ group phages that represented a major proportion (44.4%) of phages tested. However, $B_1$ group phages were shown to have the widest host range. 3. Electron micrographs revealed that the phages fell into three different morphological types. $(B_1, \;B_2, \;and\;B_3)$ group phages hd a hexagonal head (52nm in diameter) and a sheathless noncontractile (245 nm in length). $B_4\;and\;C_2$ group phages had a hexagonal head (56 nm) and a short flexible tail (169nm) having no sheath. $B_5\;and\;C_1$ group phages were shown to have a hexagonal head (81 nm) and a contractile tail (140 nm) having a sheath, a base plate and tail fibers. 4. The inactivation of the phages by antisera indicated that serological relationships correlated completely with morphological types. 5. $B_1, \;C_1\;and\;C_2$ group phages produced a large (1, 2 mm in diameter) plaque with a clear ring. The morphology of plaques of $B_3\;and\;B_5$ group phages was the same as those produced by the above, but the average plaque sizes for $B_3\;and\;B_5$ were 0.8 mm abd 0.5 mm, respectively. $B_2\;and\;B_4$ group phages produced a small (0.5 mm) turbid plaque with an irregular edge. 6. The latent period and the average burst size of $B_1\;and\;B_3$ group phages were 90 min and 100, respectively. These phages reuqired calcium ions for their miltiplication. 7. $B_3$ group phages could not be absrobed to R-variant $KC_1$. 8. The order of resistance of phages to heat was $B_2\;>\;B_1, B_4\;and\;B_5\;>\;B_3\;and\;C_2, \;B_5$ group phages were more stable than $B_3$ in various pH values. $C_2$ group phages were more sensitive to UV irradiation than $B_1\;and\;B_3$ group phages. 9. Strains YIT9018 and IAM 1043 were induced by mitomycin C treatment. Phage particles detected in the lysates had a hexagonal head (38 and 49 nm, respectively), but no tail. Any sensitive indicator strain could not be isolated in spite of repaeated trials.