• Journal of the Korea Institute of Building Construction
• /
• v.4 no.1
• /
• pp.85-88
• /
• 2004

The purpose of this study was to design the self-compaction concrete mixture, having not only high strength but also compensation of shrinkage without thermal crack under 4 sides outer restraint of the member. In the experimental mix, replacement ratio of limestone Powder, CSA expansive additives, and unit water were selected as parameters, using portland blast-furnace slag cement. And, bleeding test, expansibility test. hydration heat analysis were performed. As a results, when 35% of limestone Powder, 6% CSA expansive additives are replaced at unit water 175kg/$\textrm{m}^3$, demanded performances of fresh and hardened self-compaction concrete are accomplished.

• Journal of the Korea Institute of Building Construction
• /
• v.7 no.4
• /
• pp.133-138
• /
• 2007

This research goes into the field application cases about Flat slab concrete divide placing construction for the Multi-purpose Apartment. It is important to investigate sufficiently when mass concrete is applied to the substituted divide placing and admixture(blast furnace slag and fly ash). In addition, it is improved on the concrete quality by the job mix design which can decrease cracks caused by the heat of hydration, by the good compactability and the substitution of admixture that can prevent segregation when concrete is poured, and by the good conditioned fluidity which makes the efficiency of building construction. After considering the stated above, the sufficient prior consideration is important for a quality Improvement plan at the field use concrete of the Mass Concrete when divide placing and admixture are substituted and applied.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.205-210
• /
• 1998

The strength and dimension of recent constructed subway box structures are increased considerably. These increases are resulting in much initial cracks by hydration heat and thermal stress. According to previous studies, decrease of cement amount by using superplasticizer and L/H value is the best way to eliminate hydration heat and stress. The analyses using finite element model were performed. By the result of analysis, the use of superplasticizer and the decrease of the change of longitudinal placing length are proved to be more effective for elimination thermal cracks. By ACI Code, for longitudinal placing length 25 m, the amount of wall temperature reinforcement is always lack despite of concrete mix proportion. With analytical result and the inducing crack joint, the in-site test were performed and the analytical results proved to be effective. However, the inducing crack joint is not effective if it is a small size.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.04a
• /
• pp.107-113
• /
• 1992

The heat of hydration of cement the causes the internal temperature rise at early age, particulary in massive concrete structures such as a mat-slab of nuclear reactor building or a dam or a large footing. As the result of the temperature rise and restraint of foundation, the thermal stress enough to induce concrete cracks can occur. Therefore, the prediction of the thermal stress is very important in the design and construction stages in order to control the cracks developed in massive concrete structures. And, more creep and shrinkage take place at elevated temperatures in young concrete, Thus the effect of creep and shrinkage must be considered for checking the safety and servicebility(crack, durability and leakage).

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.1229-1234
• /
• 2001

The bottom slab of Inchon LNG in-ground #213 tank is designed as a massive structure witch has a large depth and section. The purpose of this study is to determine the optimum mix design having good workability and low hydration heat for bottom slab concrete and to control the actual concrete quality in site. For this purpose, we select the optimum mix design used ternary blended cement(furnace slag cement＋fly ash) and design factors. As test results of actual application, we have finish placing the bottom slab concrete of 23,180㎥ during 68hours with good success and obtain the good quality of fresh and hardened concrete including slump, air contents, no-segregation, compressive strength and low hydration heat in actual data. All test results are satisfied with our specifications for bottom slab concrete and we cut costs as the use of ternary blended cement and the reduction of placing hours.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.195-200
• /
• 1995

This paper presents the practical use of high strength concrete on 28-story Samsung Shin-dacbang Housing-Commercial Combined Building with 8-story basements located in Seoul. 700 Kg/$\textrm{cm}^2$ compressive Strength concrete was placed for basement core-walls and 500 kg/$\textrm{cm}^2$ concrete was used for structural frames up to 10th floor. The thermal sensors were installed prior to concrete casting into the core walls to measure the heat of hydration during hardening process. The correlation of core strength to the standard cylinder test strength was also discussed. The successful utilization of 500 and 700 kg/$\textrm{cm}^2$ concrete shows that the practical application of high strength concrete has a great potential to the high-rise R.C building construction.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.940-945
• /
• 1998

Recently, serious cracking problems have been reported in this country while the process of actual massive concrete construction. he hydration heat arising from the chemical reaction of cement with water causes temperature differentials in between inside and outside of a structural member, and these temperature differentials induce thermal stresses. In this paper, we described on the practical application and quality control of the mass concrete mixed with fly-ash. This project is investigating adiabatic temperature rise test of concrete, mock-up test in the laboratory, ad B/P before placing the mass concrete in site. As a result, we can be prevent temperature cracking from the cement hydration heat of mass concrete and also can be showed up secure quality control flow chart of mass concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.21-22
• /
• 2022

In order to improve the strength degradation of the cement-based material to which strong alkaline liquid red mud was added, the liquid red mud was neutralized with sulfuric acid and added to the cement paste to examine the mechanical properties according to the amount added. As a result of measuring the compressive strength, the strength was higher when the red mud was neutralized with sulfuric acid and added to the cement paste than the cement paste to which the liquid red mud was added. As a result of hydration heat measurement, when red mud was neutralized with sulfuric acid and added to the cement paste, an initial strength higher than that of liquid red mud was expressed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2002.05a
• /
• pp.7-12
• /
• 2002

The purpose of this study is to design and to apply the self-compaction concrete mixture to field, having not only high strength but also compensation for shrinkage without thermal crack under 4 sides outer restraint of the member. In the experimental mix, replacement ratio of limestone Powder, CSA expansive additives, and unit water were selected as parameters, using portland blast-furnace slag cement. And, bleeding test, expansibility test, hydration heat analysis were performed. As a results, when Cement is replaced with 35% limestone Powder, 6% CSA expansive additives at unit water 175kg/$m^3$, demanded performances of fresh and hardened self-compaction concrete are accomplished in the field application.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.347-350
• /
• 2005

The strength level for removal of lining concrete in tunnel is increased from 2.94MPa to 4.9MPa in 2004. This result in the increase of concrete curing time, and construction time would be delayed. In this study, in order to improve the efficiency of construction cycle and satisfy the strength criterion, a curing method is adopted, which is considering the hydration heat in the lining concrete member. As a result, it is shown that the concrete curing time for form removal is about 20hrs without the adjustment of concrete mix design. And construction cycle time is not changed compared to that before the change of strength criterion.