• 교육시설 논문지
• /
• 제18권3호
• /
• pp.35-41
• /
• 2011

Performance of a small-capacity solar absorption cooling system was investigated experimentally. Ten sets of evacuative-tube solar-heat collectors and a 5 kW single-stage absorption cooler were combined to produce a hybrid cooling system. The performance of the cooling system was measured using a tim-coil unit installed in a small plastic storage. It was found from the test on a sunny day of May that when the temperature of the hot water supplied from the solar collectors to the generator of the absorption cooler reached $60^{\circ}C$, the absorption cooler started cooling and the cold water temperature measured from the fan-coil unit reached $18^{\circ}C$. The COP, which is defined as the ratio of the cooling power to the total electrical power input was higher than 1.0.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.200-210
• /
• 1997

This paper presents the thermal behaviours of a solid type disk brake for a high-speed train. The thermal behaviours of a brake disk with 50mm thickness shows good performance compared with 45mm thickness of a disk because of a high specific heat capacity and thermal expansion ratio. The FEM results show that the thickness of the d!sk with a same weight of the brake disk should be increased for a good flexibility of the contact thermal problems. Therefore, the ratio between the pad and disk in diameter may be reduced and the thickness of a disk increased.

• Elastomers and Composites
• /
• 제42권3호
• /
• pp.177-185
• /
• 2007

유기화된 montmorillonite(O-MMT)와 인을 포함하는 polyamic acid(PPAA)를 용액 블렌딩하여 PAA/organoclay 나노 복합체를 제조하였다. 이들 나노 복합체들의 연구를 위하여 FT-IR, DSC, TGA, PCFC, SEM 그리고 XRD를 이용하였다. 나노복합체들의 제조확인은 FT-IR과 XRD 분석을 통하여 확인하였다. SEM 사진들은 O-MMT가 매트릭스 고분자에 비교적 고르게 분산되어 있음을 보여 주었고, XRD 결과를 통하여 O-MMT가 intercalation 되었음을 확인하였다. O-MMT/PPAA 나노복합체들의 열안정성 및 난연성은 순수한 PAA 보다 크게 높았으며, O-MMT/PPAA-0.2, 0.4, 0.6 복합체들의 열방출 용량과 총열방출 값들은 인의 함량 증가와 함께 감소하였다. 본 연구에서 제조된 나노복합체 필름들이 화재안전재료로서 사용될 수 있는 잠재성을 가지고 있음을 확인하였다.

• 설비공학논문집
• /
• 제10권1호
• /
• pp.79-87
• /
• 1998

Basic design of a 50USRT(175㎾) triple effect absorption chiller driven by hot gas has been carried out for both parallel and series flow cycles. Parallel flow cycle showed higher COP, however, the temperature in the generator was also higher than that in series flow cycle. Dynamic operation behavior of a parallel flow system at off-design conditions, such as the change in heat transfer medium temperature or the construction change of the system components, has been investigated in detail. It was found that the cooling capacity was seriously decreased by reducing hot gas flow rate and UA-value in the high temperature generator. However, the system COP was improved, because thermal load in the system components was reduced. The COP and the cooling capacity was found to be improved as cooling water temperature decreased or chilled water temperature increased. The optimum ratio of solution distribution could be suggested by considering the COP, the cooling capacity and the highest temperature in the system, which is critical for corrosion.

• 한국수산과학회지
• /
• 제23권5호
• /
• pp.401-406
• /
• 1990

In order to assess fish meal as food protein source which contains heat denatured pro-tein, functional properties of fish meal protein to be treated with alkaline were examined. Ratio of fish meal to 0.2N NaOH solution for extract solvent which were 1:10 showed good results of extracted and recovered amount of fish meal protein. pH 4.5, solubility of protein treated with alkaline revealed the lowest value. Until concentrations of alkaline treated protein solution reached $0.7\%$, its emulsifying capacity steeply decreased. Emusifying capacity of alkali treated protein were higher value at pH 9.0 than pH 4.0 and 7.0, and also were higher quantity in 0.5M NaCl solution than that of 0.1M. Heating time of fish meal protein to be treated with alkaline reached until 30 mins, its fat binding capacity indicated little change and that of heating time 60 mins decreased. Gel forming concentrations of fish meal protein to be treated with alkali for 15 mins or less were $20\%$ but those of 30 and 60 mins were $25\%$. When treating time of fish meal protein with alkali solution reached till 20 mins, viscosity of alkali treated protein solution steeply decreased.

• 대한기계학회논문집
• /
• 제16권11호
• /
• pp.2196-2202
• /
• 1992

본 연구에서는 초전도 양자 간섭장치(SQUID, superconductiong quantum inte- rference device)를 냉각시킬 수 있는 정도의 소용량(3.995K에서 0.1W)의 GM/J-T 냉동 기에 대하여 요구되는 냉각용량을 만족시키면서 최대의 성능을 나타낼 수 있는 열교환 기의 면적배분 조건을 구하였다. 즉 냉동 성능을 알고 있는 상용 2단 GM 냉동기와 소형 극저온 냉동기에 널리 사용되는 열교환기로 이루어진 복합적인 GM/J-T 냉동기에 대하여 열교환기 총면적이 주어졌을 때, J-T 회로내의 냉매(헬륨)의 유량과 각 열교환 기 전열 면적의 비를 변수로 최적설계를 행하였다.

• 대한기계학회논문집B
• /
• 제21권8호
• /
• pp.996-1008
• /
• 1997

This paper describes a methodology and results for the analysis of a small steam injected gas turbine cogeneration system. A performance analysis program for the gas turbine engine is utilized with modifications required for the model of steam injection and the heat recovery steam generator (HRSG). The object of simulation is a simple cycle gas turbine engine under development which adopts a centrifugal compressor. The analysis is based on the off-design operation of the gas turbine and the compressor performance map is utilized. Analyses are carried out with the injection ratio as the main parameter. The effect of steam injection on the power and efficiency of gas turbine and cogeneration capacity is investigated. Also presented is the variation in the main operating parameters inside the HRSG. Remarkable reduction in NOx generation by steam injection is confirmed. In addition, it is observed that for the 100% power operation the temperature of the cooled first nozzle blade decreases by 100.deg. C at full steam injection, which seems to have a favorable effect on the engine life time.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권5호
• /
• pp.728-734
• /
• 2004

Environmentally friendly refrigerants with zero ozone layer depletion potential are required to be used in refrigerators and air conditioners due to the difficulties related to ozone layer depletion and global warming. A rigorous study for the system performance with new refrigerants having zero ozone layer depletion potential is inevitable before adopting that as a new fluid. The HFC(Hydrofluorocarbon) potential has been recommended as alternatives. In this paper. system performance in the heat pump facilities were studied using R-290, R-600a. R-1270 as an environment friendly refrigerant. R-22 as a HCFC's refrigerant. The experimental apparatus has been set-up as a conventional vapor compression type heat Pump system. The test section is a horizontal double pipe heat exchanger. A tube diameter of 12.70mm with 1.315mm wall thickness is used for this investigation. The test results showed that the COP of hydrocarbon refrigerants were superior to that of R-22 and the maximum increasing rate of COP was found in R-1270. The refrigeration capacity of hydrocarbon refrigerants were higher than that of R-22. The compressor work was obtained with the maximum value in R-1270 and the minimum one in R-22.

• 에너지공학
• /
• 제25권3호
• /
• pp.59-65
• /
• 2016

MVR 증발법은 담수의 증발을 위해 연료를 지속적으로 연소시켜 나오는 열에너지를 이용하지 않고 대신 전기압축기를 통해 증발된 증기를 압축시켜 고온으로 만들고, 이를 다시 열교환기를 통해 재활용함으로써 에너지의 소비를 최소화하는 방식이다. MVR 증발법은 안정적이라 할 수 있는 계통선에 의해 공급되는 전기 대신 가변적인 풍력에너지를 그 에너지원으로 활용하여 담수 생산을 꾀할 수 있다. 본 연구에서는 일일 담수 생산량이 30 톤인 제주 MVR 담수화 시스템의 설계, 제작 그리고 작동 과정에 대하여 살펴보고자 하였다. 실험결과, MVR 압축비는 1.5 이상이며 주열교환기의 온도차는 $5{\sim}7^{\circ}C$로 설계치와 동일한 성능을 보여준다.

• 한국자동차공학회논문집
• /
• 제17권3호
• /
• pp.45-53
• /
• 2009

Die casting process of Mg alloys for high temperature applications was studied to produce an engine oil pan. The aim of this paper is to evaluate die casting processes of the Aluminium oil pan and in parallel to apply new Mg alloy for die casting the oil pan. Temperature distributions of the die and flow pattern of the alloys in cavity were simulated to diecast a new Mg alloy by the flow simulation software. Dies have to be modified according to material characteristics because melting temperature and heat capacity are different. We changed the shape and position of runner, gate, vent hole and overflow by the simulation results. After several trial and error, oil pans of AE44 and MRI153M Mg alloys are produced successfully without defect. Sleeve filling ratio, cavity filling time and shot speed of die casting machine are important parameter to minimize the defect for die casting Magnesium alloy.