• Journal of Power System Engineering
• /
• v.2 no.3
• /
• pp.49-54
• /
• 1998

This paper is investigated of hardness and adhesiveness of plasma sprayed coating steels by AE(Acoustic Emission) testing when loading a tensile. AE Parameters used are Event, Count, Energy and Amplitude. Test specimens are carbon steel(S45C) with sprayed coating layers of Ni-4.5wt.%Al(bond coating) and $TiO_2$(top coating), and carry out heat treatment at $800^{\circ}C\;and\;1000^{\circ}C$, respectively. The micro-hardness of the heat treatment specimen have been improved more than that of non-heat treatment. On the tensile test, the process and occurence of the exfoliation of the sprayed coating layer can be estimated by AE Characteristics of AE parameters, such as event, count, amplitude and energy, on the layer exfoliation are shown the similar aspects. The exfoliation of bond coating occure at about 20% of strain and top coating is about 5% of strain.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.6
• /
• pp.806-813
• /
• 1999

The effect of Post-Weld Heat Treatment(PWHT) of SS400 Steel was investigated with parameters such as micro vickers hardness corrosion potential polarization behaviors galvanic current Al anode generating current Al anode weight loss etc. Hardness of each parts(HAZ, BM, WM)by PWHT is lower than that of each parts by Non Post-Weld Heat Treatment(NPWHT) However hardness of WM of HAZ part was the highest among those three parts and HAZ area were also acted as cathode without any case of heat treatment. Potential difference between each three parts by PWHT was also smaller compared to NPWHT. Therefore it is suggested that Corrosion resistance property is increased by PWHT. However both Al anode generating current and anode weight loss was also decreased by PWHT compared to NPWHT when SS400 steel is cathodically protected by Al anode.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.3
• /
• pp.159-164
• /
• 1997

Non-alloyed and 1.0%Ni alloyed ductile cast iron were cast into the sand mold and metal mold, and finer graphite size was obtained in case of metal mold casting. Direct tempering after casting showed the slight increase of absorbed energy, which is largely due to the relieving of residual stress that is developed during casting. After austempering heat treatment, higher impact energy was obtained in case of metal mold casting than sand mold casting, which is due to the finer graphite size.

• Journal of the Korean institute of surface engineering
• /
• v.22 no.3
• /
• pp.109-117
• /
• 1989

The effect of heft treatment on the characteristic properties of insulation layer is studied for two kinds of non-oriented silicon steels, which were insulation-coates with various kinds of inorganic and inorganic-organic complex coating solutions. In addition, how the carbon contained in the insulation layer would affect the carbon content and the magnetic properties of the steel substrates is examined. Lower temperature heat treftment ($480^{\circ}C$ for 0.5hr) is found to render morw favorable surface qualities, wheras higher temperature heat treatment ($790^{\circ}C$ for 2hr) better core loss due to grin growt occurred during the heat treatment. Decarburization of the steel substrate is also found unaffectrd by the presence of carbon in the insulation layer.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.218-228
• /
• 1991

Since heat exchangers are composed of bank of tubes, the knowledge on the flow and heat transfer characteristics of the tube bank are required for the optimum design and selection of heat exchangers. In this paper, the turbulent flow fields and heat transfers normal to a staggered tube bank are solved numerically employing K-.epsilon. 2 equation turbulence model and non-orthogonal coordinate transformation for the treatment of curved surface of tubes. Predicted mean Nusselt numbers of tube bank agree reasonably well with Grimision's correlation

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.419-426
• /
• 2011

In this study, an experimental and theoretical program were carried out to determine the cutting forces and chip formation at different cutting speeds using a 0.4mm nose radius ceramic insert and -7 rake angle for non heat-treated AISI 4140 (27HRc) and heat-treated AISI 4140 (45 HRc) steel. The results obtained were compared to show the hardness differences between the materials. The secondary deformation zone thicknesses when comparing the two materials show different physical structure but similar size. These results were also discussed in light of the heat treatment and the effects it had on the machining characteristics of the material. In addition, the Oxley Machining Theory was used to predict the cutting forces for these materials and a comparison made. The predicted cutting performances were verified experimentally and showed good agreement with experimental data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.24-25
• /
• 2008

The effect of heat treatment in $HfO_2$ as charge trap with $SiO_2/Si_3N_4/SiO_2$ as tunnel oxide layer in capacitors has been investigated. Rapid thermal annealing (RTA) were carried out at the temperature range of 600 - $900^{\circ}C$. It is found that all devices carried out heat treatment have large threshold voltage shift Especially, device performed heat treatment at $900^{\circ}C$ has been confirmed the largest memory window. Also, Threshold voltage shift of device used conventional $SiO_2$ as tunnel oxide layer was smaller than that with $SiO_2/Si_3N_4/SiO_2$.

• Journal of Korea Foundry Society
• /
• v.32 no.5
• /
• pp.231-240
• /
• 2012

In present study, the effect of heat treatment on the microstructure and mechanical properties of the gravity cast superchargers housing using A356 alloy were investigated. In order to identify the characteristics of superchagers housing casting with heat treatment, Vickers hardness test, electrical conductivity test, opical and scanning electron microscopy were performed. And also, to investigate their mechanical properties, the T6 treated superchagers housing casting in optimum heat treatment condition were carried out tensile test using UTM (Universal Testing Machine).

• Food Science and Biotechnology
• /
• v.15 no.4
• /
• pp.529-533
• /
• 2006

To produce fresh-cut fruit products of high quality, the combined effects of postharvest calcium and heat treatment on Tsugaru apple were examined. Whole fruits were treated for 20 min at three different conditions: dipping in 3% $CaCl_2$ solution at $45^{\circ}C$ or ambient temperature, or in heated water at $45^{\circ}C$. The calcium content of the apples dipped in $CaCl_2$ solution at $45^{\circ}C$ was higher than that of the control and the non-heated calcium dipping. The fruits with calcium and heat treatment showed the same pattern of respiration rates as the control did during storage. The browning degree of the apple slices increased to approximately 3% after one-day storage, but no significant difference was observed between the treated and untreated apples. The fruits with $CaCl_2$ solution dipping at $45^{\circ}C$ had higher firmness than those with calcium dipping or heat treatment alone.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.2
• /
• pp.97-104
• /
• 2021

This study aims to develop non-sintered cement that can replace the Portland cement by utilizing industrial by-products. As a suggestion, the physical properties of non-sintered cement mortar depending on the curing method were investigated with ground granulated blast furnace slag, class C fly ash, and class F fly ash. As a result of the study, it was found that the strength performance and absorption rate were improved through the heat treatment process after steam curing. It was confirmed through crystal phase analysis that the hydration was accelerated after heat treatment, and the bonding material formed a dense internal structure.