• 대한두경부종양학회지
• /
• 제26권2호
• /
• pp.187-192
• /
• 2010

Background and Objectives : LED(Light emitting diode) is recently introduced as a energy-saving light source in many area including agriculture and environment. In medical field it is known as bright and safe light source in surgical lighting including headlight. This study is aimed to test effectiveness and cost-saving of mountain-climbing headlight in comparison with xenon headlight. Materials and Methods : Internet market-available mountain-climbing headlight was compared with medical xenon headlight regarding heat generation after 30 minutes' usage, intensity of illumination and possible burn to the perioral skin. To get temperature data, 5 cases of tonsillectomy were done with the aid of LED headlight, while another 5 tonsillectomies were done using xenon headlight. Results : The temperatures of all light sources were below 45 degrees Celcius until finish of the surgery without burn or complications. No differences in operation time with both headlights. The maximal intensities of illumination were 24000 Lux for xenon, 20000 Lux for LED. Conclusion : Mountain-climbing headlight could be safe and helpful light source with low cost in simple oral surgery.

• 한국도로학회논문집
• /
• 제19권6호
• /
• pp.165-173
• /
• 2017

PURPOSES : The current practice in car headlight visibility performance evaluation is based on the luminous intensity and illuminance of headlight. Such practice can be inappropriate from a visibility point of view where visibility indicates abilities to perceive an object ahead on the road. This study aimed at evaluating the appropriateness of current headlight evaluation method. METHODS : This study measured the luminance of object and road surface at unlit roadways. The variables were measured by vehicle type and by headlight lamp type. Based on the measurements, the distance where drivers can perceive an object ahead was calculated and then compared against such distance obtained by conventional visibility performance evaluation. RESULTS : The evaluation method based on illuminance of headlight is not appropriate when viewed from the visibility concept that is based on object-perceivable distance. Further, the results indicated a shorter object-perceiving distance even when road surface luminance is higher, thereby suggesting that illuminance of headlight and luminance of road surface are not the representative indices of nighttime visibility. CONCLUSIONS : Considering that this study utilized limited vehicle types and that road surface (background) luminance can vary depending on the characteristics of the given road surface, it would likely go too far to argue that this study's visibility performance evaluation results can get generalized to other conditions. Regardless, there is little doubt that the current performance evaluation criterion which is based on illuminance, is unreasonable. There should be future endeavors on the current subject which will need to explore study conditions further, under which more experiments should be conducted and effective methodologies developed for evaluating automotive headlight visibility performance. Needs are recognized particularly in the development of headlight visibility performance evaluation methodology which will take into account road surface (background) luminance and luminance contrast from various perspectives as the former indicates the driver's perception of the front road alignment and the latter being indicative of object perception performance.

• 대한인간공학회지
• /
• 제7권1호
• /
• pp.39-44
• /
• 1988

Because the moving visual acuity is less than the static visual acuity, a new headlight system was designed and manufactured to make reparation for that. Then the new headlight system was built in a passenger car and some experiment was achieved. When the car is accelerated the luminous flux of headlight is augmented. When the speed of the car was increasing, the new system was effective, but when the car was decelerated the system was less effective.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1517-1522
• /
• 2011

Recently, application of LED luminaires has been issued for energy saving plan. In this paper, we carried out a study to replace a low efficacy sealed-beam lamp for headlight of railroad vehicles with LED luminaire. Electrical and optical characteristics of the sealed-beam lamp were analyzed and a LED headlight was designed and fabricated. Total luminous efficacy and rated power of the prototype LED headlight were 82 lm/W ; about 5 times higher, and 40W ; about 4 times lower than the sealed-beam lamp, respectively. Especially, lifetime of the sealed-beam lamp is short as 1,000 hours due to the evaporation and vibration of filament, but that of LED headlight is over 30,000 hours long.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.1398-1401
• /
• 2004

In case the problem came into the headlight composed of a bulb, lens and reflecting mirror, it has a sealed-beam type which must exchange all and semi-sealed beam type which can exchange only bulb. The headlight of train must be used at the time of going into tunnel and atmospheric phenomena such as heavy snow, rain and foggy as a rule, also it can be used with whistle blow when the dangerous article appears. In this study, general technical specification to improve headlight of the KTX and G7 high speed train is described throughout investigation technique of the industrialized country and headlight specification of train which is on commercial service.

• 자동차안전학회지
• /
• 제12권3호
• /
• pp.7-12
• /
• 2020

This paper has presented the headlight inspection standards and methods of two-wheeled motorcycles considering Korean Motor Vehicle Safety Standards (KMVSS), Korean Motor Vehicle Inspection Standards (KMVI) and the inspection standards of the International Motor Vehicle Inspection Committee (CITA). As a result of analyzing the headlight luminous intensity test result with fixed inspection equipment, 21% does not meet the inspection standard proposed in this study, and 33.3% in mobile inspection equipment does not meet. The average luminous intensity of motorcycle less than 50 cc is 8,340 cd, so all the lightweight small sized motor cycles do not meet the proposed headlight inspection standard.

• 품질경영학회지
• /
• 제46권3호
• /
• pp.641-650
• /
• 2018

Purpose: This article provides a cause of breakage and a method for improving reliability of the headlight system installed in the main battle tank K2. Method: The natural frequency of the headlight system is estimated by using the finite element method. In addition, the allowable stress level under the severe conditions is provided through vibration test of a single item and a system level. Results: Based on the finite element analysis and the vibration test in the frequency domain, the lamp of the left headlight system fails by the resonance effect. Conclusion: For improving the reliability of the headlight system, the thickness of protector frame is increased to avoid the resonance effect.

• 조명전기설비학회논문지
• /
• 제18권6호
• /
• pp.14-21
• /
• 2004

본 논문에서는 평지, 오르막 및 내리막에서 야간 운전할 때에 생기는 눈부심에 대해 헤드라이트를 자동 조절하여 운전자가 안전하게 운전을 할 수 있는 알고리즘을 제안하였다. 먼저 광센서를 이용해 전방에 차량이 접근하는지의 유무를 판단하고 기울기센서로써 차량의 기울어진 정도를 계속적으로 판단하도록 하였다. 이러한 정보를 이용하여 헤드라이트를 조절하는 서보모터를 제어함으로써 현 운행환경조건에 맞도록 조절할 수 있도록 하였다. 본 논문에서 제안한 헤드라이트 자동조절시스템은 평지 및 경사로에서 실제로 측정한 조도량에 대한 데이터를 바탕으로 하여 제작되었고, 테스트 모델에 의해 얻은 실험결과를 통해 환경과 조건에 따라 제대로 작동하고 효과가 있음을 확인하였고, 따라서 본 알고리즘의 유효성을 증명하였다.

• Journal of the Optical Society of Korea
• /
• 제20권1호
• /
• pp.118-124
• /
• 2016

The shape and location of the cutoff shield in a projection-type headlight system were optimized by a ray-tracing technique. A shield based on a Petsval surface showed better cutoff characteristics than a flat or cylindrical shield, such as a sharp intensity gradient and less color separation at the cutoff line. Adjustment of the shield’s location between the reflector and the aspheric lens further improved its cutoff characteristics.

• ETRI Journal
• /
• 제36권3호
• /
• pp.439-449
• /
• 2014

In this paper, a novel vision-based nighttime vehicle detection approach is presented, combining state machines and downhill simplex optimization. In the proposed approach, vehicle detection is modeled as a sequential state transition problem; that is, vehicle arrival, moving, and departure at a chosen detection area. More specifically, the number of bright pixels and their differences, in a chosen area of interest, are calculated and fed into the proposed state machine to detect vehicles. After a vehicle is detected, the location of the headlights is determined using the downhill simplex method. In the proposed optimization process, various headlights were evaluated for possible headlight positions on the detected vehicles; allowing for an optimal headlight position to be located. Simulation results were provided to show the robustness of the proposed approach for nighttime vehicle and headlight detection.