• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.18-19
• /
• 2006

In this study, dielectric properties of the ${Mg_5}{B_4}{O_{15}}$ (B=Ta, Nb) cation-deficient perovskite ceramics and its oscillator application are investigated. The cation-deficient perovskite ceramics are prepared through the solid-state route. According to the XRD pattern, ${Mg_4}{Ta_2}{O_9}$ and $Mg{Ta_2}{O_6}$ phase existed in calcined and sintered ${Mg_5}{Ta_4}{O_15}$ powder. Also ${Mg_5}{Ta_4}{O_{15}}$ phase added with increasing sintering temperature. In the case of calcined and sintered ${Mg_5}{Nb_4}{O_{15}}$ powder, single phase of ${Mg_5}{Nb_4}{O_{15}}$ is appeared. In the case of the ${Mg_5}{Ta_4}{O_{15}}$ and ${Mg_5}{Nb_4}{O_{15}}$ ceramics sintered at $1450^{\circ}C$ for 5h, the dielectric constant, quality factor, and temperature coefficient of the resonant frequency (TCRF) were 8.2, 259,473 GHz, $-10.91ppm/^{\circ}C$ and 14, 37,350 GHz, $-52.3\;ppm/^{\circ}C$, respectively. Simulated DR with ${Mg_5}{Ta_4}{O_{15}}$ ceramics had the operating frequency of 10.99 GHz and S(2,1) of -29.795 dB. Size of manufactured oscillator was $56{\times}48{\times}34\;mm^3 and operated at 11.93 GHz. Power output and second harmonic of oscillator were +13.61 dBm and -23.81 dBc at 23.85 GHz, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.60-68
• /
• 2007

A technique is presented to extract differential second harmonic output from common source nodes of a cross-coupled P-& N-FET oscillator. Provided the impedances at the common source nodes are optimized and the fundamental swing at the VCO core stays in a proper mode, it is found that the amplitude and phase errors can be kept within $0{\sim}1.6dB$ and $+2.2^{\circ}{\sim}-5.6^{\circ}$, respectively, over all process/temperature/voltage corners. Moreover, an impedance-tuning circuit is proposed to compensate any unexpectedly high errors on the differential signal output. A Prototype 5-GHz VCO with a 2.5-Hz LC resonator is implemented in $0.18-{\mu}m$ CMOS. The error signal between the differential outputs has been measured to be as low as -70 dBm with the aid of the tuning circuit. It implies the push-push outputs are satisfactorily differential with the amplitude and phase errors well less than 0.34 dB and $1^{\circ}$, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.2
• /
• pp.72-75
• /
• 2012

In this paper, high-efficiency DC-AC converter is implemented for the wireless power transmission. The DC-AC converter is implemented by combining the oscillator and power amplifier. Because the conversion efficiency of wireless power transmitter is strongly affected by the efficiency of power amplifier, the high-efficiency power amplifier is implemented by using the Class-E amplifier structure. Also, because the output power of oscillator connected to the input stage of power amplifier is low, high-gain two-stages power amplifier using the drive amplifier is implemented to realize the high-output power DC-AC converter. The dual band harmonic suppression filter is implemented to suppress 2nd, 3rd harmonics of 13.56 MHz. The output power and conversion efficiency of DC-AC converter are 40 dBm and 80.2 % at the operation frequency of 13.56 MHz.

• Korean Journal of Optics and Photonics
• /
• v.31 no.3
• /
• pp.142-147
• /
• 2020

In this paper, we report highly efficient second harmonic generation of continuous-wave Yb fiber lasers incorporating a periodically poled LiTaO₃ device (MgO:PPSLT) as a frequency converter. The seed laser output from a Yb fiber master oscillator using a Fabry-Perot feedback cavity was amplified in a Yb fiber amplifier stage, yielding 28.5 W of linearly polarized output at 1064 nm in a beam with beam quality, M², of ~1.07. Second harmonic generation was achieved by passing the laser beam through MgO:PPSLT. Under optimized conditions, we obtained 11.1 W of green laser output at 532 nm for an incident signal power of 25.0 W at 1064 nm, corresponding to a conversion efficiency of 44.4%. The detailed investigation to find the optimized operating conditions and prospects for further improvement are discussed.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.210-215
• /
• 2006

In this paper, we develop the PLL system of the local oscillator system using Gunn oscillator VCO for millimeter wave band receiving system. The local oscillator system consists of the $86{\sim}115GHz$ Gunn. diode oscillator part, the RF processing part including the diplexer and the harmonic mixer, and the DPLL system including Gunn modulator and controller. Based on this configuration, we verify the frequency and power stability of the developed local oscillator system. We developed system which applied to DPLL technique instead of the existing analog PLL method to accomplish this purpose. The developed system for this purpose is tested the frequency and power stability for a long time to confirm performance. Since we confirmed this system that had frequency characteristic of within ${\pm}10Hz$, very fine output drift power characteristic of $0.2{\sim}0.3dBm$ and about 200MHz locking range, it verified suitable for cosmic radio receiving system through the test result.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.2
• /
• pp.137-144
• /
• 2008

In this paper, a novel voltage-controlled oscillator(VCO) using the output matching network based on the harmonic control circuit is presented for improving the phase noise property. The phase noise suppression is achieved through the harmonic control circuit having the short impedances for both second-harmonic and third-harmonic components, which has been connected at the output matching network. Also, we have used the microstrip square open loop multiple split-ring resonator(OLMSRR) having the high-Q property to further reduce the phase noise of VCO. Because the output matching network based on the harmonic control circuit has been used for reducing the phase noise property instead of the High-Q resonator, we can obtain the broad tuning range by the low-Q resonator. The phase noise of the proposed VCO using the output matching network based on the harmonic control circuit and the microstrip square OLMSRR has been $-127.5{\sim}126.33$ dBc/Hz @ 100 kHz in the tuning range, $5.744{\sim}5.839$ GHz. Compared with the reference VCO using the output matching network without the harmonic control circuit and the microstrip line resonator, the phase noise property of the proposed VCO has been improved in 26.66 dB.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.4
• /
• pp.46-52
• /
• 2009

In this paper, a novel VCO (Voltage Controlled Oscillator) structure is proposed to achieve the characteristic of low phase noise and a wide frequency tuning range. The proposed scheme adopts an impedance transforming technique to change a series resonance into a parallel resonance for maximizing the susceptance slope parameter. The manufactured VCO shows a frequency tuning bandwidth of 600MHz from 10.1GHz to 10.7GHz with a tuning voltage varying from 0 to 9V, an excellent phase noise below -119dBc/Hz@1MHz offset. The harmonic suppression is measured above 28dB.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.770-773
• /
• 2002

Two sinusoidal voltage-controlled oscillators using linear operational transconductance amplifiers are presented in this paper: One is based on the positive-feedback bandpass oscillator model and the other on the negative-feedback Colpitts model. The bandpass VCO consists of a noninverting amplifier and a current-controlled LC-tuned circuit which is realized by two linear OTA's and two grounded capacitors, while the Colpitts VCO consists of an inverting amplifier and a current-controlled LC-tuned circuit realized by three linear OTA's and three grounded capacitors. Prototype circuits have been built with discrete components. The experimental results have shown that the Colpitts VCO has a linearity error of less than 5 percent, a temperature coefficient of less than rm 100 ppm/$^{circ}C$, and a $pm1.5 Hz $frequency drift over an oscillation frequency range from 712Hz to 6.3kHz. A total harmonic distortion of 0.3 percent has been measured for a 3.3kHz oscillation and the corresponding peak-to-peak amplitude was 1V. The experimental results for bandpass VCO are also presented.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.411-415
• /
• 2003

In this paper, a reflector type frequency doubler for local oscillator at 24GHz is designed and fabricated with ne71300-N MESFET. Optimum source and load impedances are decided through a multiharmonic load pull simulation technique. A conversion gain ran be improved using the reflector and fundamental and third harmonics are well suppressed with open stub of λ/4 length. Measured results show output power at 0dBm of input power is -3.776dBm, conversion gain 0.736dB, harmonic suppression 41.064dBc, respectively.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.15-27
• /
• 2014

양자화학 (quantum chemistry)을 처음 접했을 때, 이전까지의 고전역학 (classical mechanics)에 익숙한 대다수의 학생들은 양자화학을 받아들이는 데 어려움을 겪는다. 모형계에 양자역학 (quantum mechanics)을 직접 적용하여 봄으로써 생소한 양자 개념에 대한 이해를 도울 수 있다. 본 논문에서는 양자동역학 (quantum dynamics)을 수치적으로 구현하는 계산 프로그램을 모형계에 적용하여 양자 개념을 설명할 수 있는 몇 가지 예를 보이고자 한다. 1 차원 시간의존 슈뢰딩거 방정식 (1-D time-dependent $Schr{\ddot{o}}dinger$ equation)의 해를 얻어 양자동역학을 구현하였으며, 그에 해당하는 고전동역학은 뉴턴 방정식 (Newton's equation)의 해로 얻어졌다. 조화 진동자 퍼텐셜 (harmonic oscillator potential), 모스 진동자 퍼텐셜 (Morse oscillator potential), 이중 우물 퍼텐셜 (double-well potential), 네모 퍼텐셜 장벽 (rectangular potential barrier), 그리고 에카트 퍼텐셜 (Eckart potential)에 대한 계산을 수행하였다. 두 가지 동역학을 비교하기 위하여 계산 결과의 시각화 (visualization)를 이용하고 동역학 특성의 차이를 비교하는 차별화 (differentiation)를 강조한다. 영점에너지 (zero-point energy), 위상어긋남 (dephasing), 터널링 (tunneling), 그리고 반사 (reflection) 현상과 같은 양자동역학의 특징을 고전동역학과 비교함으로써 직관적인 이해를 도울 수 있었다. 이러한 결과는 양자화학에 입문하는 학생들을 대상으로 쓰일 수 있는 효율적인 강의 모델을 제시할 것으로 기대한다.