• 한국구조물진단유지관리공학회 논문집
• /
• 제8권3호
• /
• pp.197-205
• /
• 2004

연약지반 개량을 위해 진공압밀공법을 적용할 경우 발생되는 Hardening Zone의 범위와 진공압 세기의 관계를 연구하였다. 이를 위하여 단위 셀 형식의 시험기를 제작하여 국내의 대표적 준설매립공사지역인 광양, 부산, 목포에서 채취한 고함수비 상태에서의 준설점성토에 대해 각각 함수비와 콘저항치수를 측정하여 진공압의 변화에 따른 Hardening Zone의 변화를 파악하였다. 높은 진공압상태에서는 배수재의 막힘현상과 배수재 부근에서 빠르게 생성되는 Hardening Zone 등으로 인하여 배수층으로의 간극수의 흐름이 방해되어 낮은 진공압상태에서 보다 Hardening zone의 범위가 커지지는 않았다.

• 한국정밀공학회지
• /
• 제10권4호
• /
• pp.64-72
• /
• 1993

Analytical models for the prediction of the size of hardened zone in laser surface hardening are presented. The models are based on the solutions to the problem of three-dimensional heat flow in plates with infinite thickness. The validity of the model was tested on medium carbon steel for Gaussian mode of beam. Then the model for rectagular beam was used for the predicition of the size of hardened zone on various hardening process parameters. From the calculation results it appeared that the size and shape of the hardened zone are strongly dependent on process parameters such as beam mode, beam size, and traverse speed.

• 대한토목학회논문집
• /
• 제28권2C호
• /
• pp.75-81
• /
• 2008

본 연구에서는 연약지반을 목적에 맞게 개선하기 위한 방법으로 성토하중 및 멤브레인 등이 필요치 않은 석션드레인(Suction Drain)공법의 개량기간 및 적용 석션압에 따른 개량도를 파악하고 Hardening Zone의 영향을 파악하기 위한 일련의 실내 토조 실험을 실시하였다. 실험 조건은 석션압 적용기간을 4일, 8일, 12일, 16일, 20일, 적용 석션압을 -20kPa, -40kPa, -60kPa, -80kPa로 달리하여 실험을 실시하였다. 실험결과 침하량의 경우, 적용된 석션압 및 처리기간이 증가함에 따라 개량도는 증가하는 양상을 나타냈으며, 점차적으로 수렴하는 경향이 나타났다. 또한, 함수비로 역산된 투수계수 저하비와 변형된 Hansbo의 방사형 압밀이론에 의해 수치적으로 예측된 투수계수 저하비를 비교/분석한 결과 2~3으로 가정한 결과에서 실측치와 예측치에 가장 부합되는 결과가 나타났으며, Hardening Zone은 전체 영역 25cm 중 약 7~8cm 범위에서 발생됨을 파악할 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.13-17
• /
• 1993

Analytical models for the prediction of the size of hardened zone in laser surface hardening are presented. The models are based on the solutions to the problem of three-dimensional heat flow in plates with infinite thickness. The validity of the model was tested on medium carbon steel for Gaaussian mode of beam. Then the model for rectangular beam was used for the prediction of the size of harened zone on various hardening process parameters. From the calculation results it appeared that the size and shape of the hardened zone are strongly dependent on process parameters suchas beam mode, beam size, and traverse speed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.921-924
• /
• 1995

Case hardening behavior of carbon tool steel(SK5) was investigated after pulsed YAG laser irradiation. In the case od beam passes,martensite formed in the melt zone and in former pearlite regions of the austenitization zone exhibits vary high Vickers hardness values. The molten depth and width decrease as the beam power density increase. The influence of depth and width of color painted specimen was also investigated. The molten zone of the black painted specimen was the largest. The were loss of the black painted specimen was smaller than any other painted or raw material.

• 소성∙가공
• /
• 제14권4호
• /
• pp.327-337
• /
• 2005

In the present work, the two back stress kinematic hardening models are proposed by combining Armstrong-Frederick, Phillips and Ziegler's hardening rules. Simple combination of hardening rules using simple rule of mixtures results in various evolutions of the kinematic hardening parameter. Using the combined hardening models the ultimate back stress fur the present models is also derived. The stress rate is co-rotated with respect to the spin of substructure due to the assumption of kinematic hardening rule in finite deformation regime. The work piece under consideration is assumed to consist of the elastic and the rigid plastic deformation zone. Then, the J2 deformation theory is facilitated to characterize the plastic deformation behavior under various loading conditions. The plastic deformation localization behaviors strongly depend on the constitutive description namely back stress evolution and its hardening parameters. Then, the analysis for Swift's effects under the fixed boundaries in axial directions is carried out using simple shear deformation.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1998년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Spring 1998
• /
• pp.28-35
• /
• 1998

The seismic overstrength factor $\Omega$ is evaluated for 4-story reinforced concrete buildings in Korea(of which seismic intensity is low). The study model is designed according to aseismic guideline research - phase II in Korea. The effect of variation of span length and bay number, dead load is considered, especially including the variation of hardening ration after yielding. And push-over analysis is performed, in which the external and internal frame is connected by rigid-link and the $\Omega$ is calculated using the roof drift ratio at 2%. For Zone I, the mean value of $\Omega$ is ranged form 2.3 to 2.5, For Zone II, from 3.1 to 3.4. For low hardening ratio(3%) after yielding, $\Omega$ has little relations with the number of bay, like as the results of other research. But for 5% hardening ratio, $\Omega$ is increased as the number of bay is increased. Within general gravity-load bound, the variation of D.L. has variation of D. L. has no effect on $\Omega$. And, $\Omega$ is increased as the span length is increased.

• 한국기계가공학회지
• /
• 제10권1호
• /
• pp.31-37
• /
• 2011

Recently, the technology of surface treatment is being more important which affects the material cost reduction and substitution to the expensive material. The material used for the mechanical processing should have not only high intensity, but also strength toughness, wear resistance and corrosion resistance. In order to increase the durability and have better quality of the parts using such kind of tooling material, various kinds of research of the surface hardening through many kinds of heat resources is being done and practically applied. In this study, the characteristics of hardening surface zone for high strength of the press die material through laser beam irradiation are researched. In this study, it is experimentally observed by the status of the surface morphology, tensile strength, the hardness distribution of the base metal and wear condition by the surface hardness pattern by the laser beam based on the process parameters of $CO_2$ laser by using SM45C and STD11 used for press tool. Through this research, the characteristics of surface hardened zone for high strength of the thin metal by laser beam irradiation is done.

• 한국레이저가공학회지
• /
• 제18권2호
• /
• pp.1-4
• /
• 2015

This study is related to the surface hardening treatment to spheroidal graphite cast iron for die by using high power diode laser. Laser device used in this experiment is capable of real-time laser power control. This is because the infrared temperature sensor (two color pyrometer) attached to the optical system measures the surface temperature of specimen and adjusts the laser power in real time. The surface treatment was carried out with the change of heat treatment temperature at the beam travel speed 3 mm/sec. Hardened width and depth was measured and hardened zone was analyzed by micro vickers hardness test in order to research the optimum condition of heat treatment. The changes in microstructure of the hardened zone also was examined. As a result of hardness measurement and observations on microstructure of hardened zone, hardness increased over three times as compared with base metal because the martensite was formed on the matrix structure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.998-1002
• /
• 1997

This study has been performed to predict beam absorption with analysis of temperature field by using a FEM in co /sab 2/ laser hardening and to invesrigate into some effects of power density and travel speed of laser beam on the microstructure and hardness of ductile cast iron treated by laser surface hardening technique. Optical micrograph has shown that large martensite and small amount of retained austenite appear in inside hardened zone. Hardness measurement has revealed that the range of maximum hardness value is Hv=415 .+-. 10. The power density increases and the travel speed decreases, the depth of hardened zone increases due to increase of input power density.