• Wind and Structures
• /
• 제25권1호
• /
• pp.39-61
• /
• 2017

Buffeting induced resonance (BIR) of hangers on long-suspension bridges is briefly reviewed, including mechanism and experimental verification. Taken the Xihoumen suspension bridge as a numerical example, sensitivities of the BIR of hangers to wind properties are investigated, including types of wind spectrum, turbulence intensity, and spacial coherence of wind fluctuations. Numerical simulations indicate that the BIR of hangers occur to both cases of different wind spectra, showing that it is insensitive to types of wind spectrum. On the other hand, it is found that the turbulence intensity affects buffeting of main cables almost in a linear manner, and so it does to the BIR of the hangers; however, the resonance factors, namely the ratio of the response of the hanger to that of the main cable, are little affected by the turbulence intensity. The spacial coherence of the wind fluctuations, although plays an important role on the buffeting responses of the main structure, has no substantial effects on the BIR of the hangers. Finally, replacement of steel strand with CFRP material has been verified as a very effective countermeasure against the BIR of hangers.

• Structural Engineering and Mechanics
• /
• 제50권2호
• /
• pp.241-255
• /
• 2014

The girder of self-anchored suspension bridge is subjected to large compression force applied by main cables. So, serious damage of the girder due to breakage of hangers may cause collapse of the whole bridge. With the time increasing, the hangers may break suddenly for their resistance capacities decrease due to corrosion. Using nonlinear static and dynamic analysis methods and adopting 3D finite element model, the responses of a concrete self-anchored suspension bridge to sudden breakage of hangers are studied in this paper. The results show that the sudden breakage of a hanger has significant effects on tensions of the hangers next to the broken hanger, bending and torsion moments of the girder, moments of the towers and reaction forces of the bearings. The results obtained from dynamic analysis method are very different from those obtained from static analysis method. The maximum tension of hanger produced by breakage of a hanger exceeds 2.2 times of its initial value, the maximum dynamic amplification factor reaches 2.54, which is larger than the value of 2.0 recommended for cable-stayed bridge in PTI codes. If two adjacent hangers on the same side of bridge break one after another, the maximum tension of other hangers exceeds 3.0 times of its initial value. If the safety factor adopted to design hanger is too small, or the hangers have been exposed to corrosion, the bridge may collapse due to breakage of two adjacent hangers.

• Structural Monitoring and Maintenance
• /
• 제2권1호
• /
• pp.65-75
• /
• 2015

Among the destruction instances of half-through arch bridges, the shorter hangers are more likely to be ruined. For a thorough investigation of the hanger system durability, we have studied vehicle impact effect on hangers with vehicle-bridge coupling method for a half-through concrete-filled-steel-tube arch bridge. A numerical method has been applied to simulate the variation of dynamic internal force (stress) in hangers under different vehicle speeds and road surface roughness. The characteristics and differences in impact effect among hangers with different length (position) are compared. The impact effect is further analyzed comprehensively based on the vehicle speed distribution model. Our results show that the dynamic internal force induced by moving vehicles inside the shorter hangers is significantly greater than that inside the longer ones. The largest difference of dynamic internal force among the hangers could be as high as 28%. Our results well explained a common phenomenon in several hanger damage accidents occurred in China. This work forms a basis for hanger system's fatigue analysis and service life evaluation. It also provides a reference to the design, management, maintenance, monitoring, and evaluation for this kind of bridge.

• 대한토목학회논문집
• /
• 제14권6호
• /
• pp.1309-1317
• /
• 1994

앵커리지 (Anchorage)가 주케이블을 지지하는 전형적인 현수교에서는 행거를 가설한 후에 보강형을 순차적으로 가설하기 때문에 시공시 행거에 별도의 긴장력이 필요없다. 이와는 달리 자정식 현수교는 가교각으로 보강형을 지지한 후 행거를 설치하게 된다. 따라서 행거 가설시 초기 긴장력을 가할 필요가 있으며 이 후 계속되는 시공과정에 의해 장력이 지속적으로 변화하게 된다. 따라서 행거의 가설방법을 변화시켜가며 이에 따른 행거장력의 변화 양상을 파악하여 가장 효율적으로 행거를 가설할 수 있는 방법을 결정할 필요가 있다. 이를 위하여 본 연구에서는 해석적인 방법을 제시하였다. 현수교 시공의 진행에 따라 단계적으로 변화하는 구조계를 모사할 수 있는 사공단계해석 알고리즘을 제시하였다. 또한 자정식 현수교에서 발생할 수 있는 기하비선형 해석모델을 제시하였다. 실물 교량을 대상으로 제시된 해석방법에 따라 가장 효과적이라고 생각되는 시공방법을 제시하였다.

• Steel and Composite Structures
• /
• 제32권4호
• /
• pp.479-495
• /
• 2019

In tied-arch bridges, the way the arch and the deck are connected may become crucial. The deck is usually suspended from hangers made out of steel pinned cables capable of resisting axial forces only. However, a proper structural response may be ensured by fixing and stiffening the hangers in order to resist, additionally, shear forces and bending moments. Thus, this paper studies the effect of different pinned and stiffened hanger arrangements on the structural behavior of the tied-arch bridges, with the intention of providing designers with useful tools at the early steps of design. Longitudinally and transversally stiffened hangers (and the effect of hinges at the hangers and their locations) are studied separately because the in-plane and the out-of-plane behavior of the bridge are uncoupled due to its symmetry. As a major conclusion, regarding the in-plane behavior, hangers composed of cables (either with vertical, $Nielsen-L\ddot{o}hse$ or network arrangements) are recommended due to its low cost and ease of erection. Alternatively, longitudinally stiffened hangers, fixed at both ends, can be used. Regarding the out-of-plane behavior, and in addition to three-dimensional arrangements of cables, of limited effectiveness, transversally stiffened hangers fixed at both ends are the most efficient arrangement. A configuration almost as efficient and, additionally, cheaper and easier to build can be achieved by locating a hinge at the end corresponding to the most flexible structural element (normally the arch). Its efficiency is further improved if the cross-section tapers from the fixed end to the pinned end.

• Smart Structures and Systems
• /
• 제23권6호
• /
• pp.683-693
• /
• 2019

In August 2012, during the passage of the typhoon Haikui (1211), large amplitude vibrations were observed on long hangers of the Xihoumen suspension Bridge, which destroyed a few viscoelastic dampers originally installed to connect a pair of hanger ropes transversely. The purpose of this study is to identify the cause of vibration and to develop countermeasures against vibration. Field measurements have been conducted in order to correlate the wind and vibration characteristics of hangers. Furthermore, a replica aeroelastic model of prototype hangers consisting of four parallel ropes was used to study the aeroelastic behavior of hanger ropes and to examine the effect of the rigid spacers on vibration mitigation. It is shown that the downstream hanger rope experiences the most violent elliptical vibration for certain wind direction, and the vibration is mainly attributed to wake interference of parallel hanger ropes. Based on wind tunnel tests and field validation, it is confirmed that four rigid spacers placed vertically at equal intervals are sufficient to suppress the wake-induced vibrations. Since the deployment of spacers on hangers, server hanger vibrations and clash of hanger ropes are never observed.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.786-793
• /
• 2006

For the purpose of developing a vibration-based tension force evaluation procedure for hangers in suspension bridges, a 3D finite element model of hangers is constructed in this paper. With the developed finite element formulation, a frequency-based sensitivity-updating algorithm is applied to identify the target cable system the proposed method is also able to identify the flexural rigidity. the axial rigidity, and the torsion rigidity of a cable. For a field application, a vibration test on hangers of the Yong Jong Grand Suspension Bridge is carried out and the collected data is used to verify the proposed method.

• Smart Structures and Systems
• /
• 제23권1호
• /
• pp.15-29
• /
• 2019

This paper addresses the problem of damage detection in suspension bridge hangers, with an emphasis on the modal flexibility method. It aims at evaluating the capability and the accuracy of the modal flexibility method to detect and locate single and multiple damages in suspension bridge hangers, with different level of severity and various locations. The study is conducted numerically and experimentally on a laboratory suspension bridge mock-up. First, the covariance-driven stochastic subspace identification is used to extract the modal parameters of the bridge from experimental data, using only output measurements data from ambient vibration. Then, the method is demonstrated for several damage scenarios and compared against other classical methods, such as: Coordinate Modal Assurance Criterion (COMAC), Enhanced Coordinate Modal Assurance Criterion (ECOMAC), Mode Shape Curvature (MSC) and Modal Strain Energy (MSE). The paper demonstrates the relative merits and shortcomings of these methods which play a significant role in the damage detection ofsuspension bridges.

• 한국구조물진단유지관리공학회 논문집
• /
• 제14권2호
• /
• pp.113-120
• /
• 2010

장대 아치교 설계 시 시공단계와 완성단계에서 발생할 수 있는 문제에 대하여 검토하고 있으나 케이블 손상에 대한 구조안전성 평가는 매우 미흡한 실정이다. 따라서 본 연구는 공용 중 충돌사고로 인한 행어 파단 시 교량의 구조안전성을 분석하는 것을 연구 목적으로 한다. 이를 위하여 행어 파단에 따른 하중을 충격함수로 이상화하여 동적 해석을 수행하였다. 행어가 파단 되었을 경우 각 행어의 최대 장력은 파단된 행어와 인접한 행어에서 발생한 것으로 나타났으며 정적 하중보다 동적 하중에서 크게 나타났다. 그러므로 장대 아치교의 구조안전성을 확보하기 위해 행어 파단에 따른 충격하중을 동적 하중으로 고려한 해석이 필요하다. 또한 본 연구의 해석 방법 및 결과는 이후 아치교 설계 시 참고자료로 활용될 수 있다.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1438-1445
• /
• 1992

본 연구에서는 그린(green)의 함수를 사용한 가선-판토그래프 계 운동 해석 방법을 개발하였다. 이 방법은 집중질량 방법이나 모우드 해석법에 비하여 더욱 해 석적이며, 모우드 해석법과는 달리 고유 진동수나 진동형의 계산이 필요하지 않다.