• 한국분무공학회지
• /
• 제20권3호
• /
• pp.181-186
• /
• 2015

This study presents the dynamic wetting characteristics of an impact droplet on hole-patterned textured surfaces. The flat surfaces were manufactured by a drilling machine to generate the micro-order holes, leading to make the surface hydrophobic. Other flat surfaces were fabricated by the anodizing technique to make hydrophilic texture surfaces with a nanometer order. For hydrophilic and hydrophobic textured surfaces with similar texture area fractions, the impinging droplet experiments were conducted and compared with flat surface cases. As results, an anodized textured surface decreases apparent equilibrium contact angle and increases contact diameters, because of increase in contact area and surface energy. This is attributed to more penetration inside holes from larger capillary pressure on nanometer-order holes. On the other hand, temporal evolution of the contact diameter is smaller for the hydrophobic textured surface from less penetration on the micro-order holes.

• 한국표면공학회지
• /
• 제27권3호
• /
• pp.134-142
• /
• 1994

$Al_2O_3$coatings on mild steel substrate by plasma spray process were produced to evaluate microstructural characterization and mechanical properties. As-coated $Al_2O_3$coating samplessd were subjected to two heat treat-ment conditions : ⅰ) annealing under vacuum circumstance, ⅱ) hot press treated condition. The two heat treat-ed coatings were investigated in terms of microhardness, adhesion strength, wear resistance, porosity forma-tion, and microstructures. In the case of the coatings which were subject to preparation step ⅰ, the porosity in the coating was decreased with the increase of temperature ($700^{\circ}C$-$1100^{\circ}C$), and the wear resistance, microhardnesss and adhesion strength were increased with the increase of temperature. On the other hand, in the case of the coatings which were subject to preparation step ⅱ, wear resistance and adhesion strength were improved with the increase of temperature and pressure. Experimental measurements of coatings which were produced by both preparation conditions were enhanced compare to those of as-coated coatings.

• 한국분무공학회지
• /
• 제9권2호
• /
• pp.18-23
• /
• 2004

An experimental studies of conventional gasoline fuel pump were carried out to obtain fundamental data fur liquid phase LPG injection(LPLi) system. A regenerative type and a roller-vane type of pumps were investigated in various operational condition. The experiments were performed to obtain flow rate of LPG fuel as a function of pressure differences and temperatures. The regenerative pump had too low flow rate at some experimental conditions to use this pump system for LPLi fuel supply system. On the other hand, the roller-vane type pump can be applied to the system only if its check valve is modified. Cavitation might occur in this system which can result in system noise, flow rate variation, and pump durability problem. To solve these problems the system is needed to increase $NPSH_{re}$(required net positive suction head).

• 한국분무공학회지
• /
• 제18권1호
• /
• pp.1-8
• /
• 2013

In this paper an experimental study is presented to investigate the dynamic behavior of impacting droplet onto a liquid film. The main parameters are the droplet velocity and the thickness of the liquid film. Photographic images are presented to show the formation of crown, central jet and disintegrating droplet from the central jet. The emphasis is on presenting the time evolution of crown diameter, crown height, central jet height and the size of disintegrating droplet from the central jet. The diameter and height of crown are higher for faster droplet and thinner liquid film. On the other hand, the height of central jet are higher for faster droplet and thicker liquid film. The size of disintegrating droplet from the central jet heavily depends on the droplet velocity; Larger droplet is produced with faster falling droplets.

• 한국분무공학회지
• /
• 제13권1호
• /
• pp.16-21
• /
• 2008

In the present study, the 2-fluid nozzle and 3-fluid nozzle to atomize the diesel and water with air for the fuel reformer of SOFC system were experimentally examined. In the 2-fluid nozzle, the diesel and water were alternately atomized due to bislug flow pattern, and it implies that the mixing of both liquids strongly affects the atomization pattern. On the other hand, in the 3-fluid nozzle, the diesel and water were atomized simultaneously due to the separated injection channels without mixing problem. Therefore, compared to the 2-fluid nozzle, the 3-fluid nozzle is suitable for the stable operation of the fuel reformer. In case of the 3-fluid nozzle, Type A where the air was supplied through the central channel was the most efficient.

• 한국표면공학회지
• /
• 제49권2호
• /
• pp.172-177
• /
• 2016

In this paper, various electrochemical experiments were conducted in seawater solution to evaluate corrosion damage behavior of arc thermal sprayed Inconel 625 coating on SS400 steel in marine environment. As a result, corrosion damages of thermal sprayed Inconel 625 coating preferentially occurred at the defect area, and they were observed as a form of pitting corrosion in the galvanostatic experiments. In Tafel analysis, corrosion current density of Inconel 625 coating was relatively high due to influence of interconnected pores and Cr oxides in the thermal spray coating layer. On the other hand, the result of the potential measurement, thermal sprayed Inconel 625 coating should need the post-treatment which can compensate the defects like pores and cracks because Inconel 625 coating presented a higher potential of about 290 mV than that of the SS400 steel.

• 한국화재소방학회논문지
• /
• 제30권6호
• /
• pp.1-8
• /
• 2016

유가의 상승과 환경의 문제로 차량중량의 감소에 의한 차량연비를 개선하기 위하여 가연물인 플라스틱과 직물 등의 사용이 획기적으로 증대되어 주차장에서 화재가 발생하면 2000년대 중반 이전에는 한 두 대가 연소되고 마는 것과는 달리 주차된 차량 전체가 연소하는 화재가 많이 발생하였다. 본 연구에서 차량에 사용되는 플라스틱 등 가연물의 량을 확인한 결과 한 대에 316.2 kg으로 차량 전체무게 1935 kg 대비 16.34%가 되어 과거대비 10배 이상의 증가가 있었다. 또한 주차장의 소화설비로 스프링클러를 설치 시 물분무설비의 원래 성능대로 살수밀도를 $20lpm/m^2$를 사용할 것과 필로티 주차장에 호스릴이산화탄소소화설비 대신 적응성이 있는 포, 분말, 강화액 설비를 사용할 것을 요구하였다.

• 원예과학기술지
• /
• 제31권2호
• /
• pp.239-245
• /
• 2013

Occupational exposure and risk assessment were conducted to evaluate the safety of operators when insecticide acetamiprid was applied to apple orchard using a speed sprayer. Dermal patches, cotton gloves, socks, and masks were used to monitor the dermal exposure, and personal air pump with solid sorbent was used to measure the potential inhalation exposure. In validation to analytical methods, the limit of detection and limit of quantitation were 0.25 ng and 1 ng, respectively. Good reproducibility (coefficient variation < 4%), linearity (coefficient determination > 0.999), and recovery (85.3-118.2%) were obtained. Trapping efficiency of solid sorbent was 96.4% while breakthrough did not occur. Only hand exposure was measured on the gloves during mixing/loading to give $33-1,132{\mu}g$. Exposure amount of operator 3 among 4 workers was noticeably high. The total volumes of spray liquid for operators were $535-1,235mL{\cdot}h^{-1}$, corresponding to 0.03-0.08% of the applied spray solution. Highest contaminated parts of body were thighs, chest, and lower legs. The inhalation exposure ratio to the total application amount was significantly low. However, wind seemed to affect the inhalation exposure of operator. For risk assessment, margin of safety was calculated by the application of cloth and dermal penetration rate to obtain values of much larger than 1 in all cases. Therefore, health risk of operators during treatment of acetamiprid in apple orchard could be of least possibility.

• 한국응용곤충학회지
• /
• 제30권1호
• /
• pp.50-53
• /
• 1991

이화명나방 유충을 방제할 목적으로 이화명충이 가해한 벼 줄기에 곤충병원성선충인 Steinernema carpocapsae와 Heterorhabditis bacteriophora를 살포한 결과 효과가 좋았다. 8cm 길이의 벼 줄기 2본에 S. carpocapsae 250, 500, 1,000, 2,000마리/ml를 살포한 결과 68.6$\pm$10.0~94.9$\pm$2.6%의 치사율을 얻었으며 H. bacteriophora 100, 200, 400, 800마리 ml살포구에서는 91.4$\pm$0.7~100%의 방제를 얻었다. 그러나 3본의 벼줄기를 H.bacteriophora 현탁액에 침적한 경우는 100마리/ml 구에서는 42.6$\pm$4.7%, 200마리/ml구에서는 63.1$\pm$4.7%로 선충의 현탁액을 살포하는 것보다는 치사율이 낮아 효과가 적었다. 벼 줄기는 선충의 생존과 기주 탐색에 좋은 환경을 유지해 주어 곤충병원 성선충은 이화명충의 방제에 유용한 생물적 인자로 확인 되었다.

• 식물병연구
• /
• 제18권1호
• /
• pp.40-44
• /
• 2012

자두 검은점무늬병에 걸린 식물체로부터 순수분리된 X. arboricola pv. pruni 균을 NA배지에서 배양한 후 국내재배 핵과류에 분무접종한 결과 자두, 매실, 살구에 있어서는 과실에 뚜렷한 병원성을 나타내었으나 복숭아 과실은 저항성을 나타내었다. 특히 매실과 살구에서는 극심한 초기 과민성반응이 나타났는데 과실의 50% 정도가 생장 정지되어 낙과되는 현상을 보였으며 병반의 크기는 자두와는 달리 크게 진행되지 않고 많은 점무늬를 형성하는 병반형태를 나타내었고 복숭아에서는 과실병징이 나타나지 않았다. 접종된 여름철 신초가지에서 자두 포모사품종에서는 도관부까지 궤양조직이 형성되었으나 살구 그리고 매실에서는 체관부일부에서만 궤양조직이 형성되어 분리된 병원균은 자두 포모사품종에 특이적인 감염조직을 형성함을 알 수 있었다.