• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2662-2664
• /
• 1999

To improve the current waveform of diode rectifiers, we propose a new operating principle for the voltage diode rectifiers. In the conventional voltage rectifier circuit, relatively large capacitors are used to boost the output voltage, while the proposed circuit uses smaller ones and a small reactor not to boost the output voltage but improve the input current waveform. A circuit design method is shown and confirmed simulation. It explained that compared conventional SPWM inverter with HPWM(Half Pulse-width modulated)Inverter. Proposed HPWM inverter eliminated dead-time by lowering switching loss and holding over-shooting. Output voltage and current of this paper were applied for real air-conditioner.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 정기총회 및 추계학술대회 논문집 학회본부
• /
• pp.117-120
• /
• 1993

In this paper, a novel DC link voltage control scheme for a single-phase PWM converter is proposed. The main idea of the control scheme is eliminating the effect of dc link voltage harmonics by using power balance of input side and output side. With the proposed strategy, faster transient response than that of conventional method using low-pass filter can be obtained. In addition, a half period current control, based at equal switching frequency, is proposed. The validity of the proposed scheme is verified by simulation results for GTO PWM converter system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.464-469
• /
• 1998

In the conventional wire feeder drives of welding machine, one thyristor or MOSFET device was used for half-wave phase control circuit and direct EMF measurement was used for sensing the wire feed rate. But the method using one switching device has poor response for sudden disturbance and it has latent speed ripple. It can affect some welding performance such as spatter generation and irregular bead formming. Therefore, the welding performance using full-bridge PWM speed control scheme was compared with conventional driving scheme was compared with conventional driving scheme and experimented in this paper. The results of experiment confirm the posibility of welding performance improvement by proposed constant speed control scheme in wire feeding drive of welding machine.

• 한국수산과학회지
• /
• 제20권4호
• /
• pp.370-378
• /
• 1987

Wave reflection control functions of mound for the foundation of composite and perforated break-waters were investigated through the theoretical considerations. The theory developed is based on a simple summation of components of reflected waves. The applicability of the theory is assured by the comparative studies of the theoretical calculation and experimental data on the sea surface elevation in front of a breakwater. It is found that the reflection is mainly controlled by depth and width of the mound. In the design of composite type perforated breakwaters, the width of perforated part of the upright section can be decreased to less than half of the conventional design width for the same reflection by using the reflection control function of mound part and the reflection can be reduced until less than $30\%$ of that in the composite breakwaters. Using the results, a design method of mounds is proposed, by which the reduction of wave reflection is assured under the given wave conditions.

• 한국소음진동공학회논문집
• /
• 제19권3호
• /
• pp.294-300
• /
• 2009

In high speed railway bridges, dynamic analysis is important because of high passing velocity and moving load at the regular intervals, and damping ratio is a major parameter to predict dynamic responses. In this paper, damping ratios were estimated by using half power band width method and extended Kalman filter according to acceleration signal conditions, and a relationship between estimated damping ratios and representative values of bridge vibration was derived. From the results, damping ratios estimated from total ambient vibration were more reliable than only free vibration part. In case of using extended Kalman filter, the estimated damping ratios varying with RMQ(root mean quad), as one of representative values of bridge vibration, have more feasible trend. Thus, it is shown that further studies on reliabilities of estimated damping ratios are needed.

• Journal of the Optical Society of Korea
• /
• 제18권2호
• /
• pp.101-109
• /
• 2014

In this paper, four apodization functions are proposed for silicon-on-insulator (SOI) strip waveguides with sidewall-corrugated gratings. The effects of apodization functions on the full width at half maximum (FWHM), the side-lobe level, and the reflectivity of the reflection spectrum are studied using the coupled-mode theory (CMT) and the transfer-matrix method (TMM). The results show that applying proposed apodization functions creates very good filtering characteristics. Among investigated apodized waveguides, the apodization functions of Polynomial and z-power have the best performance in reducing side-lobes, where the side-lobe oscillations are entirely removed. Four functions are also used for precise adjustment of the bandwidth. Simulation results show that the minimum and maximum values of the FWHM are 0.74 nm and 8.48 nm respectively. In some investigated functions, changing the apodization parameters decreases the reflectivity which is compensated by increasing the grating length.

• 산업기술연구
• /
• 제23권A호
• /
• pp.35-39
• /
• 2003

There are many kinds of electronic ballast for various kinks of fluorescent lamps. The PFC(Power Factor Correction) circuit in electronic ballast is classified in two types. One is the active PFC and the other is the passive PFC circuit. The active type PFC is higher than the passive type, but the cost of the passive type is cheaper than the active type. In this study, we introduced the modified passive PFC method which is called semi-boost PFC, and then we analyzed and experimented the electronic ballast which is composed of the semi-boost PFC, half-bridge, and LCC resonant tank. Experimental results showed that the $$PF{\geq_-}0.98$$, $$CF{\leq_-}1.4$$ and input current $THD{\approx}15%$.

• Advanced Composite Materials
• /
• 제17권2호
• /
• pp.111-124
• /
• 2008

The effect of temperature on natural frequency and damping is investigated in two different composite materials, Kevlar 29 fiber woven and polyethylene cloth, used especially to design ballistic armor. A damping monitoring method is used experimentally to measure the frequency response curve and it is also modeled numerically using a finite element program. The natural frequencies of a material, or a system, are a function of its elastic properties, dimensions and mass. This concept is used to calculate theoretical vibration modes of the composites. The damping properties in terms of the damping factor are determined by the half-power bandwidth technique. Numerically analyzed and experimentally measured time response curves are compared. It is seen that polymer matrix composites have temperature dependent mechanical properties. This relationship is functional and they have different effects against temperature.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.190-191
• /
• 2007

Focused shock wave generation was tested under the water by the method of wire explosion. The wire was installed a focal point of the half ellipsoid, and the shock wave was focused on the other focal point. A numerous cavitations were observed in the path of the traveling shock wave and focal point by using high speed camera.

• 한국정보전자통신기술학회논문지
• /
• 제5권3호
• /
• pp.164-168
• /
• 2012

본 논문에서는 DVB-S2 표준안에서 권고되고 있는 irregular LDPC 부호의 고속화 방안에 대한 연구를 하였다. LDPC 복호기에서는 많은 반복횟수와 많은 연산량이 복호 속도 저하의 원인이 되고 있으며, 성능 저하 없이 반복횟수와 연산량을 감소하기 위해서 HSS 기반의 LDPC 복호 구조를 제시하였다. 결과 반복횟수를 성능 저하 없이 절반으로 줄일 수 있으며, 이를 효율적인 설계방안을 제시하였다. 결과 600Mbps급의 throughput을 갖는 LDPC 복호기를 구현 가능케 하였다.