• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.302-305
• /
• 2000

It is important to control the electron energy distribution to have high quality plasma process. A conventional inductively coupled plasma(ICP) source with 13.56MHz power is not adequate for low damage sub-half micron patterning process due to higher electron temperature. Only the pulsed plasma technique seems to provide low electron temperature, and thus low process damage. Recently, a novel method proposed by us, named as ‘Enhanced-ICP’, which uses periodic weak axial magnetic field added to a normal ICP source, has shown great improvement in etch characteristics. changes of plasma characteristics according to the frequency of time-varying axial magnetic field have been observed by probe-time-averaged Langmuir probe.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.301-302
• /
• 2016

Hold-up time 조건에 의해 넓은 입력전압 범위에서 설계되는 하프-브리지 LLC 컨버터는 높은 전압 이득을 얻기 위해 작은 자화 인덕턴스와 넓은 스위칭 주파수 범위가 요구된다. 하지만 이는 큰 1차측 도통손실 및 코어 손실을 초래한다. 본 논문에서는 하프-브리지 LLC 컨버터가 좁은 입력전압에서 설계되기 위한 새로운 hold-up time 보상 기법을 제안한다. 따라서 제안된 기법에서의 하프-브리지 LLC 컨버터는 큰 자화 인덕턴스 및 좁은 스위칭 주파수 범위로 설계 될 수 있다. 제안된 회로의 효과는 90-264Vrms 입력, 250-400V 링크 전압, 48V/480W 출력을 갖는 prototype의 실험을 통해 검증된다.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.487-489
• /
• 2004

As the electrodes are not needed, the electrodeless lamps using the induction discharge have a long lifetime and are robust against the variable output condition of a ballast. This paper proposed a dimmable resonant inverter for the electrodeless lamps. The proposed resonant inverter formed a half bridge inverter adopted FWM to control the average output power of the inverter and the illumination of a lamp. In this paper, the proposed dimming algorithm was described and the prototype experimental setup for 100W electrodeless lamps was carried out to verify the validity of the proposed dimming method.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.3
• /
• pp.182-186
• /
• 1995

SCM440, which is widely used as the diesel engine piston of vessel, has been hardened by a $CO_2$ laser with the wavelength of $10.6{\mu}m$. Laser hardening experiment has been carried out for the condition of a laser power 1kW, the travel speed between 0.4 and 1.5m/min, and a rectangular-Gaussian beam. Residual stress has been measured by using middle point technique of half value width of X-ray diffraction method. It was found that the compressive residual stress with the range between 400 and 600MHz has distributed in the laser hardening zones and the tensile residual stress between 100 and 200MHz has distributed in the boundary of hardening zones.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.360-363
• /
• 2000

A half bridge type double resonant high frequency resonant inverter using PFM is described. This proposed inverter can reduce distribution of the switching current because of using the current of the serial resonant circuit to the input current of the parallel one. In the case of variable capacitance of the DC voltage source separated capacitor the analysis of inverter circuit has generally described by using normalized parameter and operating characteristics has been evaluated in terms of switching frequency and parameters. Based on the characteristics value a method of the circuit design is proposed. The theoretical results are in good agreement with the experimental ones. In the future this proposed circuit is considerated to be useful for induction heating and discharge lamp.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.186-190
• /
• 2000

This paper propose a "Active common-mode voltage damper circuit" that capable of a suppression of a common-mode voltage produced in the PWM VSI. The four level half-bridge PWM inverter circuit and common-mode transformer are incorporated into the "Active common-mode voltage damper" the design method of which is presented Effect of "Active common-mode voltage damper" in this paper verifies a propriety and effectiveness in 2.2[kW] induction motor drive using IGBT inverter. Experimental results show that "common-mode voltage damper" makes contributions to reducing a high frequency leakage current and common-mode voltage.leakage current and common-mode voltage.

• Journal of the Korean Society of Industry Convergence
• /
• v.10 no.4
• /
• pp.227-233
• /
• 2007

In case of design of a rectifier to supply high current, To select switching frequency of semiconductor switches affect absolutely the design of the LC filter value in an power conversion circuit. The conventional rectifier by using MOSFET is no use in high current equipments because of small drain-source current. To solve this problem, this paper proposes to design of high capacity rectifier by parallel driving of MOSFET in the single half bridge DC-DC converter. This method can be able to develop high current rectifier by distributed drain-source current. The proposed scheme is able to expect a decrease in size, weight and cost of production by decreasing the LC filter value and increasing maximumly the switching frequency. The validity of the proposed parallel driving strategy is verified through computer-aided simulations and experimental results.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.10
• /
• pp.530-535
• /
• 2001

Resonant-type electronic ballast for a metal halide discharge(MHD) lamp is proposed and implemented for 400W MHD lamp. HID lamps have good color rendition, long life and good focusing capability but they have flickers by acoustic resonance when driven at high frequency. A new control method is employed to remove acoustic resonance related instability in HID lamp. By using the amplitude modulation, a spread spectrum effect is employed on the ballast. The control loop of resonant inverter is analyzed and a current is designed. The ballast consists of a power factor controller, an half-bridge resonant inverter, a simple ignitor and an integrator with OP-amps. The experimental results show the good performance as PF 0.93, ballast loss 22W at output 400W and the conducted EMI level is below 60dBuV.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1044-1048
• /
• 2001

This paper proposes a nonlinear impedance circuit composed by diodes and inductors or capacitors. This circuit needs no control circuits and switches, and the impedance value is changed by the polarity of current or voltage. This paper presents one of these applications to improve the input current of capacitor input diode rectifiers. The rectifier using the nonlinear impedance circuit id constructed with four diodes and four capacitors in addition to the conventional rectifiers, that is, it has eight diodes and five capacitors, including a DC link capacitor. It makes harmonic components of the input current reduce and the power factor improve. A circuit design method is shown by experimentation and confirmed simulation. It explained that compared conventional pulse-width modulated (PWM)inverter with half pulse-width modulated (HPWM) inverter proposed HPWM inverter eliminated dead-time by lowering switching loss and holding over-shooting.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.10a
• /
• pp.296-303
• /
• 2004

In this study, equivalent linear damping and stiffness of a single-degree-of-freedom (SDOF) structure with a rotational friction damper are estimated using the result of experiments and compared with those obtained from non-linear time history analyses. First, the transfer function of the test model is constructed and then the equivalent stiffness and damping are calculated, using the half-power bandwidth (HPB) method. For comparative study, those properties are estimated based on stochastic theory in the time domain. Both equivalent linear systems identified from experiments and numerical analyses correspond well. Further, it is observed that there exists an optimal clamping force on the rotational friction damper from estimated equivalent damping.