• Journal of Navigation and Port Research
• /
• v.28 no.4
• /
• pp.293-297
• /
• 2004

In this papers, an S-band oscillator of the low phase noise property using a miniaturized micro-strip hairpin shaped ring resonator is presented The substrate has a dielectric constant $\epsilon_\gamma$＝3.5, a thickness h＝0.508 mm, and loss tangent $tan\delta$＝0.002. A designed and fabricated oscillator shows low phase noise performance of 99. 71 dBc/Hz at 100 KHz offset frequency and of output power 19.584 dBm at center frequency 2.450 GHz. This circuit was fabricated with hybrid technique, but can be fully compatible with the MMIC due to its entirely planar structure.

• The Journal of Korean Institute of Information Technology
• /
• v.17 no.3
• /
• pp.43-50
• /
• 2019

In this paper, we propose a S-band oscillator with a reduced electrical size by applying a vertical split ring resonator(VSRR). The VSRR is a type of split ring resonator that operates as a resonator by the capacitance and inductance generated between the microstrip lines arranged on the top and bottom of the dielectric substrate and it has an advantage that the electrical size of the resonance circuit can be reduced as compared with the conventional ring resonator. In this paper, we design a VSRR operating over S-band and an oscillator using the VSRR as the resonant circuit. The proposed oscillator showed the output of 5.9dBm at 2.4HGz and showed the phase noise characteristics of -112.58dBc at 100KHz offset frequency and -117.85dBc at 1MHz offset.

• Journal of Advanced Navigation Technology
• /
• v.12 no.2
• /
• pp.122-131
• /
• 2008

In this paper, an S-band oscillator of the low phase noise property using miniaturized microstrip hairpin shaped ring resonator has been designed and implemented. The TACONIC's RF-35 substrate has a dielectric constant ${\varepsilon}_r$=3.5 a thickness h=20mil a copper thickness t=17 um and loss tangent $tan{\delta}$=0.0025. The designed and implemented 2.45 GHz oscillator shows low phase performance of -100.5 dBc/Hz a 100kHz offset. Output power 20.9 dBm at center frequency 2.45 GHz and harmonic suppression -32 dBc. The circuit was implemented with hybrid technique. But can be fully compatible with the RFIC's, MIC and MMIC due to its entirely planar structure.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.5
• /
• pp.931-936
• /
• 2018

We designed an x-band radar for motion detector using a frequency tunable hairpin ring resonator. The proposed doppler radar sensor can vary the oscillation frequency by applying a hairpin resonator using a varactor diode to the oscillator, and this can also reduce the size by transmitting and receiving a signal from Tx/Rx dual antenna. The fabricated doppler radar sensor was fabricated in $30{\times}24mm$, and it was confirmed that the pulse width difference occurred according to the distance from the object. The measurement results showed oscillation at 10.525GHz. We confirmed that it is enough to use as radar for motion detection from the measured results.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.446-452
• /
• 2020

In this paper, we propose a energy-saving LED module using K-band microwave motion detecting sensor. To oscillate K-band microwave signal, An oscillator using a hairpin-type microstrip resonator was designed to increase stability and make fabrication easier. To radiate the microwave signal, a two-channel(TX/RX) patch antenna arrays was developed. Wilkinson power divider and ring hybrid mixer were developed and applied to obtain Doppler shift from the received signal. Shield cans were installed to protect the stability of the signals and unwanted external noise. The proposed motion detection sensor was mounted on a demonstration LED module and the energy saving performance through pre-test was verified.