• Journal of Navigation and Port Research
• /
• v.31 no.9
• /
• pp.751-757
• /
• 2007

The authors aim to establish the theory necessary for developing free gyro positioning system and focus on measuring the nadir angle by using the motion rate of a free gyro. The azimuth of a gyro vector from the North can be given by using the property of the free gyro. The motion rate of the spin axis in the gyro frame is transformed into the platform frame and again into the NED (north-east-down) navigation frame. The nadir angle of a gyro vector is obtained by using the North components of the motion rate of the spin axis in the NED frame. The component has to be transformed into the horizontal component of the gyro by using the azimuth of the gyro vector and then has to be integrated over the sampling interval.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.177.2-177
• /
• 2001

The asynchronous gyro outputs in the 3-axis navigation system are defined as each of gyros has its own output frequency. In this case, the navigation system has gyro outputs concurrently with the sensor mechanical frequency instead of the attitude frequency. So, there is an asynchronous error between gyro outputs and attitude calculation. In this paper, we analyze the gyro output error caused by the asynchronous gyro and present the high speed sampling technique and the extrapolation and interpolation of gyro outputs for synchronizing the gyro outputs.

• Journal of KSNVE
• /
• v.5 no.3
• /
• pp.403-411
• /
• 1995

Square beam type piezoelectric vibrating gyro is developed for the measurement of angular velocity, which is compact, small in size and mass- producible. It features that three pieces of piezoelectric ceramics and bonded onto one face of equilateral square bar type gyro head. Two of them are used as sentuators which drive the gyro head and measure Coriolis force. The third piece is used for the feedback signal in order to resonate the gyro head and measure Coriolis force. The third piece is used for the feedback signal in order to resonate the gyro head with its fundamental natural frequency. Matching two fundamental natural frequencies in the gyro head with its driving frequency is found critical in the design of vibration gyro. Calibration results show that the vibrating gyro developed has the dynamic characteristics of first-order system within the frequency range of interest, which can be easily compensated by a lead compensator.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.5
• /
• pp.694-700
• /
• 2015

This paper deals with the design of 1-kW troidal type gyro. In general, gyro can be used as magnet bearing or flywheel energy storage device. The proposed troidal type gyro is used as a flywheel energy storage device. The gyro is capable of high-speed rotation in the air. The coriolis effect is taken into account when designing the rotor of the proposed gyro. Also the repulsive power of the permanent magnet is considered while selecting the shape and the thickness of the magnet. The neodymium is used as material of the magnets in this paper. The number of magnets are selected accordingly to reduce these torque ripples because torque ripples is an important factor while designing the gyro. The designed troidal type gyro is verified through the Finite Element Method (FEM).

• The Journal of Korea Robotics Society
• /
• v.15 no.3
• /
• pp.248-255
• /
• 2020

This paper introduces a Feedback Linearization (FL) controller to eliminate the gyro effect on a quadrotor UAV. In order to control the attitude of the quadrotor, the second model equation was differentiated to the 4-th order to induce the control input to be revealed, and then a new control input was derived based on the attitude transformation equation with a gyro effect. For the initial quick posture control of the quadrotor, the existing yaw control was replaced with a separate controller. The simulation was conducted with an experiment in which FL control to remove the gyro effect was applied to the quadrotor and an experiment without removing the gyro effect, from the experimental results, the maximum error seen in each axial direction of the quadrotor was x = 0.22 m, y = 0.20 m, z = 0.16 m. Through the proposed method, the effect of the FL controller for controlling the gyro effect of the quadrotor was confirmed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.264-267
• /
• 1991

In this paper, a new application method of the Kalman filter to desigin a gyro is proposed. The role of a gyro is the estimation of an input rate with minimal error covariance. The size of the error covariance depends on gyro's parameters, which makes it possible to use the parameters of gyro to minimze the estimation error covariance. Numerical analysis shows that the error covariance becomes smaller as the spin axis momentum becomes larger and the damping coefficient smaller, but production cost must be considered. Through numerical analysis the parameter set for an acceptable - performance gyro with small cost can be selected.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.149-150
• /
• 2007

By adding Gyro sensor to support the steering wheel angle sensor, an improved functional DR solution is proposed in this paper The proposed angle data algorism is developed based on the steering wheel with Gyro sensor for DR. The Gyro sensor support the error of steering wheel sensor to improve the angle data for the DR algorism.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.3
• /
• pp.368-377
• /
• 2009

In this paper we study the gyro bias calibration method of SDINS(Strap-Down Inertial Navigation System). Generally, SDINS's calibration is performed in 2-axis(or 3-axis) rate table with chamber for varying ambient temperature. We assumed that the majority of calibration-parameter except for gyro bias is knowned. During gyrobias calibration procedure, it can be induced some disturbances(accelerometer's short-term error induced rate table rotation and anti-vibration mount's rotation). In these cases, old gyro-bias calibration methods(using velocity error or attitude error) have an error, because these disturbances are not detectable at the same time. So that, we propose a new gyro-bias calibration method(heading error minimizing using equivalent linear transformation) that can detect anti-vibration mount's rotation. And we confirm efficiency of the new gyro-bias calibration method by simulation.

• Journal of Power System Engineering
• /
• v.19 no.3
• /
• pp.36-41
• /
• 2015

The true north-finding equipment utilizing gyro sensor is used for INS(Inertial Navigation System) and has an increasing preference for gyro compass system due to compact size, lightening, low power and price. The purpose of this experiment is to research gyro compass system providing high performance in the field of manned or unmanned gyro compass system which proposes the accuracy of 1% utilizing experimented equipment at true north of the earth. Unlike the conventional system, the proposed gyro sensor system indicates to be applied in the various and specific equipment using multiple technique and method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.30-30
• /
• 2000

In the three axis control of satellite by using reaction wheel and gyro, a Gyro carries out measuring of the attitude angie and the attitude angular velocity. The Gyro is operated by the electronic part and the mechanic actuator. The digital part of the electronic part is consisted of the FPGA (Field Programmable Gate Array), which is one of the methods for designing VLSI (Very Large Scale Integrated Circuit), and the mechanic actuator processes the input/output data by the dynamic model. In the research of the mixed mode of Gyro, the simulation is accomplished by SABER of the mixed mode simulator and the results for the practical implementation of the satellite ACS (Attitude Control System) interfaced with the data processing are proposed.