• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1453-1460
• /
• 2002

Creep-fatigue crack growth models have been proposed employing $(C_t)_{avg}$ as a crack tip parameter characterizing the time-dependent crack growth. The basic assumptions made in these previous models were ideal creep reversal conditions such as no creep reversal and complete creep reversal condition. Due to this assumption, the applicability of the models was limited since they did not consider partial creep reversal condition which is usually observed in many engineering metals at high temperature. In this paper the creep reversal parameter, Temperature;$C_R$, which was defined by Grover, is critically evaluated to quantity the extent of partial creep reversal at the crack tip. This approach does not rely on any simplifying assumptions regarding the extent of the amount of creep reversal during the unloading part of a trapezoidal fatigue cycles. It is shown that the $(C_t)_{avg}$ value calculated for 9Cr steel agrees well with the experimentally measured one. It is argued that the extent of improvement is not significant when the result is compared with that of the conventional model which has an assumption of full creep reversal behavior.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1997년도 Proceedings of the 13th KACG Technical Meeting `97 Industrial Crystallization Symposium(ICS)-Doosan Resort, Chunchon, October 30-31, 1997
• /
• pp.117-121
• /
• 1997

It is shown theoretically that uniform axial dopant concentration distribution can be made throughout the crystal by continuous Czochralski process. Numerical simulation are performed for the transient two-dimensional convection-diffusion model. A typical value of the growth and system parameters for Czochralski growth of p-type, 4 inches silicon crystal was used in the numerical calculations. Using this model with proper model parameter, the axial segregation in batchwise Czochralski growth can be described. It is studied by comparing with the experimental data. With this model parameter, the uniform axial concentration distribution of dopant is predicted in continuous Czochralski process.

• Journal of Welding and Joining
• /
• 제16권4호
• /
• pp.83-91
• /
• 1998

Cracking problems which high temperature plant components suffer during long-term service, occur very often at welded locations. The crack occurs due to accumulated creep damage near fusion line or at heat affected zone (HAZ). However, most of the studies on creep crack growth behavior have been performed with matrix metal not wit welded metal due to the difficulty of interpreting the test results. In this study, creep crack growth rates were measured with C(T) specimens whose cracks were formed along the fusion line or HAZ. The measured crack growth rates were characterized by {TEX}$C_{t}${/TEX}-parameter derived for elastic-primary-secondary creeping material. Since contribution of primary creep was significant for the tested 1Cr-0.5Mo steel, its effect was carefully studied. Effects of crack tip plasticity and material aging were also discussed.

• 대한기계학회논문집B
• /
• 제26권7호
• /
• pp.945-950
• /
• 2002

Shape optimization of a flow system is done to obtain the required effects, in the engineering fields. Most of these designs are accomplished by empirical or numerical analysis. In empirical analysis, it is difficult to obtain an optimal shape in the feasible design region. And, in numerical method, it usually needs much calculation expenses for shape optimization, because of design sensitivity analysis. In this study, we used the growth-strain method having only one distributed parameter such as a design variable. It optimizes a shape by making a distributed parameter such as dissipation energy uniform in a flow system, and then applied to two-flow systems. In order to overcome the stability occurred in numerical analysis performed by Azegami, the equation of volumic strain has been modified. Also, the shapes were compared with the known optimal shapes for the flow systems. Consequently, we confirm that the modified growth-strain method is very efficient and practical in shape optimization of the flow systems.

• Communications for Statistical Applications and Methods
• /
• 제3권1호
• /
• pp.235-242
• /
• 1996

When the linear growth birth and death process observed at a set of equidistant time points, McNeil and Weiss (1997) present a method for simultaneously estimating the Malthusian parameter and the sum of the two parameters under wery restricted assumptions using a diffusion approximation. This article suggests a method, which does not require the restrictions given by Weiss, for estimating simultaneously the Malthusian parameter and the sum of the two parameters.

• 한국해양공학회지
• /
• 제6권1호
• /
• pp.122-130
• /
• 1992

The effect of loading waveform on elevated temperature low-cycle fatigue crack growth behavior in a SUS 304 stainless steel have been investigated under symmetrical trangular (fast-fast), trapezoidal and asymmetrical(fast-slow, slow-fast) waveforms at 650.deg. C. It was found that the crack growth rate in fast-slow loading waveform appeared to be higher a little and the crack growth rate in slow-fast loading waveform much higer than that in fast-fast loading waveform, and difference in crack growth rate between fast-show and slow-fast waveforms nearly didn't appear in the region of da/dN>10/sup -2/ The crack growth rate in the trapezoidal loading waveform with t/sub h/=500sec appeared to be faster than that in slow(500sec)-fast(1sec). In addition, parameter modified J-integral could be considered as useful parameter for fatigue crack growth rate in all waveforms. The result obtained are as follow. da/dN=4.91*10/sup -3/ (.DELTA. J/sub c/)/sup 0.565/.

• 한국산림과학회지
• /
• 제87권1호
• /
• pp.40-49
• /
• 1998

본 연구는 보다 정확한 모수(母數) 추정을 통한 생장(生長)모델의 현실성을 향상시키는데 이용되는 생장 측정간격(임목의 측정 초기 연령 $T_1$과 재측정 연령 $T_2$의 기간)의 적합한 조합을 선택하기 위한 계획을 제공하는데 목적이 있다. 다양한 생장식을 데이터에 적용한 후 가장 적합한 것으로 판정된 생장식을 분석에 이용하였다. 여러 생장식을 분석한 결과 최적의 생장식으로 판명된 더미 변수를 포함하는 변형 Schumacher 방정식을 임분 흉고단면적(胸高斷面績) 생장식과 평균수고(平均樹高) 생장식을 얻기 위하여 이용하였다. 그리고 사용된 자료는 뉴질랜드 남섬 전역에서 측정된 업송(業松)(Pseudotsuga menziesii Mirb.Franco)의 생장 측정기간이 변형되지 않은 데이터와 모든 가능한 생장 측정기간을 포함하는 변형된 2종류의 데이터이었다. 단기의 측정기간에서부터 장기의 측정기간의 범위를 포함하는 데이터(모든 가능한 생장 측정기간을 포함하는 데이터)를 사용할 때 흉고단면적 생장식과 임분 평균수고 생장식에서 모수 추정의 정확성이 증가되는 것이 발견되었다.

• 한국어류학회지
• /
• 제20권2호
• /
• pp.81-89
• /
• 2008

메기, Silurus asotus에서 포식과 기아가 생존과 성장, 내장괴지수, 간중량지수, 생식소중량지수, 외형계측형질 변화 및 혈액 parameter들에 미치는 영향을 파악하기 위해 80일동안 기아 실험을 수행하였다. 기아군의 생존과 성장은 포식군의 생존과 성장에 비해 낮았다(P<0.05). 기아는 체중성장률, 일간성장률과 비만도에서 성장 정지 효과를 나타낸 반면, 포식군은 지속적인 성장을 보였다. 외형 계측형질 중복강 부위 횡단길이 관련에서 포식군은 실험 시작시와 차이를 보이지 않았으나, 기아군은 차이를 나타냈다 (P<0.05). 실험 기간 중 혈액성상(cortisol, glucose, AST, ALT, RBC 및 hemoglobin)에서 포식군과 기아군 사이에 유의한 차이를 보였다. 본 연구 결과, 포식과 기아 파악에 사용된 모든 parameter들은 본 종의 영양 상태 확인의 지표로 유용하며, 양식 메기의 성장 시기 평가 결정에 유용하리라 사료된다.

• Management Science and Financial Engineering
• /
• 제14권2호
• /
• pp.89-104
• /
• 2008

Growth curves including Bass, Logistic and Gompertz functions are widely used in forecasting the market demand. Nonlinear least square method is often adopted for estimating the model parameters but it is difficult to set up the starting value for each parameter. If a wrong starting point is selected, the result may lead to erroneous forecasts. This paper proposes a method of selecting starting values for model parameters in estimating some growth curves by nonlinear least square method through grid search and transformation into linear regression model. Resealing the market data using the national economic index makes it possible to figure out the range of parameters and to utilize the grid search method. Application to some real data is also included, where the performance of our method is demonstrated.

• 품질경영학회지
• /
• 제26권3호
• /
• pp.130-140
• /
• 1998

Studies present a guide to parameter estimation of software reliability models using SAS JMP. In this paper, we consider only software reliability growth model(SRGM), where mean value function has a S-shaped growth curve, such as Yamada et al. model, and ohba inflection model. Besides these stochastic SRGM, deterministic SRGM's, by fitting Logistic and Gompertz growth curve, have been widely used to estimate the error content of software systems. Introductions or guide lines of JMP are concerned. Estimation of parameters of Yamada et al. model and Logistic model is accomplished by using JMP. The differences between Yamada et al. model and Logistic model is accomplished by using JMP. The differences between Yamada et al. model and Logistic model is discussed, along with the variability in the estimates or error sum of squares. This paper have shown that JMP can be an effective tool I these research.