• 콘크리트학회논문집
• /
• 제16권5호
• /
• pp.635-643
• /
• 2004

본 연구에서는 그라우트 충전식 철근이음의 보다 합리적인 설계를 위한 자료를 제공하기 위하여 그동안 개발되어 사용되고 있는 각종 그라우트 충전식 철근이음의 구조성능을 비교 분석하고자 국내뿐만 아니라 외국에서 실시했던 각종 그라우트 충전식철근이음의 320여개 실험결과를 수집한 후에 철근이음의 내력을 중심으로 비교 분석하여 다음과 같은 결론을 얻었다. 첫째, 그라우트 충전식 철근이음의 내력은 철근의 정착길이와 충전 그라우트 압축강도가 증가함에 따라서 커지는 경향을 보여주었다. 특히 이러한 경향은 상대적으로 철근의 정착길이가 짧거나 충전 그라우트 압축강도가 낮아서 부착파괴가 발생한 실험체에서 뚜렷하게 나타났다. 둘째, 슬리브의 형상이 그라우트 충전식 철근이음의 부착강도에 영향을 미치는 것으로 나타났다. 셋째, 부착파괴된 철근이음 실험체에서 철근의 직경에 따른 철근이음 내력의 차이가 특별하게 나타나지 않았다. 넷째, 충전 그라우트 충전식 철근이음에서 철근 항복강도의 $125\%$ 이상의 인장력을 전달하여 ACI 및 국내 규준을 만족하기 위해서는 그라우트 압축강도가 70MPa이면 철근의 정착길이를 4.5d 이상, 그라우트 압축강도가 80MPa이면 철근의 정착길이를 3.9d 이상 확보해야 한다. 또한, 철근 인장강도 이상의 인장력을 전달하여 AIJ 규준을 만족하기 위해서는 충전 그라우트 압축강도가 70MPa이면 철근의 정착길이를 5.34 이상, 그라우트 압축강도가 80MPa이면 철근의 정착길이를 4.7d 이상 확보해야 한다.

• Computers and Concrete
• /
• 제31권6호
• /
• pp.545-559
• /
• 2023

In this study, an experimental investigation was conducted to assess the influence of ground granulated blast furnace slag (GGBS) and silica fume (SF) on the fresh and hardened properties of grout specimens and preplaced aggregate concrete (PAC). Grout proportions were optimized statistically using a factorial design and were applied to 10 mm and 20 mm coarse aggregates to produce PAC. The results demonstrate that GGBS has a more significant effect on the compressive strength of grout compared to SF, with a small increase or decrease in the GGBS content having a greater influence on the compressive strength of grout than SF. The water to binder ratio had the most significant effect on the compressive strength of PAC, followed by the coarse aggregate size and sand to binder ratio. An empirical relationship to predict the compressive strength of PAC was proposed through an experimentally derived factorial design along with a statistical analysis of collectively obtained data and a deep literature review. The results predicted by the empirical relationship were in good agreement with those of PAC produced for verification.

• Geomechanics and Engineering
• /
• 제33권4호
• /
• pp.327-339
• /
• 2023

The expansion capacity and strength of expansive grout have a significant influence on the stress state of a supported rock mass and the strength of a grout-rock mass structure. The expansion and strength characteristics are vital in grouting preparation and application. To analyze the expansion performance and mechanical properties of expansive grout, uniaxial compressive strength (UCS) tests, expansion ratio tests, XRD, SEM, and microscopic scanning tests (MSTs) of expansive grout under different curing pressure conditions were conducted. The microevolution was analyzed by combining the failure characteristics, XRD patterns, SEM images, and surface morphologies of the specimens. The experimental results show that: (1) The final expansion ratio of the expansive grout was linear with increasing expansion agent content and nonlinear with increasing curing pressure. (2) The strength of the expansive grout was positively correlated with curing pressure and negatively correlated with expansion agent content. (3) The expansion of expansive grout was related mainly to the development of calcium hydroxide (Ca(OH)2) crystals. With an increase in expansion agent content, the final expansion ratio increased, but the expansion rate decreased. With an increase in the curing pressure, the grout expansion effect decreased significantly. (4) The proportion of the concave surfaces at the centre of the specimen cross-section reflected the specimen's porosity to a certain extent, which was linear with increasing expansion agent content and curing pressure.

• 한국안전학회지
• /
• 제26권5호
• /
• pp.59-64
• /
• 2011

This paper presents the research results performed to develope the shrinkage-free grout with high early strength. Alumina cement and anhydrite were utilized as the expensive tool to gain the shrinkage-free grout. The compressive strength, length change, and ettringite formation of the grout were investigated with compressive test, length change test, and X-ray diffraction. The more anhydrite was added into the grout, the larger the early expansion of the grout. In addition, the more anhydrite formated the more ettringite. From this study, It was conformed that the grout mixture with shrinkage-free property and high early strength is the mixture with the ratio of alumina cement and anhydrite of 40:60 by weight.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.597-602
• /
• 1997

The compressive strength of horizontal joints in precast concrete large panel structures depends on parameters such as grout and panel strength, detail of joint, joint moment, width of grout column etc. As the panels are only connected at the pocket, it results in the reduction of compressive strength area. The purposes of this study are to develop the suitable grout material the joint pocket and to enable us to evaluate structural capacity. The validity of the design formulas provides us more economic system in construction. Test results of 15 specimens show that the proper construction procedure and grouting material develop the sufficient compressive strength of the wall as monolithic system.

• Geomechanics and Engineering
• /
• 제19권4호
• /
• pp.361-368
• /
• 2019

This study aims to evaluate the applicability of a grout material that is mixed with carbon fiber, biogrout, ground granulated blast furnace slag (GGBS) powder and cement. Uniaxial compressive strength tests were performed on homo-gel samples at days of 1, 3, 7, 14 and 28. In addition, the variation of permeability with the mixing ratios was measured. Based on the uniaxial compressive strength test, it was confirmed that the uniaxial compressive strength increased by 1.2times when carbon fiber increased by 1%. In addition, as a result of the permeability test, it was found that when the GGBS increased by 20%, the permeability coefficient decreased by about 1.5times. Therefore, the developed grout material can be used as a cutoff grouting material in the field due to its strength and cut-off effect.

• 콘크리트학회지
• /
• 제6권2호
• /
• pp.138-147
• /
• 1994

대형 콘크리트 판넬구조 수평접합부는 상부로부터 전달되는 축하중에 대하여 저항하게 되며 이때의 저항내력은 그라우트와 판넬의 강도, 접합부의 형태 및 단부 모멘트, 그라우트의 폭 등에 따라 변하게 된다. 본 연구는 패쇄형 수평접합부에 대한 실험연구로서 슬래브의 단부형태, 벽판넬의 단부보강 및 슬래브의 횡변위 구속에 따른 내력의 변화를 관찰하고자 하였다. 현재 대형 콘크리트 패널구조 수평접합부의 설계에 적용되고 있는 국내 규준식은 국내의 대형 콘크리트 패널구조와는 다소 다른 형태의 실험결과에 의해 유도된 식으로서 그 적용성에 대한 평가가 요망된다. 따라서 본 연구에서는 실험결과를 근거로 이에 대한 평가를 실시할 뿐만 아니라 폐쇄형 수평접합부의 내력을 평가할 수 있는 적합한 이론식을 제시 하였다. 실험결과, 상부 벽판넬의 단면이 결손(10mm)됨에 따라 약 23.5% 내력이 저감되는 것으로 나타났으며, 슬래브 단부형태의 따른 차이와 벽판넬의 단부보강에 따른 내력의 차이, 슬래브의 횡변위 구속 유무에 따른 내력의 차이는 거의 없는 것으로 나타났다. 또한, 제안되 이론식과 실험결과를 비교한 결과 이론식에 의한 결과가 실험결과와 좋은 대응을 보이는 것으로 나타났다.

• 한국지반공학회논문집
• /
• 제15권1호
• /
• pp.63-78
• /
• 1999

압축형 앵커의 설계를 위해서는 세가지의 조건이 고려되어져야 한다. 그 첫째가 주면마찰저항력이고, 둘째가 강선의 인장강도이고, 셋째가 그라우트의 압축강도이다. 특히, 세가지 조건 중에서도 그라우트의 압축강도는 압축형 앵커의 인발력 산정에 있어서 가장 중요한 매개변수가 된다. 압축형 앵커가 지중에서 인발될 때, 그라우트의 압축강도는 지반 구속압에 의해 증가하게 된다. 이 지반 구속압은 정지 토압에 의한 구속압과 "포아송 효과"라고 부르는 횡방향 팽창에 의해 증가되는 구속압으로 이루어져 있다. 본 논문에서는 압축형 앵커인 SSC 앵커의 내하체 압축시험을 통해 앵커 설계법을 제안하고, 이 설계법을 사용하여 앵커의 인발저항력을 계산하는 컴퓨터 프로그램을 개발하였다.그램을 개발하였다.

• Geomechanics and Engineering
• /
• 제33권2호
• /
• pp.211-219
• /
• 2023

This study analyzes the changes in the physical properties of grout by irradiating it with ultrasonic energy and assesses the injectability of the grout into deep rock fractures. The materials used in the research are OPC (Ordinary Portland Cement) and MC (Micro Cement), and are irradiated depending on the water/cement ratio. After irradiating the grout with ultrasonic energy, viscosity, compressive strength, and particle size are analyzed, and the results of the particle size analysis were applied to Nick Barton's theory to evaluate the injectability of the grout into deep rock fractures under those conditions. It was found that the viscosity of the grout decreased after ultrasonic wave irradiation, and the rate of viscosity reduction tended to decrease as the water/cement ratio increased. Additionally, an increase in compressive strength and a decrease in particle size were observed, indicating that the grout irradiated with ultrasonic energy was more effective for injection into rock fractures.

• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.509-513
• /
• 2018

This study uses fly ash for non-shrinkage grout in order to develop strength of grout and improve its durability. We grind fly ash to the extent of $7,000cm^2/g$ and use ground fly ash and raw fly ash respectively at the proportion of 10%, 20%, 30% instead of OPC and compare the results drawn on the condition of each proportion. As a mixed material of grout, EVA and water-reducing agent is added in order to prevent bleeding and improve segregation resistance, CSA is added with a view to preventing drying shrinkage and improving early strength property. In regard to flow and flow time test for analyzing and evaluating workability, it is revealed that grouts of all mix proportions except raw fly ash 30% mix proportion satisfy all performance criteria. With regard to length change rate, grout with no admixture shows the highest shrinkage rate, but the rate is 0.0005%, extremely insignificant rate. As material age increases, compressive strength of two grouts, that is to say ground fly ash 10% and 20%-used grouts, exceed that of grout with no admixture or show high-level compressive strength.