• Journal of the Korea Institute of Building Construction
• /
• v.2 no.2
• /
• pp.129-134
• /
• 2002

The strength and durability of concrete are affected by various factors such as the quality of material, mixing ratio, construction, the method of cure, time elapsed. the condition of test and etc., it is very difficult to pre-estimate the strength of concrete with the use of experimental specimen. The domestic standard of specimen cylindrical type and its sizes are both l0cm$\times$20cm and 15cm$\times$30cm, which are prescribed in KS F2405, and the loading speed is prescribed to test with 2~3kgf/$\textrm{cm}^2$ per second. The loading speed should have great effect on the compressive strength, but in reality in the construction site sometimes the loading speed is applied so dubiously that the value of the compressive strength can be unreliable. And the cross sectional area of a specimen should be level and smooth, otherwise it can be broken at a lower stress than the real strength through the eccentric or intensive working of the load. Capping should be carried out in order to measure the strength correctly. And used for capping are various materials such as capping compound, cement glue, plaster, mechanical grinding and etc. In this study, therefore, I have carried out an experiment on the relationship among the loading speed, the ratio of height to diameter of specimen, the method of capping, and the compressive strength, for the efficient quality control of concrete structures. So this study has been purposed to provide some basic data that can be used effectively at construction sites.

• Journal of Welding and Joining
• /
• v.34 no.1
• /
• pp.41-46
• /
• 2016

With the recent increase in size of ships and offshore structures, there are more demand for thicker plates. As the thickness increases, it is known that fatigue life of the structures decrease. To improve the fatigue life, post weld treatments techniques, such as toe grinding, TIG dressing and hammer peening, are typically employed. However, these techniques require additional construction time and production cost. Therefore, it is of crucial interest steels with longer fatigue crack growth life compared to conventional steels. This study investigates fatigue crack growth rate (FCGR) behaviours of conventional EH36 steel and Ferrite-Bainite dual phase EH36 steel (F-B steel). F-B steel is known to have improved fatigue performance associated with the existence of two different phases. Ferrite-Bainite dual phase microstructures are obtained by special thermo mechanical control process (TMCP). FCGR behaviours are investigated by a series of constant stress-controlled FCGR tests. Considering all test conditions (ambient, low temperature, high stress ratio), it is shown that FCGR of F-B steel is slower than that of conventional EH36 steel. From the tensile tests and impact tests, F-B steel exhibits higher values of strength and impact energy leading to slower FCGR.

• Korean Journal of Construction Engineering and Management
• /
• v.7 no.6
• /
• pp.79-89
• /
• 2006

Current removing process is labor intensive and time consuming, employing a conventional grinding type manual machine. From a social and economic point of views, these kinds of manual tasks bring about social inconvenience and economic loss including traffic jam and high labor costs. The objective of the study was to develop and evaluate a road stripe removal equipment using water jet technology. The following shows the results. First, It was analyzed that the obtainable productivity from the equipment developed in the study is 280% compared to the current equipment. In this study, it was also calculated the Benefit/Cost Ratio and the result showed that the ratio is 3.28, so it is expected that the equipment can produce great benefits for the relevant companies. Second, an analysis was also conducted on the traffic congestion cost, and the equipment could save about \2,550 million per day compared to the conventional equipment. Therefore, it is analyzed that the economic viability of the equipment is sufficient.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.23 no.2
• /
• pp.41-49
• /
• 2013

Objectives: The purpose of this study was to clarify the association between serum carcinoembryonic antigen (CEA) and type of work in the shipbuilding industry. Methods: 1,072 final study subjects were admitted to a general hospital from April through July 2010 for the purpose of medical examination. Data on general characteristics such as age, smoking history, alcohol history and exercise habits was gathered through structured self-administered questionnaires. Information on job factors was collected from a medical examination, by interview and through company personnel data. Serum CEA levels were measured after eight hours' fasting and were analyzed by a radioimmunoassay. Results: On univariate analysis, the mean serum CEA level was significantly higher among married (p=0.02), older age (p<0.01), longer work time (p<0.01), smokers (p<0.01), lower education (p<0.01), and indirect and direct exposure groups (p<0.01). On multiple regression analysis, serum CEA level was influenced by smoking (p=0.001), duration of work (p=0.019), and direct exposure group (p<0.001). However, among the direct exposure group, serum CEA level was not significantly different between welding, mounting, electro-device constructive work, grinding and cleaning, and painting. Conclusions: The goal of this research was to determine if there were differences between serum CEA levels according to occupational role among shipyard workers. The direct exposure group of shipyard workers had a relatively higher level of serum CEA than did the indirect exposure group and office workers, most likely due to occupational exposure.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.1
• /
• pp.35-43
• /
• 2015

A large amount of radioactively-contaminated gravel can be produced on the demolition/restoration of facilities related the back end of fuel cycle. However, because of the lacking in basic knowledge for decontamination of radioactive-contami-nated gravel, this study has performed the basic tests using for soil-washing. To find effective decontamination condition, several experiments were carried out for the selection of optimal decontamination agents. Washing by 0.1 M nitric acid was proved to be more effective than that by distilled water or surfactant for decontamination of uranium-contaminated gravel. In addition, crushing/grinding of uranium-contaminated gravel prior to washing was contributed to increase in of removal efficiency of uranium and reduction of decontamination time. The smaller the sizes of crushed gravel was, the more the removal efficiency increased. Also, small the sized particles improved chances for meeting the clearance requirement of the treated gravel.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.2
• /
• pp.103-103
• /
• 2014

Manufacturing of lens and mirror using Diamond Turning Machine (DTM) offers distinct advantages including short fabrication time and low cost as compared to grinding or polishing process. However, the DTM process can leave mid-frequency error in the optical surface which generates an undesirable diffraction effect and stray light. The mid-frequency error is expected to be eliminated by mechanical polishing after the DTM process, but polishing of soft surface of ductile aluminum is extremely difficult because the polishing process inevitably degrades the surface form accuracy. In order to increase its surface hardness, we performed electroless nickel plating on the surface of diamond-turned aluminum (Al-6061T6) off-axis mirrors, which was followed by the 6-hour-long baking process at $200^{\circ}C$ for improving its hardness. Then we polished the nickel plated off-axis mirrors to remove the mid-frequency error and measured polished mirror surfaces using the optical surface profilometer (NT 2000, Wyko Inc.). Finally, we ascertained that the mid-frequency error on the mirror surface was successfully removed. During the whole processes of nickel plating and polishing, we monitored the form accuracy using the ultra-high accurate 3-D profilometer (UA3P, Panasonic Corp.) to maintain it within the allowable tolerance range (< tens of nm). The polished off-axis mirror was optically tested using a visible laser source and a pinhole, and the airy pattern obtained from the polished mirror was compared with the unpolished case to check the influence of mid-frequency error on optical images.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.6
• /
• pp.60-64
• /
• 2002

This paper describes the machining characteristics of the MoSi$_2$--based composites through the process of electric discharge drilling with various tubular electrodes. In addition to hardness characteristics, microstructures of Nb/MoSi$_2$laminate composites were evaluated from the variation of fabricating conditions, such as preparation temperature, applied pressure, and pressure holding time. MoSi$_2$-based composites have been developed in new materials for jet engines of supersonic-speed airplanes and gas turbines for high-temperature generators. These high performance engines may require new hard materials with high strength and high temperature-resistance. Also, with the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material. The tool electrode is almost -unloaded, because there is n direct contact between the tool electrode and the work piece. By combining a non-conducting ceramic with more conducting ceramic, it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and MoSi$_2$ powder was an excellent strategy to improve hardness characteristics of monolithic MoSi$_2$. However, interfacial reaction products, like (Nb, Mo)SiO$_2$and Nb$_2$Si$_3$formed at the interface of Nb/MoSi$_2$, and increased with fabricating temperature. MoSi$_2$composites, with which a hole drilling was not possible through the conventional machining process, enhanced the capacity of ED-drilling by adding MbSi$_2$, relative to that of SiC or ZrO$_2$reinforcements.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.8 no.1
• /
• pp.24-35
• /
• 1998

Cumulative trauma disorders(CTDs) have been a growing problems for US and European industries with higher incidence rate every year. The increase and their associated costs has led companies to form committes and implement programs to address this problem. In our country, we have just started to recognize and to work on the problems in industry. This study conducted an ergonomic analysis for typical jobs of ship building industry which was not usually surveyed for CTD problem. A baseline CTD checklist which was supposed to do a risk assessment was developed and applied in this study. Initially, we considered five major parts in the checklist which consisted of personal, frequency, posture, force, and miscellaneous information. Most jobs in ship building industry were much different from typical assembly work and VDT work that have been major part of the previous CTD studies. Specifically, job characteristics in terms of frequency and posture were quite different. There were relatively long cycle time, awkward postures for whole body (not just for upper extremities). Also, CTD risk scores based on checklist were a lot higher than the scores for VDT jobs which was a case of preceding application of the checklist. Specifically, grinding jobs turned out to be the most risky one in terms of CTDs. In conclusion, usual CTD prevention guidelines are not likely to he effective in this type of industry. An individual job based interventions are strongly suggested to have a good control of CTD problems in ship building industry.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.5
• /
• pp.643-648
• /
• 2005

Near infrared reflectance spectroscopy (NIRS) has become increasingly used as a rapid, accurate method of evaluating some chemical constituents in cereal grains and forages. If samples could be analyzed without drying and grinding, then sample preparation time and costs may be reduced. This study was conducted to develop robust NIRS equations to predict fermentation quality of corn (Zea mays) silage and to select acceptable sample preparation methods for prediction of fermentation products in corn silage by NIRS. Prior to analysis, samples (n = 112) were either oven-dried and ground (OD), frozen in liquid nitrogen and ground (LN) and intact fresh (IF). Samples were scanned from 400 to 2,500 nm with an NIRS 6,500 monochromator. The samples were divided into calibration and validation sets. The spectral data were regressed on a range of dry matter (DM), pH and short chain organic acids using modified multivariate partial least squares (MPLS) analysis that used first and second order derivatives. All chemical analyses were conducted with fresh samples. From these treatments, calibration equations were developed successfully for concentrations of all constituents except butyric acid. Prediction accuracy, represented by standard error of prediction (SEP) and $R^2_{v}$ (variance accounted for in validation set), was slightly better with the LN treatment ($R^2$ 0.75-0.90) than for OD ($R^2$ 0.43-0.81) or IF ($R^2$ 0.62-0.79) treatments. Fermentation characteristics could be successfully predicted by NIRS analysis either with dry or fresh silage. Although statistical results for the OD and IF treatments were the lower than those of LN treatment, intact fresh (IF) treatment may be acceptable when processing is costly or when possible component alterations are expected.

• Journal of Korean Medical classics
• /
• v.26 no.1
• /
• pp.99-129
• /
• 2013

Objective : Most disease of the aged comprise chronic illness, hence the diet is important. Yet, the study on diet methodology for the remedy of the aged folks' aliments is scarce. The diet for the aged must be easy to digest- in regard to the physiological features of the aged, delightfully chewable, while meeting the expectation and guaranteeing nutrition-supply and remedial efficacy. Material and Method : This study is designed to accomplish following things with the Yang-lo-bong-chin-seo, a text on maintaining and upbringing the health for the aged: (1) classify the food recorded in the text in terms of cooking methods, (2) then sort the main ingredients in remedial herbal rice porridge(Yak-sun-jook) in food material science manner, (3) evaluate the cooking methods of the porridge for each and various symptoms, and (4) assess the features of each ingredient of the porridge, the value of it both in oriental medicine's and nutrition's scope. Results : 1) Among 64 main dishes recorded in Yang-lo-bong-chin-seo, rice porridge composes the majority, which is 64%. Stew and soup account for 60% of side dishes. 2) In 15 food cures, 43 remedial herbal rice porridges(Yak-sun-jook) were recorded. 3) Yak-sun-jook utilizes most chinese herbs as its food material. 4) Yak-sun-jook is made more with vegetable ingredients than animal ingredients and consist highly of chinese herbs. 5) Main ingredients in the porridges are effective in disease cure in addition to sufficient, well-balanced nutrition. 6) Cooking method of the porridge is grinding chinese herbs into powder or boiling them for a long time. Conclusion: All forementioned steps build the informational foundation - for this purpose the information be utilized - for making possible the development and the devising of pragmatic and feasible Remedial herbal rice porridge(Yak-sun-jook).