• 한국식품과학회지
• /
• 제34권5호
• /
• pp.931-934
• /
• 2002

폐기화 되고 있는 포도씨를 대체 식용유지 자원으로 개발하고자 포도씨에 함유되어 있는 기름의 최적 추출 방법을 확립하고자 실시하였다. Campbell early 포도씨의 일반 성분 분석 결과 압착 법으로 추출한 기름의 수율은 분쇄 후 볶아 증숙한 처리구, 분쇄 후 볶음 처리구, 분쇄 후 증숙 처리구순이었고 볶음 후 분쇄 처리구에서 가장 낮은 수율을 나타내었다. 용매 추출에 의한 수율은 정치 추출하였을 때 ether 처리구가 24시간 77.4%, 48시간 80.9%로 가장 높았고, 그 다음이 methanol과 n-hexane으로 나타났다. 포도씨 기름의 추출수율을 높이기 위한 방법으로 여러 가지 처리를 조합하여 실시한 결과 다음과 같은 순으로 방법이 확립되었다. (1) 수분 $10{\sim}12%$의 포도씨를 $95{\sim}100^{\circ}C$에서 20분 정도 볶음 처리하고 30분간 실온으로 방냉한다. (2) 분쇄기로 1차 $1{\sim}2\;mm$ 정도 입자로 하여 2차 분쇄로 0.5 mm 이하 입자크기로 분쇄한다. (3) 분쇄된 씨를 steam boiler에서 $0.8{\sim}0.9\;kg{\cdot}f/cm^2$의 압력으로 10분 정도 증숙 시킨 후 열 교환 장치가 부착된 압착 추출기에 $6{\sim}\;8kg$ 정도 넣어 추출한다. (4) 이때의 압착력은 $400\;kg/cm^2$에서 $2{\sim}3$분, $550{\sim}600\;kg/cm^2$에서 10분 그리고 $700\;kg/cm^2$에서 기름 흔적이 없어 질 때까지 추출한다. 추출 방법을 달리하여 추출한다. 추출 방법을 달리하여 추출한 포도씨 기름에 대한 관능검사를 실시한 결과, 최적조건으로 추출한 기름이 맛, 향기 및 색깔에서 가장 좋은 것으로 나타났고 그 다음이 분쇄 후 볶아 추출한 기름이 좋게 나타났으며 분쇄 후 볶아 증숙하여 압착한 기름순으로 나타났다.

• 한국세라믹학회지
• /
• 제46권1호
• /
• pp.102-107
• /
• 2009

This study has been focused on an effective surface finishing method combining ELID (ELectrolytic In-process Dressing) and MAP (Magnetic Assisted Polishing) for the nano-precision mirror grinding of glass-lens molding mould. ELID grinding is an excellent technique for mirror grinding of various advanced metallic or nonmetallic materials. A polishing process is also required for elimination of scratches present on ELID grinded surfaces. MAP has been used as polishing method due to its high polishing efficiency and superior surface quality. It also presents some techniques for achieving the nanometer roughness of the hard material such as WC-Co, which are extensively used in precision tooling material.

• 한국공작기계학회논문집
• /
• 제13권3호
• /
• pp.24-29
• /
• 2004

The grinding process plays a key role which decides the quality of a product finally. But the grinding process is very irregular, so it is very difficult to analyse the process accurately. Therefore it is very important in the aspect of precision and automation to reduce the idle time and to decide the proper dressing time by watching. In this study, we choose the method which can be observed directly by using of computer vision and then apply pattern classification technique to the method of measuring the wheel surface. Pattern classification technique is proper to analyse complicated surface image. We observe the change of the wheel surface by using of the gray level run lengths which are representative in this technique.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.97-104
• /
• 2006

ELID(Electrolytic In-process Dressing) grinding is an excellent technique for mirror grinding of various advanced metallic or nonmetallic materials. A polishing process is also required for elimination of scratches present on ELID grinded surfaces. MAP(Magnetic Assisted Polishing) has been used as polishing method due to its high polishing efficiency and to its resulting in a superior surface quality. This study is describing an effective fabrication method combining ELID and MAP of nano-precision mirror grinding for glass-lens molding mould. It also presents some techniques for achieving the nanometer roughness of the hard metals, such as WC-Co, which are extensively used in precision tooling material.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.322-325
• /
• 2000

In the previous report1), the grinding characteristics of quartz were investigated. In this paper, the grinding mechanisms of brittle materials including ceramics and quartz are modeled and a new parameter SDR(Surface roughness Direction Ratio) is proposed to characterize the grinding mechanisms of such materials. A set of experiments were performed to verify the effectiveness of the suggested parameter. The experimental results indicate that the plastic deformation is the dominant material removal mode at the grinding conditions which show the higher value of SDR. In the case of quartz, the material was removed by brittle fracture in a lower value of SDR and by plastic deformation in a higher value of it. SDR is not affected by wheel mesh size when brittle fracture occured. But in the plastic deformation case, SDR value increases with wheel mesh size.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.309-314
• /
• 2001

The balance of high speed spindle system with high precision rotation like grinding machine is very important. Traditionally, we use trial and error method to balance the spindle. It takes much time. So we are developing the automatic balancing equipment being used in the grinding machine. The balancing head we develop is wireless. It will be used high-speed grinding machine. We use influence coefficient method to control the automatic balancer. Experiments are based on automatic and manual balancing. We perform test of the vibration filter. It helps to remove noise. The filter and experiments with automatic balancing controller show that automatic balancing control can be successfully achieved with the quick response and good stability characteristics.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.447-452
• /
• 2000

The grinding plays a key role which decide the quality of a product finally. But the grinding process is very irregular, so it is very difficult to analyse the process accurately. Therefore it is very important in the aspect of precision and automation to reduce the idle time and to decide the proper dressing time by visualizing. In this study, we choose the direct method of observation by making use of computer vision, and apply pattern classification technique to the method of measuring the wheel surface. Pattern classification technique is proper to analyse complex surface image. We observe the change of the wheel surface by making use of the gray level run lengths which are representative prince in this technique.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.255-261
• /
• 2008

The importance of maintenance of rail surface defects is increasing according to the KTX operation. That is because during high speed operation of rolling stocks, rail surface defects shorten fatigue life of rail, accelerate track degradation and deteriorate ride comfort. Rail grinding has been applied for effective rail maintenance in Kyeong-Bu HS line. This paper evaluates the effectiveness of rail grinding in term of rail fatigue life. To this end, the stresses of the ground rail are measured under KTX running and the equivalent stress range is calculated by RMC after the frequency analysis done with Rainflow counting method. Also, Pamglen-Miner rule is applied to predict the fatigue life of ground rail. The result of the analysis shows that the fatigue life of ground rail is increased by 15%.

• 한국입자에어로졸학회지
• /
• 제9권1호
• /
• pp.1-6
• /
• 2013

New evaluation method for the particle size and morphology via change of ground particle during a grinding process was investigated. The grinding experiments were carried by a planetary ball mill. The relationship between the particle outline of the scanning electron microscopy photograph and measurement line, the measurement contact number was evaluated. The value of contact number decreased with the increase in the particle size of the ground sample, and varied with the experimental conditions. The value of contact number, which is related to the particle size of the raw sample, changed at the various experimental conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.755-756
• /
• 2013