• Korean Journal of Materials Research
• /
• v.10 no.10
• /
• pp.715-720
• /
• 2000

By the mechanical alloying method. Ni-WC composite materials were prepared to improve the deformation-resistance for creep and sintering of Ni-anode at the operating temperature of $650^{\circ}C$. Mechanically alloyed powder w was initially fabricated by ball milling for 80hr, and then amorphization was occurred by the destruction of ordered crystals based on XRD analysis. In order to investigate the electrochemical performance and sheet characteristics of Ni-WC anode, tape casting process was adopted. Finally, the obtained sheet thickness of Ni- we after sintering at $1180^{\circ}C$ for 60 minutes in $H_2$ atmosphere was O.9mm and the average pore size was $3~5{\mu\textrm{m}}$ with porosities of 55%. The second phase was not observed in Ni- W matrix while W particles were finely and uniformly distributed in Ni matrix. This fine and uniform distributed W particles in Ni matrix are expected to enhance the mechanical properties of Ni anode through the dispersion and solid solution hardening mechanisms.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.822-828
• /
• 2002

Fabrication and electrical characterization of R. F. High-power unit capacitors were investigated to study on condition of fabrication processing for R. F. High-power unit capacitor and electrical characteristics according to addition of $ZrO_2$. The unit capacitors were fabricated using tape casting. The optimum mixture ratio of dielectrics and mixing binder for the slurry fabrication was 57.5∼60.0: 42.5∼40.0 wt%. The slurry viscosity was 4000∼5000 cps and casting state of green tape fabricated using these slurry was excellent. Optimum stacking was made by 200 kg/$cm^2$ pressure with 80$^{\circ}C$ heating. $ZrO_2$ was added to improve the electrical characteristics of unit capacitor, especially breakdown characteristics. The dielectric constant and loss factor of the unit condenser having different $ZrO_2$ amounts was not changed in the addition range of 1 to 5 wt%. Also, dielectric constant was not changed in the frequency range of 10 to 500 kHz. It was found that characteristics of resistance voltage was improved through the formation of $CaZrO_3$ and the reduction of particle size as about 3wt% $ZrO_2$ was added.

• Journal of Adhesion and Interface
• /
• v.20 no.1
• /
• pp.9-14
• /
• 2019

The change of three different reagents for electrical conductive paint using aircraft coating with elapsing time of exposure to different condition was investigated. Three different reagents were poured into the vial bottles, stored in air condition and room temperature and observed with elapsing days. In addition, adhesion property of paint was tried using cross cut tape test after storage of $N_2$ atmosphere. The weight of each different reagent was measured along with elapsing time. To confirm the change of chemical component with exposure of air atmosphere, FT-IR was performed. The weight of part A and Part B decreased slightly whereas the weight of part C decreased rapidly and the precipitation was remained. The part B was cured after exposure of $N_2$ atmosphere and the 2250 cm-1 from FT-IR peak decreased slowly at the same time. It was considered that the water contained in air accelerated the reaction of -NCO functional groups and it caused the curing whereas $N_2$ atmosphere not contained water and it resulted in the retardancy of curing.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.122-129
• /
• 1999

Alumina tapes, having various weight ratios of alumina powder/(alumina+binder+plasticizer), X, and binder / (binder+plsticizer), Y, were prepared and their complex modulus was measured using Micro Fourier Rheometer. As the X and Y ratios increased, Transfer function(TF) magnitude and Transfer function (TF) phase increased and decreased, respectively, indicating that the elastic modulus of the tapes depends on the weight ratios. The temperature dependence of the viscosity of the tapes was visualized by the decreased TF magnitude and the increased TF phase. The Y ratio dependence of the complex modulus related to the glass transition temperature of the tapes and the moduls change by the Y ratio was higher than that by the X ratio within the comperature of the tapes and the modulus changes by the Y ratio was higher than that by the X ratio within the composition range, investigated in the present study. The measurement of the complex modulus of the alumina tapes suggested that the TF phase should be higher that 17$^{\circ}$for the tapes to be utilized for 3-dimensional shaping.

• Resources Recycling
• /
• v.7 no.4
• /
• pp.35-42
• /
• 1998

Surface mount technology is the biggest theme in the area of deιIronic component. To miniatunze an electronic component, s such as ferrite chip inductor, the cer뼈lic wet process for green-sheet lamination and/or screen printing method through a s solvent medium system is widely used. The preparation and characterization of NiCuZn Ferrite (NCZF) shurry and the green s sheet using the water mixed binder system has been studied. The 21 vol% of NCZF slurry was prepared by a ball milling. The p polyacrylic vinyl copolymer (Mw; 60,000) was used as a binder. Th$\xi$ mixture of distilled water, isopropyl alcohol (IPA) and 2l butoxy ethanol was used as a dispersion medium. The water content of medium varied from about 40% to 80%. As the results. Thc disp$\xi$rston stability of the NCZF slurry was attributed to the free polymer rather than the electrostatic force of the particle. T The viscosity of the NCZF slurry was greatly depended on the ratio of water content in the medium.

• Applied Chemistry for Engineering
• /
• v.34 no.5
• /
• pp.522-528
• /
• 2023

In this work, adhesive tapes were prepared for the dicing process in semiconductor manufacturing. Compounds with different numbers of photoreactive groups (f = 1 to 3) were synthesized and incorporated into acrylic copolymers to formulate UV-curable acrylic adhesives. Structural confirmation of the synthesized photoreactive compounds (f = 2 or 3) was performed using nuclear magnetic resonance (NMR) spectroscopy. The introduction of the photoreactive compounds into the acrylic adhesive was accomplished by urethane reactions, and the successful synthesis of the UV-curable acrylic adhesive was verified by Fourier transform infrared (FT-IR) measurements. To evaluate the performance of the adhesive, the peel strength was evaluated before and after UV irradiation using a silicon wafer as a substrate. The adhesive exhibited high peel strength (~2000 gf/25 mm) before UV exposure, which was significantly reduced (~5 gf/25 mm) after UV exposure. Interestingly, the adhesive containing multifunctional photoreactive compounds showed the most significant reduction in peel strength. In addition, surface residue measurements by field emission scanning electron microscopy (FE-SEM) showed minimal surface residue (~0.2%) after UV exposure. Overall, these results contribute to the understanding of the behavior of UV-curable acrylic adhesives and pave the way for potential applications in semiconductor manufacturing processes.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.28-34
• /
• 2010

This paper introduces a new U.S. ultra-wideband(UWB: 3.1~10.6 GHz) 1:2 power divider based on a single section Wilkinson type configuration. The divider provides very flat in-band power splitting, high isolation, low insertion loss, sharp roll-off bandpass filtering, and DC blocking characteristics. The circuit consists of a $\lambda$/4 Y resonator, three capacitively coupled $\lambda$/2 short-circuited lines, and a resistor between the two output ports. The circuit structure was simulated with ADS and HFSS, and realized with low-temperature co-fired ceramic(LTCC) green tape, which has a dielectric constant of 7.8. $|S_{11}|$ better than 10 dB, $|S_{21}|$ and $|S_{31}|$ less than 3.2 dB, with both $|S_{22}|$ and $|S_{32}|$ measured as better than 12 dB for the whole UWB band. Measurement results agree closely with HFSS simulation results. The power divider has a compact size of $4\times9\times0.6mm^3$.

• The Research Journal of the Costume Culture
• /
• v.4 no.3
• /
• pp.349-359
• /
• 1996

The research was designed to find out the effects of design elements ; ①color, ②pattern, on image perception of clothing by using a qualitative depth interview method. The subjects were 40 women who lived in Taejon and aged 20 to 40. The interview results were both hand recorded and tape recorded for further analysis by researchers and judge groups. And the results were as follows. 1. The most preferred colors appeared to be blue and black, while stripes, checks and flowers were most favorite patterns. 2. There were individual difference in color and pattern perception, however the color image of yellow was brightness, red was dashing, green comfortable, blue cool, and black tightness. The image of geometric pattern was modesty and natural motif pattern was dynamics. 3. The tow major forces which affected the image of design elements were appeared as followed : 1) Color images affected by the image of natural objects which obtained the color. 2) Individuals past experience and emotional status also affected the personal image perception. 4. The color and pattern preference for the Koran traditional customes and Western tow piece were significantly different and this result imply cultural stereotyping on image perception of design elements. On conclusion, the results supported the research model of form perception and image evaluation.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.164-173
• /
• 2009

In this paper, two new circuit structures for European and U.S. ultra-wide band(UWB) bandpass filters(BPFs) with sharp roll-off characteristics are introduced. We show first that the ultra-wide bandpass property is obtained from a $\lambda$/4 open T resonator with a capacitively coupled $\lambda$/4 short-circuited line, which provides two attenuation poles at lower and upper cutoff frequencies. Then, two identical capacitively coupled input/output lines, which can be $\lambda$/4-length open ends or $\lambda$/2-length short ends, with the T-resonator, are adopted to suppress lower and higher frequency components outside of the pass band. There is coupling between the input and output lines providing two additional transmission zeros in the lower and upper transition bands of the filter. Since the coupling between the T-resonator with the $\lambda$/4 short-circuited line and the input/output lines limits the bandwidth of the filter to the European UWB band, both the $\lambda$/4 short-circuited line and the input/output lines are inserted between the two stacked T-resonators for the U.S. UWB band. The filter structures are simulated with ADS and HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape which has the dielectric constant of 7.8. Measurement results agree well with HFSS simulation results.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.92-98
• /
• 2010

A new wideband bandstop filter(BSF) with a sharp roll-off characteristic is introduced in a stripline structure in this paper. The BSF consists of two sections: the first is two capacitively coupled $\lambda/4$ short-circuited lines with opposite ground positions, while the second is a capacitively coupled $\lambda/4$ short-circuited line. The BSF provides three transmission zeros within the stopband and better than 22 dB rejection over the whole wireless local area network (WLAN) band from 5.15 to 5.825 GHz. The BSF, cascaded to an U.S. ultra-wideband(UWB: 3.1~10.6 GHz) band-pass filter(BPF), is simulated with HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape with a dielectric constant of 7.8. The measurement results agree well with the HFSS simulation results. The size of the UWB BPF including the BSF is $3{\times}6.3\times0.45\;mm^3$.