• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.415-421
• /
• 2000

The effect of silica binder content on the mechanical properties of zircon shell mold was investigated. Content of binder silica sol to refractory powder in weight[$R_W$] was adjusted from 0.18 to 0.43. Sintering of the shell mold was carried out in the temperature range of $871^{\circ}C$ to $1400^{\circ}C$. Green strength of the shell mold at room temperature increased with increasing $R_W$ and sintering temperature up to $1300^{\circ}C$. However, the mold with $R_W$ of 0.43 that sintered at $1400^{\circ}C$ for 3 hours showed relatively low strength and large level of porosity. The mechanical behavior of the shells is supposed to attributed to the difference in thermal expansion coefficient between refractory powder and binder silica. The optimum value of $R_W$ for zircon-based shell molds was found to be 0.33.

• Korean Journal of Food Science and Technology
• /
• v.35 no.3
• /
• pp.393-398
• /
• 2003

Effects of convection oven dehydration conditions on the physicochemical and sensory properties of ginkgo nut powder were examined using three types of pre-treatment on ginkgo nuts: coarse grinding of ginkgo nut (GR); coarse grinding followed by 1 min blanching (GB); 3 min blanching followed by coarse grinding (BG). Pretreated ginkgo nuts were dried in convection oven at 70 and $80^{\circ}C$ to the moisture content of approximately 5%. Rehydration rate, swelling power, solubility, lightness, and greenness of GB ginkgo nut powder dried at $70^{\circ}C$ were the most similar to those of freeze dried one. GR and GB samples dried at $70^{\circ}C$ had higher sensory values of green color and ginkgo nut flavor. Ginkgo nut powder with desirable quality attributes could be produced by drying GB in convection oven at $70^{\circ}C$ for 10 hr.

• Korean Journal of Optics and Photonics
• /
• v.28 no.4
• /
• pp.166-171
• /
• 2017

Hydrogen gas is a green energy sources because it features no emission of pollutants during combustion. But hydrogen gas is very dangerous, being flammable and very explosive. Hydrogen gas detection is very important for the safety of a nuclear power plant. Hydrogen gas is generated by oxidation of nuclear fuel cladding during a critical accident, and leads to serious secondary damage in the containment building. This paper discusses the development of a Raman lidar system for remote detection and measurement of hydrogen gas. A small, portable Raman lidar system was designed, and a measurement algorithm was developed to quantitatively measure hydrogen gas concentration. To verify the capability of measuring hydrogen gas with the developed Raman lidar system, experiments were carried out under daytime outdoor conditions by using a gas chamber that can adjust the hydrogen gas density. As results, our Raman lidar system is able to measure a minimum density of 0.67 vol. % hydrogen gas at a distance of 20 m.

• Clean Technology
• /
• v.18 no.2
• /
• pp.162-169
• /
• 2012

Pt-Sn/${\theta}-Al_2O_3$ catalyst for n-butane dehydrogenation reaction was prepared by incipient wetness method. To confirm the physicochemical properties of Pt-Sn/${\theta}-Al_2O_3$ catalyst, the characterization was performed using X-ray diffraction (XRD), $N_2$ sorption analysis, temperature programmed desorption of $NH_3$ ($NH_3$-TPD), temperature programmed reduction of $H_2$ ($H_2$-TPR) techniques. Also, the catalytic activities of Pt-Sn/${\theta}-Al_2O_3$ for n-butane dehydrogenation was tested as a function of pretreatment temperature, pretreatment time, reaction temperature, and the partial pressure of n-butane and hydrogen. The sum of selectivities to n-butenes consisting of 1-butene, cis-2-butene, and trans-2-butene was almost constant 95% in the range of conversion of n-butane 5-55%. The activation energy calculated from Arrhenius equation was $82.4kJ\;mol^{-1}$ and the reaction orders of n-butane and hydrogen from Power's law were 0.70 and -0.20, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.51-57
• /
• 2016

In this study, we synthesized reactive surfactant which have functional radical group for effective chemical reaction. Reactive surfactant have been synthesized using synthesis of polyoxyethylene lauryl ether(POE 23) which is nonionic surfactant and methacrylic acid, acrylic acid. benzene was used as the solvent, p-TsOH was used as the catalyst. synthesized surfactant was confirmed by FT-IR, $^1H$-NMR spectra, and elemental analysis. Evaluation of physical properties was measured HLB, cloud point, surface tension, the critical micelle concentration, emulsifying power. HLB number was evaluated 11.62 to 12.09 range. The Critical Micelle Concentration(cmc) values evaluated was $1{\times}10^{-4}{\sim}5{\times}10^{-4}mol/L$ by surface tension method. The cloud point was $35^{\circ}C$, $39^{\circ}C$ each. The emulsifymvcqa ing properties of the synthesized surfactants was lower than polyoxyethylene lauryl ether. In addition, soybean oil was better than benzene. The experimental results confirmed the ester bond, the yield of 93.27%, 94.49% was found.

• Korean Business Review
• /
• v.18 no.1
• /
• pp.59-79
• /
• 2005

recently, world is progressing large quantity consumption with continuous Innovation and economic growth and pollution is accelerated at these process. Increase of industry activity and service that is point of corporation activity is discharging environmental pollutants at whole process to manufacture of end product and exhaust process from acquisition of raw material for accompanied product production hereupon. At the same time, being promoting resources consumption by that use much raw material, As a result, is becoming obstacle factors in sustainable development. So, corporation's responsibility for environmental protection is emphasized. Corporation which must prepare in green round or environmental problems should consider environmental effects that is happened over whole life of products that include waste treatment after raw material acquisition and use as well as selling end product simply. A Life Cycle Assessment techniques is normalized and standardized in International Standard Organization for technical committee 207(TC 207) world widely, and effort to apply in corporation's activity because mastering LCA techniques in domestic several corporations is undergone actively. Coming into effect of Kyoto's Protocol and International Organization for Standard 14000 series revision are presenting new survival principle in competition between country or corporation. LCA technique may become very useful means to corporation which wish to attempt environment management in real condition that awareness for environment is important. Also, An LCA to each product is going to cause big effects in corporation's whole image as well as competitive power raising for single product. Therefore, this research wishes to examine some instances for the future competitive product development at the estimation of environmental friendliness using LCA techniques and more theoretical considerations of the LCA techniques that can dominate corporation's fate.

• Journal of Bio-Environment Control
• /
• v.25 no.3
• /
• pp.139-145
• /
• 2016

The objective of this study was to compare the growth and light use efficiency of red leaf lettuce grown under three types of combined light-emitting diodes (LEDs) and fluorescent lamps (FL) in a closed-type plant production system. The eighteen days-old lettuce seedlings of red leaf lettuce (Lactuca sativa L., 'Jeokchima') were transplanted to the close-type plant production system equipped with three types of combined LEDs with red (R, 655 nm), blue (B, 456 nm), green (G, 515 nm), and white (W, 456 nm + 558 nm) (R:B=8:2, R:W:B=8:1:1, R:G:B=8:1:1) and FL. The seedlings were grown under normal growth conditions ($20^{\circ}C$, $181{\pm}4{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, 12 h photoperiod) for four weeks. Lettuce plants grown under FL had significantly higher leaf shape index than those under all LED treatments. Although growth of shoots and roots was not show any significant difference among LED treatments, all of the LED treatments induced about 34% higher shoot fresh weight than that of the FL. On the other hands, the total power consumption of FL was 145 kW for 4 weeks, while the mean value of LED treatments was 54 kW, which was about 3 times lower value than that of the FL. The light use efficiency based on dry matter in LED treatments was about 34 mg/W and this was about 3.5 times higher energy saving value than the FL. In conclusion, this study showed that irradiation of optimal combined LEDs in closed-type plant production systems can improve the lettuce growth as well as maximize in light use efficiency through energy saving than the FL.

• Clean Technology
• /
• v.18 no.4
• /
• pp.446-450
• /
• 2012

Strong alkaline electrolyzed water which is produced in cathode by electrolyzing the solution where electrolytes (NaCl, $K_2CO_3$ etc.) are added in diaphragm electrolytic cell, is eco-friendly and has cleaning effects. So, it is viewed as a substitution of chemical cleaner. In addition, strong alkaline electrolyzed water is being used by some Japanese automobile and precision parts manufacturing industries. When strong alkaline electrolyzed water is produced by using diaphragm electrolytic cell, it is necessarily produced at the anode side. Since strong acidic electrolyzed water produced is discarded when its utilization cannot be found, production efficiency of electrolyzed water is consequently decreased. Also, there is a weakness electrolytic efficiency is decreasing due to the pollution of diaphragm. In order to overcome this, non-diaphragm all-in-one electrolytic cell integrated with electrode reaction chamber and dilution chamber was applied. Strong alkaline electrolyzed water was produced for different composition of electrolytes, and their properties and characteristics were identified. In comparing the properties between strong alkaline electrolyzed water produced in diaphragm electrolytic cell and that produced in all-in-one electrolytic cell, the differences in ORP and chlorine concentration were found. In emulsification test to confirm surface-active capability, similar results were obtained and strong alkaline electrolyzed water produced in non-diaphragm all-in-one electrolytic cell was identified to be useable as a cleaner like strong alkaline electrolyzed water produced in diaphragm electrolytic cell. Strong alkaline electrolyzed water produced in non-diaphragm all-in-one electrolytic cell is thought to have sterilizing power because it has active chlorine which is different from strong alkaline electrolyzed water produced in diaphragm electrolytic cell.

• Membrane Journal
• /
• v.21 no.4
• /
• pp.367-376
• /
• 2011

Huge amount of $CH_4$ mixtures has been emitted from landfills and organic wastes via anaerobic digestion. The recovery of high purity $CH_4$ from these gases has two merits: reduction of green house gases and production of renewable fuels. Membrane technology based on polymeric materials can be used in this application. In this study, asymmetric gas separation hollow fiber membranes were fabricated to develop the membrane-based bio-gas purification process. Polyethersulfone (PES) was chosen as a polymer materials because of high $CO_2$ permeability of 3.4 barrer and $CO_2/CH_4$ selectivity of 50[1]. Acetone was used as a non-solvent additive because of its unique swelling power for PES and highly volatile character. The prepared PES hollow fiber showed excellent separation properties: 36 GPU of $CO_2$ permeance and 46 of $CO_2/CH_4$ selectivity at optimized preparation conditions: 9wt% acetone content, 10cm air-gap and 4wt% PDMS coating processes. With the PES hollow fiber membranes developed, mixed $CO_2/CH_4$ test was done by changing various operating conditions such as pressures and feed compositions to meet the highest recovery of CH4 with 95% purity. High $CH_4$ recovery of 58 wt% was observed at 10 atm feed pressure for the 50 vol% of $CO_2$ in $CO_2/CH_4$ mixture.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.33-39
• /
• 2010

The spheric sintered body with $6{\pm}2mm$ diameter was manufactured in a rotary kiln at $1125^{\circ}C$/15 min using green body formed by pelletizing the batch powder composing of coal bottom ash produced from power plant and dredged soil by 70:30, wt%. And the physical properties of sintered body (BD) were analyzed to confirm the possibility for applying to an absorbent to restore a contaminated soil. The sintered body had a giant pore above 100 ${\mu}m$ and a fine pore below 10 ${\mu}m$, and bulk density was 1.4. Also its specific surface area, porosity and void proportion were $12.0m^2/g$, 30.1% and 38.2% respectively. The crushed body (BD-C), produced by crushing a BD specimen into an irregular shape with a aspect ratio of about 2, was similar to BD specimen at bulk density and pore size distribution. But it had superior values of specific surface area, porosity and void proportion compared with BD specimen owing to a decreased apparent volume due to conversion of closed pore existed at interior of BD to open pore during a crushing process. The IEP of sintered body occurred at about pH=5, so the optimum pH condition of reacting aqueous solution could be known before bonding a microbe to the sintered body. Hence, the optimum void proportion and porosity of an absorbent can be obtained by appropriate mixing a BD with BD-C from the base data calculated in this study.