• 한국세라믹학회지
• /
• 제32권2호
• /
• pp.147-154
• /
• 1995

Abnormal grain growth behavior of BaTiO3 ceramics with controlling of particle size distribution of calcined powder was investigated. The particle size distribution was controlled by changing the calcining temperature or by using of classification and regrinding process. With broadening of the normallized size distribution in calcined powder, it showeda normal grain growth behavior in sintered body due to an increase of volume fraction of seed grain in the calcined powder. It was supposed that the seed grains could easily contact each other for the rapid grain growth during sintering process and resulted in fast switching-over from abnormal to normal grain growth stage.

• 한국주조공학회지
• /
• 제5권2호
• /
• pp.85-96
• /
• 1985

In order to investigate the effect of particle size and distribution of silica sand on the characteristics of investment, W/P ratio, setting time, temperature change during setting, setting expansion, thermal expansion and compressive strength of the investments were measured. In this experiment, magnesia clinker and mono ammonium phosphate were used as binder, and particle size and distribution of silica sand were classified for convinence into 10 categories. The main results obtained from this investigation were summerized as follows. 1. W/P ratio decreased with increase of particle size and evenness in distribution of sand grain. 2. Setting time decreased with increase of evenness in distribution of sand grain, and temperature during setting increased with evenness in distribution of sand grain. 3. Setting expansion decreased with increase of particle size, while it increased with evenness in distribution of sand grain. 4. Thermal expansion decreased with increase of particle size. 5. Compressive strength increased with increase of particle size and evenness in distribution of sand grain. From above results, G.F.N. 250 sand which contains 30% of 50-100 mesh could be recommended for investment casting.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.46-46
• /
• 2006

$SrTiO_3$ was annealed at two different annealing times (1 h and 16 h) to investigate the annealing effect on the grain size and orientation distribution. Electron backscattered diffraction (EBSD) was used to analyze the grain size and grain orientation distributions of the $SrTiO_3$. It is possible to understand the annealing effect on the microstructure evolution, by comparing the grain size and orientation distribution of the $SrTiO_3$ as a function of annealing time.

• 한국세라믹학회지
• /
• 제30권3호
• /
• pp.199-205
• /
• 1993

Effects of grain size distribution on the breakdown voltage of ZnO varistors were investigated in the ZnO-Bi2O3-CoO-Sb2O3 and ZnO-Bi2O3-CoO-Sb2O3-Cr2O3 systems, respectively. The grain size was increased with increasing sintering temperature maintaining lognormal distribution in both systems. The width of grain size distribution of ZnO-Bi2O3-CoO-Sb2O3 system was narrower than that of ZnO-Bi2O3-CoO-Sb2O3 system. The breakdown voltage(Vb) was decreased by increasing sintering temperature(1000~135$0^{\circ}C$) and sintering time(0.5~5hr), due to the enhancement of ZnO grain growth. The current path of the ZnO varistor was dependent on the distribution of the largest grains (chains of long grains) between the electrodes.

• 한국해양학회지
• /
• 제28권2호
• /
• pp.114-120
• /
• 1993

입도분포의 특징분석에 종래의 조직특성치 대신 수치해석적인 분해법의 적용을 시 도하였다. 그 결과 이 방법이 제주해협의 대륙붕 표층퇴적물과 같은 복모드형 입 도분포의 분석에 매우 유용함이 입증 되었다. 복모드형 입도분포 퇴적물은 제주해협 대륙붕에서는 86%의 높은 비율을 점한다. 종래의 입도특성치(평균, 표준편차, 왜도, 첨도)는 복모드형 입도분포에 대해서는 왜곡된 값을 보인다. 따라서 입도분포의 모드 에 대체로 대응되는 정규성분으로 분해해서 각 정규성분의 특성치를 해석함으로써 입 도특성치에서와 같은 특징의 누락이나 왜곡을 피할 수 있다. 제주해협 대륙붕의 167개 퇴적물 입도분포곡선을 비선형 최소자승법을 사용하여 정규성분으로 분해해서 총 387 개의 정규성분을 얻었다. 정규성분의 평균은 1-3 phi 8-9 phi에 집중되는 것이 많다. 이중 조립질 정규성분의 평균치는 복잡하고 특징적인 지리적 분포를 보인다. 이러한 분포는 퇴적물 총층후 분포와 매우 유사하며 해저면의 지질과 지형을 면밀하게 반영하 고 있다. 해저면을 형성하는 퇴적층은 플라이스토세 후기의 해침성 모래층이며 해저지 형은 플라이스토세말 빙하기 저해수면시기의 침식에 의해 형성된 것으로 보인다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.663-668
• /
• 2000

In this study, the Atterberg limit and grain-size analysis were carried for the purpose of investigating the influence on drying and organic matter of Ulsan marine deposited clay. The results revealed that Atterberg limit was decreased and grain-size distribution was variable on drying. The presence of organic matter also influenced on the physical properties of the soils. The physical properties of marine deposited clay were variable on drying, so that we recommended grain-size analysis and Atterberg limit test were performed under the wet condition of the soils after sampling.

• 한국농공학회논문집
• /
• 제48권6호
• /
• pp.59-67
• /
• 2006

Particles of soil are crushed when soil is compacted in the in-situ or lab. Among many factors that affect the crush of particles, compaction energy is a major factor. Because the crush of particles can change physical properties, the analysis of effect of compaction energy is very important. In this study, the fragmentation fractals were used for determining the change in grain size distribution and the effect due to change in grain size distribution was estimated. Compaction energy was increased by 50, 100, 200 and 300% based on the energy of standard A compaction test. As a result, grain size distribution curves were changed and fine particles increased as compaction energy were increased. Relative compaction were ranged between $93.38{\sim}107.67$. Fractal dimension of each site increased as compaction energy increased. Relative compaction is proportional to the fractal dimension but coefficients of permeability were in inverse proportional to the involution of fractal dimension.

• 한국세라믹학회지
• /
• 제33권5호
• /
• pp.602-615
• /
• 1996

The purpose of the present study is to investigate the microstructural effect on the R-curve behavior in three aluminas with different grain size distributions by analyzing the bridging stress distribution. The crack opening displacement (COD) according to the distance behind the stationary crack tip was measured using an in situ SEM fracture method. The measured COD values in the fine-grained alumina agreed well with Wiederhorn's sollution while they deviated from Wiederhorn's solution in the two coarse-grained aluminas because of the increase of the crack closure due to the grain interface bridging in the crack wake. A numerical fitting procedure was conducted by the introduction of the power-law relation and the current theoretical model together with the measured COD's in order to obtain the bridging stress distribution. The results indicated that the bridging stress function and the R-curve computed by the current model were consistent with those computed by the power-law relation providing a reliable evidence for the bridging stress analysis of the current model. The strain-softening exponent in the power-law relation n, was calculated to be in the range from 2 to 3 and was closely related to the grain size distribution. Thus it was concluded from the current theoretical model that the grain size distribution affected greatly the bridging stress distribution thereby resulting in the quantitative analysis of microfracture of polycrystalline aluminas through correlating the local-fracture-cont-rolling microstructure.

• 한국재료학회지
• /
• 제32권10호
• /
• pp.414-418
• /
• 2022

Magnesium alloy is the lightest practical metal. It has excellent specific strength and recyclability as well as abundant reserves, and is expected to be a next-generation structural metal material following aluminum alloy. This paper investigated the possibility of thin plate fabrication by applying a overheating treatment to the melt drag method, and investigating the surface shape of the thin plate, grain size, grain size distribution, and Vickers hardness. When the overheating treatment was applied to magnesium alloy, the grains were refined, so it is expected that further refinement of grains can be realized if the overheating treatment is applied to the melt drag method. By applying overheating treatment, it was possible to fabricate a thin plate of magnesium alloy using the melt drag method, and a microstructure with a minimum grain size of around 12 ㎛ was obtained. As the overheating treatment temperature increased, void defects increased on the roll surface of the thin plate, and holding time had no effect on the surface shape of the thin plate. The fabricated thin plate showed uniform grain size distribution. When the holding times were 0 and 30 min, the grain size was refined, and the effect of the holding time became smaller as the overheating treatment temperature increased. As the overheating temperature becomes higher, the grain size becomes finer, and the finer the grain size is, the higher the Vickers hardness.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 추계학술발표대회 개요집
• /
• pp.220-222
• /
• 2001

The average grain size, the grain-size distribution, the morphology and the microstructure are fundamental characteristics of a spraying powder. Now that the significance of the grain size for the pattern of properties of the powder has been recognised, greater consideration is also being given to it in standards and regulations. However, unfortunately, the processes according to which the grain size and the grain-size distribution must be determined are specified in the rarest of cases. The contribution therefore dealt with the comparison of different particle-size measuring techniques, such as diffraction spectroscopy, sedimentation, sieving and microscopic measurement. The comparability of the measured results was investigated on twelve plasma spraying powders with different compositions, nominal sizes and morphologies.