• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.421-424
• /
• 2007

Dry sliding wear behavior of ultra-fine grained (UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1162-1164
• /
• 1995

In this paper, $TiO_2$-xmol%$V_2O_5$, x=0.0, 1.0, 2.0, 3.0 specimens are fabricated by Sol-Gel method. For the improvement of humidity sensitive characteristics for specimens, their microstructures are analysed and the optimum processing condition is established. Grain size increases with substitution rate of $V^{5+}$, on $Ti^{4+}$ site. Their humidity sensitive characteristics is good at 1mol% of $V_2O_5$ rate and heat-treated at $700^{\circ}C$. The capacitance of specimens decreases with frequency.

• Economic and Environmental Geology
• /
• v.22 no.2
• /
• pp.103-115
• /
• 1989

The Tongyoung deposits are epithermal gold and silver bearing quartz-rhodochrosite vein type deposits of late Cretaceous. They occurs in the andesite and tuff breccia member called Gyeongsang basin. Four mineralizations can be distinguished at the mine based on macrostructures. From earlist stage to lastest stage they are: stage I, base-metal quartz vein; stage II, rhodochrosite vein (IIA) and Pb-Zn vein (IIB); stage III, barren quartz vein; stage IV, calcite-ankeritic rhodochrosite veins. Gold and silver mineralizations occur predominantly in the stage I and IIB. Electrum is closely associated with galena, sphalerite and pyrite, and has chemical compositions of 50.98-64.05 atom % Ag. Sphalerite contains 2.09-5.05 mol % FeS and 0.34-2.01 mol % MnS in the stage I, and 2.01-3.41 mol % FeS and 0.21-2.80 mol % MnS in the stage IIB. The FeS and MnS contents are in general correlated, and shows a characteristic zonal arrangement of electrum. It reveals rhat FeS contents of sphalerite which precipitated before electrum, gradually decreases in a grain during its deposition ranging from about 3.3 to 2 mol %. It may be considered from the above data that an increase of $fs_2$ caused by the oxidation of ore forming fluid is more important that the decrease of temperature.

• Korean journal of food and cookery science
• /
• v.27 no.6
• /
• pp.745-754
• /
• 2011

To improve the textural properties of gluten free rice flour based products, the physicochemical and pasting properties of extruded non-waxy rice flours using extruder were investigated. The high yielding Tongil type rice variety, Hanarum was used. Hanarum rice flour was prepared by dry milling from soaked and dried rice grain. The operation conditions of twin screw extruder were 250 rpm of screw speed, $160^{\circ}C$ of barrel temperature, and 24, 27, and 30% of moisture content. Hanarum extruded rice flour (HERF) were lower in crude lipid and ash contents, but higher in crude protein than Hanarum rice flour (HRF). The color values of HERF showed significantly different (p<0.05) with different moisture contents. Water binding capacities, apparent amylose contents, and damaged starch of HERF were higher than those of HRF. Moisture contents affected water binding capacities of HERF. Solubility increased with increasing heating temperature and solubilities of HERF differed significantly (p<0.05). X-ray crystallinity was changed after extrusion cooking and that of HERF showed sharp peaks at $2{\theta}=18-20^{\circ}$. The pasting viscosities of HERF kept lower values (~ 10 RVU) constantly.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.969-973
• /
• 2012

AlN thin films were deposited on p-type Si(100) substrates by RF magnetron sputtering method. This study showed the change of the preferential orientation of AlN thin films deposition with the change of the deposition conditions such as sputtering pressure and Ar/N2 gas ratio in chamber. It was identified by X-ray diffraction patterns that AlN thin film deposited at low sputtering pressure has a (002) orientation, however its preferred orientation was changed from the (002) to the (100) orientation with increasing sputtering pressure. Also, it was observed that the properties of AlN thin films such as thickness, grain size and surface roughness were largely dependent on Ar/$N_2$ gas ratio and a high quality thin film could be prepared at lower nitrogen concentration. AlN thin films were investigated relationship between preferential orientation and deposition condition by using XRD, FE-SEM and PFM.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.399-403
• /
• 2012

SnO thin films were fabricated by rf reactive sputtering on borosilicate substrates with an Sn target and Ar/$O_2$ gas mixture. The effect of rf power on the structural, electrical, and optical properties of SnO thin films was investigated with XRD, AFM, SEM, Hall effect measurements, and UV-Vis spectrometer. As a plasma power increased the crystallinity with a preferred orientation of SnO thin films was improved and the grain size slightly increased. However the grains were coalesced and excessively irregular in shape. The electrical conductivity of SnO thin films demonstrated a relatively low p-type conductivity of 0.024 $(Wcm)^{-1}$ at a higher power condition. Lastly, SnO thin films had poor optical transmittance in the visible range as a plasma power increased.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.340-340
• /
• 2016

We have prepared alumina (Al2O3) doped zinc oxide (AZO) films by DC magnetron sputtering (MS) technique and obtained higher self surface texturing at a high target angle (f). We have characterized the films and applied it as a front electrode of a single junction amorphous silicon solar cell. At a lower f the deposited films show higher values of optical gap (Eg), charge carriers mobility & concentration, crystallite grain size and wider wavelength range of transmission. At higher target angle the sheet resistance, surface roughness, haze factor etc for the films increase. For f=72.5o the haze factor for diffused transmission becomes 6.46% at 540 nm wavelength. At f=72.5o the material shows a reduction in crystallinity and evolution of a hemispherical-type sub-micron surface textures. A Monte Carlo method (MCM) of simulation of the AZO film deposition shows that such an enhanced self-surface texturing of the films at higher f is possible.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.9-9
• /
• 2009

1 wt % Ga-dope ZnO (ZnO:Ga) thin films with n-type semiconducting behavior were grown on c-sapphire substrates by radio frequency magnetron sputtering at various growth temperatures. The room temperature grown ZnO:Ga film showed the faint preferred orientation behavior along the c-axis with small domain size and high density of stacking faults, despite limited surface diffusion of the deposited atoms. The increase in the growth temperature in the range between $300\sim550^{\circ}C$ led to the granular shape of epitaxial ZnO:Ga films due to not enough thermal energy and large lattice mismatch. The growth temperature above $550^{\circ}C$ induced the quite flat surface and the simultaneous improvement of electrical carrier concentration and carrier mobility, $6.3\;\times\;10^{18}/cm^3$ and $27\;cm^2/Vs$, respectively. In addition, the increase in the grain size and the decrease in the dislocation density were observed in the high temperature grown films. The low-temperature photoluminescence of the ZnO:Ga films grown below $450^{\circ}C$ showed the redshift of deep-level emission, which was due to the transition from $Zn_j$ to $O_i$ level.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.22 no.2
• /
• pp.37-41
• /
• 1977

Zeolite was applied of the tidal land and its effect on growth and yield of the two rice varieties, Yushin and Jinheung, was studied. The salinity of the zeolite treated soil was lower than that of the control. The effect of zeolite on growth of rice was appeared at the maximum tillering stage. The remarkable effect of zeolite on grain yield appeared in the variety Yushin, an indiea type. The amount of 600kg/10a was recognized to be an optimum amountd of the zeolite application in the tidal land.

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.2
• /
• pp.56-61
• /
• 2016

Heating experiments using the Ti-3Al-2.5V tube materials in a vacuum furnace have been performed to investigate a pertinent range of working temperatures and holding times for the development of the successive or simultaneous operation of superplastic hydroforming and diffusion bonding. The specimens were heated at $820^{\circ}C$, $870^{\circ}C$ and $920^{\circ}C$ respectively. Holding times at each temperature were varied up to 4 hours. Holding times longer than 1 hour were selected to consider the diffusion bonding process after or during the hydroforming process in the superplastic state. Grain sizes were varied from $5.7{\mu}m$ of the as-received tube to $9.2{\mu}m$ after heating at $870^{\circ}C/4hours$. Homogeneus granular microstructures could be maintained up to $870^{\circ}C$, while microstructures at $920^{\circ}C$ showed no more granular type.