• Journal of Welding and Joining
• /
• v.34 no.1
• /
• pp.35-40
• /
• 2016

Recent developments of Laser metal 3D deposition with wire feeding are reviewed which provide an alternative to powder feeding method. The wire feeding direction, angle and position as well as laser power, wire feeding rate, and deposition speed are found to be key parameters to make quality deposition with high throughput. When compared with the powder feed, the wire feed shows higher material efficiency, higher deposition rate, and smoother surface. Large elongated columnar grains which have epitaxial growth across deposit layers are observed in deposit cross sections. The growth direction is parallel to the thermal gradient during the deposit process. Tensile properties are found to be dependent on the direction due to the anisotropic deposit property. A real-time feedback control is demonstrated to be effective to improve the deposition stability.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.296-298
• /
• 1995

This paper proposes a new filter topology that suppresses the high voltage gradient(dv/dt) in ac motor terminals. The high voltage gradient(dv/dt) causes over voltages on the motor windings, the degradation or motor insulation, and the bearing failure. Moreover surge voltage with high voltage gradient(dv/dt) in the PWM inverter red drive system where long line cables are required causes more serious problem to the motor. Thus, the most advisable method is attaching output filter to the inverter output terminals. The conventional output filters have several problems such as bulky size, difficulty or parameter tuning. The proposed filter can be relatively smaller than the conventional filters. By the proposed filter, the shaping or PWM waveform can considerably suppress high dv/dt in motor feeding cable from the inverter. The effectiveness or the proposed filter is compared with that or the conventional one and is verified by the computer simulation.

• Journal of Microbiology and Biotechnology
• /
• v.12 no.2
• /
• pp.273-278
• /
• 2002

Two-step fed-batch fermentations were carried out to overproduce Bacillus licheniformis maltogenic amylase (BLMA) in recombinant Escherichia coli. The first step was to increase the cell mass by controlling the feeding of a glucose solution, while the second step was designed to improve the amylase expression efficiency by supplementing organic nitrogen sources. The linear gradient feeding method was successfully adopted to maintain the glucose concentration below 0.2 g/l during the fed-batch mode, as effectively minimizing acetic acid formation. When the dissolved oxygen (DO) level became limiting, an accumulation of acetic acid and drastic decrease in specific BLMA productivity were observed. Glucose and organic nitrogen sources consisting of yeast extract and casein hydrolysate were simultaneously supplied in the pH-stat mode to further increase the specific BLMA expression efficiency. An organic nitrogen source consisting of 200 g/1 yeast extract and 100 g/1 casein hydrolysate was found to be the best among the various combinations tested. The feeding of an organic nitrogen source in the second-step fed-batch period was highly beneficial in enhancing the BLMA production. The optimized two-step fed-batch culture resulted in 78 g/l maximum dry cell mass and 443 U/ml maximum BLMA activity, corresponding to 1.5-fold increase in the dry cell mass and 3.7-fold enhancement in BLMA production, compared with the simple fed-batch fermentation.

• Macromolecular Research
• /
• v.9 no.2
• /
• pp.122-128
• /
• 2001

Monodisperse composite latex particles with size of ca. 300 nm, which consist ofn-butyl acrylate as a soft phase and methyl methacrylate as a hard phase with different morphology, were synthesized by seeded multi-stage emulsion polymerization. Three types of composite latex particles including random-, core/shell-, and gradient-type particles were obtained by using different monomer feeding methods during semi-batch emulsion polymerization. Effect of poly(butyl acrylate)-poly(methyl methacrylate) rubber particle morphology on the mechanical and rheological properties of rubber toughened poly(methyl methacrylate) was investigated. Among three different rubber particles, the gradient-type rubber particle showed better toughening effect than others. No significant variation of rheological property of poly(methyl methacrylate)/rubber blends was observed for the different rubber particle morphology.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.1-13
• /
• 1997

The key point that guarantees the durability of the ceramic monolith filter is to lower peak temperature and temperature gradient inside filter during regeneration. The control of the exhaust gas flow rate into the filter, by the bypass technique of the exhaust gas, enables the gas temperature in filter to be constant for regeneration. A couple of methods, which are the ON/OFF and PID control of the bypass valve, were used for feedback control of the gas temperature. These techniques showed that the ceramic filter was regenerated perfectly under the peak temperature and peak temperature gradient limitations for durability.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.539-543
• /
• 1992

The continuous growth method was developed for Mn-Zn Ferrite single crystals. It is a new process that the polycrystalline MnχZn1-χFe2O4 raw materials are supplied continuously from the powder feeding system to the crucible heated by R.F. induction and melted in the crucible, and after the single crystals seed is attached to crucible's hole, the crystals are pulled downward with rotation. Growing the crystals by using the growth method different from the conventional Bridgman or Floating Zone method, we defined the factors having effect on the crystal growing through the pre-experiments. They are temperature distribution in the crucible, melt velocity according to its height, wettability between the crucible's bottom and melt. Therefore, Mn-Zn Ferrite single crystals were to be grown by attaining the appropriate melt height in the crucible, powder feeding rate, temperature gradient between the crucible and interface, crystal growing speed, and this method was confirmed to have possibility for single crystal growing.

• KSBB Journal
• /
• v.15 no.3
• /
• pp.219-225
• /
• 2000

Both the production of high spore concentration and high insecticidal activity are required in the production of Bacillus thuringiensis to be used for the bacterial insecticide. In the production of high cell and spore concentrations of B. thuringiensis the continuous fed-batch culture(CFBC) and intermittent fed-batch culture(IFBC) were investigated at $28^{\circ}C$ by maintaining 40% dissolved oxygen concentration. When the final glucose concentration was 50 g/L the maximum viable cell number obtained using the CFBC with linear gradient feeding was $9.37{\times}109$ cells/mL and maximum spore concentration was $8.33{\times}109$ spores/mL which was approximately 84.4% yield of spore formation. When the final glucose concentration was 100 g/L the aximum viable cell and spore concentrations obtained using the IFBC with pH-statb were $1.38{\times}$1010 cells/mL and $1.35{\times}1010$ spores/mL respectively and the yield of spore formation was approximately 97.8%.

• Journal of Korea Foundry Society
• /
• v.11 no.1
• /
• pp.44-53
• /
• 1991

The proper feeding conditions for thin Al-Alloy (AA336, JIS AC8A) castings in permanent mold were investigated to eliminate microshrinkage porosity. 5mm-thick plates (200mm long, 60mm wide) were cast with increasing padding taper from 0 to 5% under different conditions : (1) constant mold temperature of $350^{\circ}C$, (2) continuous production with uniform mold thickness (10mm), (3) continuous production with a negative taper of 2.5% in mold thickness (thickness decreasing in direction to riser). The test casting were machined off to the midplane and the shrinkage porosity was examined visually. The critical padding taper which can just eliminate the shrinkage porosity was determined for each condition, i.e. : (1) 4.5% at the constant mold temperature, (2) 3.5% for continuous production with the uniform mold thickness (3) 1.5% for continuous production with the taper in mold thickness. A computer simulation by a finite difference analysis program was applied to the test casting. The liquid fraction gradient (LFG) and the temperature gradient divided by the square root of the cooling rate (G /SR) were calculated at the end of solidification and compared with the shrinkage porosity area in the castings. For the case of constant mold temperature, LFG is a better parameter to predict shrinkage porosity than G /SR and its critical value is around 11%/cm. But for the case of continuous production, neither LFG nor G /SR could be a reliable parameter. The experimental results about the critical padding taper are of practical interest for designing permanent molds and castings. The computer simulation results stimulate further research to be directed on the prediction of centerline microshrinkage porosity in continuous production.

• Applied Biological Chemistry
• /
• v.19 no.3
• /
• pp.121-129
• /
• 1976

A high concentration of myo-Inositol in rat's milk was observed (61-91mg. of myo-Inositol per 100g of milk) by gas-liquid chromatographic method, using a 3% SE-52 column. Feeding experiments showed that approximately 85% of myo-Inositol in milk was from dietary origin: the rest was considered to be synthesized by 1L-myo-Inositol-1-phosphate lyase. Results suggested that the biosynthesis was not sufficiently high to permit the maintenance of its myo-Inositol level in milk. However, study $using(^{14}C)-glucose$ injection into lactating female rats confirmed biosynthesis of myo-Inositol from glucose in mammary gland. This biosynthesis reached a maximum within an hour after $(^{14}C)-glucose$ injection intraperitoneally as lactose biosynthesis did. Study using $(^3H)-myo-Inositol$ confirmed that most of the myo-Inositol in milk was transported from blood plasma myo-Inositol against a concentration gradient. About four hours after the beginning of the injection of $(^{14}C)-glucose$, the specific radioactivity of myo-Inositol in milk was 8% of that of glucose in the blood. When $(^3H)-myo-Inositol$ was injected, the specific radioactivity of myo-Inositol in milk was about 26% of that of blood six hours after injection.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.78-84
• /
• 1996

In order to eliminate TPM(Total Particulate Matter) from a diesel engine, we designed and developed a particulate trap system using a burner, which was named as AEFR(Active Exhaust Feeding Regeneration) system. We have considered the temperature distributions and gradients in the filter being regenerated according to regeneration control schemes Ⅰ, Ⅱ and Ⅲ. Schemes Ⅲ has shown the most desirable peak temperature and temperature gradients in AFER system. Finally, it was concluded that much lower peak temperature and temperature gradients in the filter could be obtained than that of other advanced research results by our AEFR system.