• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.4
• /
• pp.16-21
• /
• 2002

It was observed that drying temperature and curing time in the paper coating process as well as Tg of the latex used as a binder, greatly affected the properties of the coated paper such as roughness, paper and print gloss, K & N ink drop, and ink set-off. The higher drying temperature induced faster water evaporation and change in binding density, which caused an increase in paper roughness, ink gloss and ink set-off, but decrease in paper gloss and K & N ink drop. The increased curing time promoted latex filming and redistribution of the binder in coating layer. This increased pick strength and ink gloss, but decreased ink trapping. Finally, the higher Tg of the latex showed the wider changing range of these properties.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.1
• /
• pp.26-35
• /
• 1997

A study was carried out to investigate such optical properties of coated papers as brightness, opacity and gloss affected by the coating pigment composition and coat weight using clay, ground calcium carbonate, precipitated calcium carbonate, and plastic pigment as pigments. The effects of drying methods and supercalendering on optical properties were also evaluated. Gloss increased abruptly while brightness and opacity decreased slightly by supercalendering due to surface smoothing and consolidating effects of the coating layers. Optical properties changed little by drying methods. Pigment composition showed significant influences on optical properties. Brightness of coated papers decreased or increased linearly as the coat weight was increased depending on the pigment composition, while opacity increased linearly for all formulations. Gloss increased abruptly at low coat weights for all formulations and approached a plateau value at coat weight of 15-20g/$m^2$. Third order polynomial regression equations relating the coat weight with gloss have been derived and tabulated.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.118-119
• /
• 2019

The exterior finish not only has a relationship to the functionality of building, but also the spatial aesthetics and visual perception. Common exterior finishes are wood, stone or acrylic based and etc. However, these finishes have different attributes which can alter the quality of the architecture, such as durability, moisture and fire resistance. To make up for the short-comings of these materials, we have used iron based resources for optimization. However, iron materials are expensive, so they have limitations in general use. In this study, we have experimented with various forms of exterior finishes using cement, which is the most efficient and widely used building material with several economic advantages. We experimented with different materials to use as the formwork for the gloss of the cement matrix. As a result, the gloss show that order of urethane, steel, and wood material.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2005.11a
• /
• pp.243-250
• /
• 2005

• Journal of Adhesion and Interface
• /
• v.13 no.4
• /
• pp.171-181
• /
• 2012

The demand characteristics of the conventional 12 kinds of epoxy resins which have been used for restoration of the ceramic relics were investigated to provide standards of the effective materials in this study. The result of durability analysis showed that a liquid type is more effective in ceramic relics (low damage, high strength), and a paste type is more effective in earthenware relics (high damage, low strength). The result of workability analysis appears that the liquid type is higher than the paste type, and a slow curing type is higher than a fast curing type in surface hardness. Therefore, in the case of the liquid type which is hard to reprocess due to high surface hardness, it is necessary to conduct a study on improving physical properties by adding filler. The result of the gloss analysis on epoxy resins showed that the liquid type (colorless) has higher gloss than the paste type, and the slow curing type has higher gloss than the fast curing type in liquid types. CDK-520A/520B and Araldite SV 427-2/HV 427-1 showed the most similar gloss to $700^{\circ}C$ earthenware, Devcon 5 minute, EPO-TEK 301-2, and Quik Wood showed the most similar gloss to celadon and whiteware, Quik Wood, EPO-TEK 301-2, and Devcon 5 minute showed the most similar gloss to buncheongware. It is necessary for conservator to decide the range of the restoration surface by predicting the increase and decrease of the restoration surface because most of the epoxy resins caused the volume change in curing process.

• Corrosion Science and Technology
• /
• v.8 no.1
• /
• pp.15-20
• /
• 2009

Surface of PEEK(poly-ether-ether-ketone) was modified by chemical etching, plasma treatment and mechanical grinding to improve the plating adhesion. The plating characteristics of these samples were studied by the contact angle, plating thickness, gloss and adhesion. Chemical etching and plasma treatment increased wettability, adhesion and gloss. The contact angle of as-received PEEK was $61^{\circ}$. The contact angles of chemical etched, plasma treated or both were improved to the range of $15{\sim}33^{\circ}$. In the case of electroless plating, the thickest layer without blister was $1.6{\mu}m$. The adhesion strengths by chemical etching, plasma treatment or both chemical etching and plasma treatment were $75kgf/cm^2$, $102kgf/cm^2$, $113kgf/cm^2$, respectively, comparing to the $24kgf/cm^2$ of as-received. In the case of mechanically ground PEEKs, the adhesion strengths were higher than those unground, with the sacrifice of surface gloss. The gloss of untreated PEEK were greater than mechanically ground PEEKs. Plating thickness increased linearly with the plating times.

• Corrosion Science and Technology
• /
• v.2 no.5
• /
• pp.207-211
• /
• 2003

The weather resistance of five coatings systems based on alkyd, chlorinated rubber, epoxy, polyurethane and fluoropolymer were studied by natural exposure test and accelerated test. The coatings were exposed at Hanoi station with urban industry atmosphere and at Baichay station with marine atmosphere. The degradation of coatings was evaluated by gloss measurement and surface analysis by scanning electronic microscopy. The results obtained show that among coatings tested the gloss of polyurethane and fluoropolymer coatings remained highly and those of alkyd, chlorinated rubber and epoxy coatings were very low after two years of atmospheric exposure. Under accelerating conditions the gloss of fluoropolymer coatings remained highly after 80 cycles of testing. By comparison with accelerating test in UV-condensation chamber the conditions at atmospheric stations are more aggressive.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.49-57
• /
• 2001

This study was performed to identify the effect of calendering variables on the properties of coated paper such as sheet gloss, surface roughness, opacity, etc. The effect of calendering variables including the number of nips, pressure, machine speed and moisture content on the properties of coated paper was investigated. The calender was installed with two steel rolls and one cotton-made roll. With this calender, the coated sheets were passed through the calender from 1 to 4 times, applying the linear pressure on calender rolls, 5 through 100kg/cm and operating the machine speed 3 to 12m/min. Also, the moisture content of coated sheet was varied about 5 and 10%. It was found that sheet gloss and surface roughness of coated paper was increased with increasing the number of passing nips, linear roll pressure and the moisture content of coated paper. But it was shown that the opacity and brightness of coated paper were decreased under the above conditions due to the blackening. It was also suggested that the soft nip possibly increased the thermoplasticity of coating layer with the heat of steel roll, resulting in the reinforcement of surface properties positively. The sheet gloss and surface roughness of coated paper could be improved by the longer dwell time over the rolls.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.1
• /
• pp.22-29
• /
• 2002

The coated paper was greatly affected by the basic physical properties of the binder as well as the amount of the coating formula. High glass transition temperature (Tg) of the styrene-butadiene (SB) latex, selected as the binder in our study, gave the high stiffness to the coated paper, but lowered the binding force and print gloss. The average particle size of the SB latex also greatly affected to the coated paper so that the smaller particle size improved the rheological property of the coating formula and increased the binding force and print gloss. Another property of the SBR latex, gel content, was important because when its value was small, the latex was easily deformed at the high temperature and increased air permeability to the coated paper. Therefore, the lower gel content consequently resulted in the higher blistering resistance, especially in the web paper. The larger portion of the SB latex in the coated formula improved the binding force and print gloss, but decreased the ink set-off and ink-trapping to the coated paper. The heavier coating improved optical properties such as opacity, paper gloss and paper smoothness, to the coated paper.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.29 no.4
• /
• pp.289-294
• /
• 2015

In order to make digital processing of facial color, standardization methods of photographing and observational requirements and gloss-detecting are done through preceding papers and actual experiences. Examiner's observational informations should be contained with original and temporary color, normalcy and deviation range and gloss. And these are interrelated with time, interior and exterior temperature, emotional state, so should be recorded too. Picturing procedure should be controlled in simple and practical but objective way. Just water cleansing, 15 to 20 minute resting, prohibiton of moisturizing of examinee are common for examiner. Temperature and moisture, width, light source requirement, brightness, polarizing filter of parlor and camera-to-object distance, posture of examinee are should be recorded. In addition, pre and post-revision of color and manifestation of color space after taking images are needed coping with construction of diagnostic database.