• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.3
• /
• pp.100-109
• /
• 2022

In this study, calibration technology that increases the alignment accuracy in large flexible flat panels was studied. For precise of calibration, a systematization of the calibration algorithm was established, and a calibration correction technique was studied to revise calibration errors. A coordinate systems of camera and UVW stage was established to get the global position of the mark, and equations for translational and rotational calibration were systematically derived based on geometrical analysis. Correction process for the calibration data was carried, and alignment experiments were performed sequentially in cases of the presence or absence of calibration-correction. Alignment results of both calibration correction and non-calibration correction showed accuracy performance less than 1㎛. On the other hand, the standard deviation in calibration-correction is smaller than non-calibration correction. Therefore, calibration correction showed improvement of the alignment repeatability.

• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.1
• /
• pp.11-21
• /
• 2022

Fast Fourier transform (FFT)-based parallel acquisition techniques with reduced computational complexity have been widely used for the acquisition of binary phase shift keying (BPSK) global positioning system (GPS) signals. In this paper, we propose a low computational FFT-based fine acquisition technique, for binary offset carrier (BOC) modulated BPSK signals, that depending on the subcarrier-to-code chip rate ratio (SCR) selectively utilizes the computationally efficient frequency-domain realization of the BPSK-like technique and two-dimensional compressed correlator (BOC-TDCC) technique in the first stage in order to achieve a fast coarse acquisition and accomplishes a fine acquisition in the second stage. It is analyzed and demonstrated that the proposed technique requires much smaller mean fine acquisition computation (MFAC) than the conventional FFT-based BOC acquisition techniques. The proposed technique is one of the first techniques that achieves a fast FFT-based fine acquisition of BOC signals with a slight loss of detection probability. Therefore, the proposed technique is beneficial for the receivers to make a quick position fix when there are plenty of strong (i.e., line-of-sight) GNSS satellites to be searched.

• International conference on construction engineering and project management
• /
• 2020.12a
• /
• pp.30-37
• /
• 2020

In the building construction, the steel-frame work occupies an important position in terms of structure, cost and quality. Especially in Japan, steel frames have traditionally been the main structure of many buildings. For steel-frame works in such positions, this paper investigates an existing steel fabricator to clarify the actual conditions of design decision making process and management method in steel production process. This study focuses on a steel fabricator (Company M in the following sentences), whose main market is Japan and which has facilities in Thailand, China, and Japan. Company M uses QR codes to control the production status of products, and exchanges all information between inside and outside the company via specialized departments in the form of documents. The authors have already analyzed the relationship between production lead time and defect rate based on actual project data at Architectural Institute of Japan in 2016. In 2019, we expressed the process from the confirmation of the design information of the current steel frame to the production by WBS, and clarified the relationship between the production lead time and steel frame product quality structurally. In this paper, the authors reoport the progress of the survey conducted so far, the positioning of the collected data, and the future survey policy.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.3
• /
• pp.185-199
• /
• 2024

Global warming impacts every corner of human life. Maritime transportation and shipbuilding industries are no exception. Recent counteraction in maritime industries is accelerating to meet the zero emission by 2050. Various alternative energy sources have been studied, and recent developments in Europe show that the windship, as a proven technology, can be an attractive candidate to solve the problem. In this paper, as the alternative transportation option, to infer the performances of modern windships, the non-dimensional ratios of past tall ships and windships are studied and reviewed. In addition, the ratios are compared to estimate the position of current and future windships under consideration. It is found that regarding the ratio distributions, the current windships being planned can be either wind-assisted propulsion ships or less fully functional windships than the past tall ships.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.327-332
• /
• 2017

As Internet of Things (IoT) technology advances, there is a growing demand for location-based services (LBSs) to identify users' mobility and identity. The initial LBS system was mainly used to measure position information by measuring the phase of a signal transmitted from a global positioning system (GPS) satellite or by measuring distance to a satellite by tracking the code of a carrier signal. However, the use of GPS satellites is ineffective, because it is difficult to receive satellite signals indoors. Therefore, research on wireless communications systems like ultra-wide band (UWB), radio frequency identification (RFID), and ZigBee are being actively pursued for location recognition technology that can be utilized in an indoor environment. In this paper, we propose an LBS system that includes the 2.45GHz band for chirp spread spectrum (CSS), and the 3.1-10.6GHz band and the 250-750MHz bands for UWB using the IEEE 802.15.4a standard for low power-based location recognition. As a result, we confirmed that the 2.45GHz Industrial, Scientific and Medical (ISM) band RF transceiver and the ranging function can be realized in the hardware and has 0dBm output power.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.867-874
• /
• 2021

The IoT (Internet of Things) technology is rapidly becoming an important consideration in many engineering fields in the current 4th industrial era. In recent years, the concepts of digital shipbuilding and smart factories have been adopted as trends in shipyards. However, there is active interest in research on implementing autonomous driving in autonomous vehicles and airplanes, which is currently available in commercial form in a limited capacity. The present study is regarding the path-tracking performance of a boat to accomplish an autonomous driving mission using a flight controller (FC) and real-time kinematic (RTK) global positioning system (GPS) based on an open-source Ardupilot; an actual sea test is also performed using this system on a calm lake. The boat's mission is to evaluate the maneuverability of the self-driving process to a specific point and returning to the home position. For a given speed, the difference between the preset mission trajectory and actual operational trajectory was analyzed, and a series of studies were conducted on the applicability of the system to ships. In addition, the movements and maneuverability of the OmniX-type hull with four propellers were investigated, and the driving path-tracking performance was observed to increase by a maximum of 48%.

• Journal of Navigation and Port Research
• /
• v.43 no.1
• /
• pp.42-48
• /
• 2019

The significance of PNT information in the fourth industrial revolution is viewed differently in relation to the past. Autonomous vehicles, autonomous vessels, smart grids, and national infrastructure require sustainable and reliable services in addition to their high precision service. Satellite navigation system, which is the most representative system for providing PNT information, receive signals from satellites outside the earth so signal reception power is low and signal structures for civilian use are open to the public. Therefore, it is vulnerable to intentional and unintentional interference or hacking. Satellite navigation systems, which can easily acquire high performance of PNT information at low cost, require alternatives due to its vulnerability to the hacking. This paper proposed R-Mode (Ranging Mode) technology that utilizes currently operated navigation and communication infrastructure in terms of Signals of OPportunity (SoOP). For this, the Nationwide Differential Global Navigation Satellite System (NDGNSS), which currently gives a service of Medium Frequency (MF) navigation signal broadcasting, was used to validate the feasibility of a backup infrastructure in domestic maritime areas through simulation analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.8
• /
• pp.2052-2063
• /
• 1998

Various full-scale radio location systems have been developed since ground-based radio navigation systems appeared during World War II, and more recently global positioning systems (GPS) have been widely used as a representative location system. In addition, radio location systems based on cellular systems are intensively being studied as cellular services become more and more popular. However, these studies have been focused mainly on macrocellular systems of which based stations are mutually synchronized. There has been no study about systems of which based stations are asynchronous. In this paper, we proposed two radio location algorithms in microcellular CDMA systems of which base stations are asychronous. The one is to estimate the position of a personal station at the center of rectangular shaped area which approximates the realistic common area. The other, as a method based on road map, is to first find candidate positions, the centers of roads pseudo-range-distant from the base station which the personal station belongs to and then is to estimate the position by monitoring the pilot signal strengths of neighboring base stations. We compare these two algorithms with three wide-spread algorithms through computer simulations and investigate interference effect on measuring pseudo ranges. The proposed algorithms require no recursive calculations and yield smaller position error than the existing algorithms because of less affection of non-line-of-signt propagation in microcellular environments.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.11
• /
• pp.987-992
• /
• 2014

Register control of roll-to-roll printing system for printed electronics requires accurate measurement of register errors. The register marks used for the recognition of patterns position between layers have inherently defects due to low printability of register marks themselves, which brings out inaccurate register accuracy and consequently low performance of printed electronics devices. In this study, the compensation methods for the unrecognized or missing register data are proposed to improve the recognition and consequently the control performance of register accuracy in roll-to-roll printing equipment. The compensation methods using the prior data and the linear interpolation are proposed and compared with the case without compensation for the simulation as well as experiment. Only the linear interpolation method could successfully compensate the missing data and consequently improve the register control performance. We should apply the compensation process of the register errors to improve the register control accuracy in the roll-to-roll printing equipment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.8
• /
• pp.663-673
• /
• 2013

The drastic growth of mobile communication and spreading of smart phone make the significant attention on Location Based Service. The one of most important things for vitalization of LBS is the accurate estimating position for mobile object. Focusing on IMU deployed in smart phone, we develop a hybrid positioning estimation framework with a combination of WPS. The developed approaches can strengthen the advantages of independent indoor applicability of IMU. The estimation of IMU is efficiently compensated by radio fingerprint based Wi-Fi Positioning System. We put a focus especially on the hybrid algorithmic framework. Compared on the existing approaches of WPS or IMU, we achieve the comparable higher performance on both of average error of estimation and deviation of errors. Furthermore test-bed based on smart phone platform is practically developed and all data have been harvested from the actual measurement of test indoor area. This can approve the practical usefulness of proposed framework.